Microengine XP-GT3500L User manual

Quick Start Guide –XP-GT3500L /XP-GT3500ABL/XP-GTR1500L/XP-GTR1500LABX
Rev1.0 (20170313)
1
Note: Applicable to product model XP-GT3500L, XP-GT3500ABL, XP-GTR1500L, XP_GTR1500LABX
Software application version support:
-xPortal3000 v3.0.0.25 or later
-xPortalNet v1.5.0. 133 or later
1. Connect the Controller to Relay Board and Power supply (MPS-320). Please refer to the wiring
diagram for XP-GT3500 and XP-GTR1500 (Appendix 1)
2. Power on the devices
a. Controller will beep once. Keypad button will be lights on.
b. LCD shows initializing Database and display as follows:
c. After 1 sec, the LCD will change to idle screen.
Note: For the first time of new installation, please perform a ColdStart.
ColdStart is a process that will erase all the memory and reset all the setting to default.
3. To perform ColdStart,
a. Press and hold the “ColdStart” button on the board.
b. Power on the device. Hold the ColdStart button until a long beep from the device.
c. The controller memory will be cleared and initializing the database. This will take about
10 seconds.
4. To connect and link the controller to MicroEngine software, choose either ONE LAN or RS485
connection
a. For LAN connection, there are 3 methods to setup the network setting of the controller.
Note: Make sure the LAN cable is plugging into the network connector on the controller
board and the other end of LAN cable is connected to the network router or switches.
i. Device Lookup in xPortal3000.
Please visit to http://www.microengine.net/kb/article/AA-00512

Quick Start Guide –XP-GT3500L /XP-GT3500ABL/XP-GTR1500L/XP-GTR1500LABX
Rev1.0 (20170313)
2
ii. Login to Controller Web Diagnostic
1. Open Internet Explorer browser > Type http://192.168.1.20 (Default IP
address) in the address box
2. Enter the Username and password
a. Default Username is admin
b. Default Password is password10
3. After login successful, go to Configuration tab> Network menu>update
the necessary changes:
4. Set the IP address, Subnet mask, Gateway and Server IP.
5. Click Save.

Quick Start Guide –XP-GT3500L /XP-GT3500ABL/XP-GTR1500L/XP-GTR1500LABX
Rev1.0 (20170313)
3
iii. On-board keypad programming –Network setting menu.
Note: For the first time enter programming menu via on-board keyboard, user is
require to enter 6 digit new Master PIN. Default Master PIN is 123456.
Please visit to http://www.microengine.net/kb/article/AA-00267/0 and refer to
Controller Network Configuration.
b. For RS485 connection, please visit to http://www.microengine.net/kb/article/AA-
00269/0/
5. If the controller is connected and shows communication up in the software
xPortal3000/xPortalNet, you can add staff record/user database, configure the door parameter
in software. The controller setting will be updated immediately.
6. If the controller operate as standalone (Not connect to the software),
a. To add staff record /Card/ID,
Please visit to http://www.microengine.net/kb/article/AA-00314/0/

Quick Start Guide –XP-GT3500L /XP-GT3500ABL/XP-GTR1500L/XP-GTR1500LABX
Rev1.0 (20170313)
4
Appendix 1
1. Wiring Diagram for XP- GT3500
2. Wiring Diagram for XP-GTR1500