Microplex LOGIJET T4 User manual

________________________________________________________________________________
________________________________________________________________________________
LOGIJET T4
LOGIJET T6
LOGIJET T4 RFID
LOGIJET T6 RFID
Operator’s Manual
Edition 1.3L

2
_______________________________________________________________________________________________
_______________________________________________________________________________________________

Contents 3
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
Table of Contents
Chapter Page
1. Introduction 7
1.1. General Description 7
1.2. Information on RFID Technology 8
1.3. Fundamentals of Thermal Printing 9
1.4. Conventions 10
1.5. CE - Conformity 11
1.6. General Safety Regulations 11
2. Installation 14
2.1. Printer Unpacking 14
2.2. Check List 16
2.3. Printer Installation 17
2.4. Printer Components 18
3. Media and Ribbon Requirements 20
4. Basic Operation Sequences 21
4.1. Overview 21
5. Handling of Consumables 23
5.1. Winding Diagram 24
5.2. Roll-Fed Media Handling 25
5.2.1. Tear Off Media Loading 25
5.2.2. Media Removal 32
5.3. Handling of Ribbon (Foil) 33
5.3.1. Ribbon Loading 33
5.3.2. Ribbon Tension Adjustment 37
5.3.3. Ribbon Removal 40
5.4. Printhead Pressure Adjusting 42

4 Contents
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
Chapter Page
6. Control Panel 46
6.1. Attaching the Printer to a Computer 46
6.2. Turning on the Printer 46
6.3. Control Panel View 47
6.4. Function of the Control Panel Elements 48
6.5. Configuration via the Control Panel 51
6.6. Menu Structure 52
6.7. Syntax of Diagrams 56
7. Panel Functions 57
7.1. Print Process Selecting 57
7.2. Media Setting (Material; Label or Continuous) 59
7.3. Page Length Adjustment 60
7.3.1. Starting the (Printer’s) Measurement of Label Length 61
7.3.2. Configuration of Semiautomatic Label Length Measurement 61
7.4. Material Width Adjustment (Paper Width) 62
7.5. Configuration of Text Margins 63
7.6. Printing the Status Sheet 64
7.7. Printing the Font List 66
7.8. Hexdump-Mode Activation 67
7.9. Normal Print Mode Activation (incl. FORM FEED) 68
7.10. Clearing the Input Buffer (Cancel Job) 69
7.11. Printing the Menu Page 70
7.12. Generating Test Prints (Sliding Pattern) 71
7.13. Data Interface Selection 72
7.14. Emulation Selection 73
7.15. Display Language Selection 75
7.16. Transparent Code Adjustment 76
7.17. Selection of Memory Distribution (Input Buffer) 77
7.18. Setting to Factory Default 78
7.19. Font Selection 79
7.20. Text Orientation Selection 82
7.21. Symbol Code Selection 83
7.22. Print Speed Adjustment 84

Contents 5
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
Chapter Page
7.23. Contrast (Density) Setting 85
7.24. Image Shifting to the X-Direction 86
7.25. Image Shifting to the Y-Direction 88
7.26. Selecting the Light Sensor Type 90
7.27. Automatic Sync Sensor Adjust 91
7.27.1. Overview 91
7.27.2. Example 92
7.28. Manual Sync Sensor Adjust 93
7.28.1. Overview: Level and Current Adjusting 94
7.28.2. Description of Level and Current Adjusting 95
7.28.3. Example 96
7.29. Peripheral Device Activation (Tear Off Edge, Cutter) 98
7.30. Selecting the Tear Off Mode (Option: Cutting Mode) 100
7.31. Selecting the Print Mode 102
7.32. Adjusting the Tear Off Position (Option: Cutting Position) 105
7.33. Configuration of Network Parameters (IP Address, e.g.) 106
8. Using the RFID Functions 109
8.1. Integrated RF Write/Read module 109
8.1.1. CE - Conformity 109
8.2. RFID Panel Functions 111
8.2.1. Selecting the RFID Mode 111
8.2.2. Selecting the Communication Protocol 112
8.2.3. Adjusting the Transponder Position (Tag Position) 113
8.2.4. Adjusting the Number of RFID Access (Timeout) 119
8.2.5. Adjusting the Transmission Speed (Bit Rate) 120
8.2.6. Reading the Label Identification Number automatically 121
8.3. Data Interface Status Out 122
8.4. IDOL Commands for RFID 123
8.4.1. Overview Function Group RFID 123
8.4.2. Reading the Label ID Number (Prior to the Print Process) 126
8.4.3. Writing Data into a Data Block of the RFID Label 127
8.4.4. Generating a Page ID Number, Receiving the RFID data after Printing 128
8.5. Syntax of RFID Data (Status Messages) 130
8.6. RFID Errors 132

6 Contents
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
Chapter Page
9. Operator Maintenance 137
9.1. Printer Cleaning 137
9.1.1. Printer Cabinet Cleaning 138
9.1.2. Printhead Cleaning 139
9.1.3. Transport Roller Cleaning 142
9.2. Printhead Exchange 143
9.2.1. Printhead Removal and Installation 144
9.3. Adjusting the Right Pressure Value 148
10. Troubleshooting 149
10.1. Printer Error Messages 150
10.2. Reduced Print Quality 152
10.3. Incorrect Media Transport 154
10.4. Rewinder, Dispenser and Cutter Error Messages 155
10.5. Print Repetition after an Error 157
11. Measures for Transport and Shipping (Repacking) 159
12. Specifications 161
13. Appendix 165
13.1. Configuration of the Status Channel 165
13.1.1. Status Messages automatically or on Request 165
13.1.2. Changing the Separator and Terminator Characters 167
13.2. Survey of Print Job Status Messages 168
13.3. Survey of Printer Status Messages 169
14. Index 171

Introduction 7
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
1. Introduction
1.1. General Description
The LOGIJET T4 and LOGIJET T6 are multifunctional non-impact
printers based on thermal print technology.
The devices can be used for thermal transfer printing as well as for
thermal direct printing. Because of its wide range of application, you
can use them to print all kind of information as barcodes,
alphanumerical characters and vector graphics e.g. .
These printers not only know one device-specific page description
language as standard thermal printers usually do, but most of the
languages used in the industrial field and the well-known market
standards of laserprinters, too.
The printers LOGIJET T4 and LOGIJET T6 are provided with a
controller that is also used in SOLID laserprinters. So the
advantages of the thermal print technology are combined with the
flexibility of the „laserprinter intelligence“.
For the LOGIJET printers a software (called IP printADMIN) will be
available to allow a printer configuration via Ethernet. The
controller has its integrated website with information on the printer
status and the printjob status.
Data can be sent without programming expenditure from almost
any software platform, because printer drivers are already
available for this.
The capabilities featured include the MICROPLEX page description
language IDOL. Using this language, complex tasks such as the
creation of forms can be carried out by simple software commands
(see separate IDOL manual).
The resolution is 300 dots per inch corresponding to about 12 dots
per mm.
The print speed is 50 up to 150 mm/second.
Roll-fed media as well as continuous-media can be printed on.
The maximum processable width of media for the LOGIJET T6 is
174 mm. 168 mm of that are printable.

8 Introduction
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
1.2. Information on RFID Technology
The MICROPLEX printers LOGIJET T4 RFID and LOGIJET T6 RFID are
provided with an integrated multi-protocol RF Write/Read module.
The printer functions as a complete system for writing, reading and
printing RFID labels (Radio Frequency IDentification), when it is
connected to a host computer.
The printer receives instructions from the host computer. The MICROPLEX
Controller interprets this information and controls printer's mechanical
drive, RFID subsystem and printhead.
Fig. 1.2.a Block diagram: High Frequency Identification technology (RFID)
The multi-protocol RF Write/Read module is built-in in the printers paper path.
To use the RFID capabilities of this printer, you will need the appropriate
RFID media. This media includes the label, backing, and an RFID
transponder inlay encased by the label material.
The commands for the RFID functions are sent like print data via the
active data channel (Centronics, USB, Ethernet,...).
The ID of the label (Transponder Identification number) can be read in
order to be transmitted to the host via the printer's status channel.
This allows a clearly assignment of the specific label identification
number to the information printed on this label.
Antenna HF and
analog
circuit
Controller
Host
system
Energ
y
Data
RFID tag
(
Trans
p
onder
)

Introduction 9
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
Additionally the MICROPLEX firmware function "Status Out" provides the
possibility to get information on the printer status (paper jam, offline, ...)
and on the print job process (idle, busy, page printed,...).
1.3. Fundamentals of Thermal Printing
The thermal print technology enables a quiet and fast print process with a
high resolution output. The printhead produces the image by heating
single elements (dots). So you need a special ribbon (thermal transfer
printing) or a special kind of paper (thermal direct printing).
While thermal transfer printing the dots touch the thermal ribbon so that
the heating of particular dots leads to a partial melting of the ribbon. Due
to the contact with a media (future carrier of the information, for example
paper) this leads to a transfer of the image onto the media.
While thermal direct printing the dots touch the thermal paper directly.
The dyes and developers within the paper respond to the heat of
particular dots, change their colour to black and so the wanted image
emerges.
The LOGIJET T4 /T6 /RFID printers can be used for both methods of
printing.

10 Introduction
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
1.4. Conventions
!
OFFL.
blue colored text
[Menu Level 1 ]
To find the requested information more quickly and to
understand instructions more easily, the following conventions
are used:
This symbol refers to a possible source of danger. If you do not
pay attention to this information, injuries may result, the function
of the printer could be reduced or objects could be damaged.
This symbol refers to important hints and suggestions on using
the printer. Disregarding these hints might cause problems with
the printer or within the environments.
This symbol shows a key of the control panel. Such symbols will
be used in this manual whenever keys have to be pressed in
order to activate certain functions.
Link to another chapter or a different document. By clicking the
blue colored text you'll enter the concerning chapter or
document.
This symbol represents messages shown in the display (panel).

Introduction 11
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
1.5. CE - Conformity
The manufacturer hereby declares that the device complies with
the guideline RL 89/336/EWG for information technology
devices.
The determinations of the product standard concerning high
frequency interferences of information technology devices EN
55022, class A/DIN VDE 0878 (electromagnetic interference)
are complied.
Also the generic standard EN 50082-1/DIN VDE 0839 for
interference strength is complied.
The LOGIJET T4 RFID and LOGIJET T6 RFID printers incorporate
an integrated compact reader (RF Write/Read module).
The Declaration of Conformity can be found in section
8.1 Integrated RF Write/Read module.
1.6. General Safety Regulations
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Incorrect operation of this equipment in a
residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his
own expense.

12 Introduction
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
This MICROPLEX product and its consumables are designed
and tested according to strict safety standards.
Heeding the following instructions ensures secure operation:
- Please make sure your electricity source is appropriately
grounded.
- Install the device on solid and level ground.
- Only trained staff are authorized to transport the equipment.
- Only use consumables which are specially developed for this
device.
- Using unsuitable consumables may cause a reduction of output
quality or damages to the device.
- Ensure no liquids get on or into the device.
- Do not remove any cover or safety device fastened by screws.
- Do not remove or bridge over any safety device.
- Do not push anything into the ventilation apertures.
- Never carry out installations, cleanings or maintenance
operations which are not described in this manual. This should
only be done by MICROPLEX authorized service personnel.

Introduction 13
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
- Be careful when operating equipment with opened cover
hoods (setting-up work or service). Rotating parts can cause
injury , and it is also possible for hair, clothing, jewellery,
etc. to be caught in the machinery.
Ribbon and material should only be inserted and changed by
specially instructed personnel.
- Optional device components may only be installed by
authorized personnel, and in accordance with the
appropriate assembly and usage regulations.
- The cutter may only be installed by trained personnel.
- Only attach or remove the printhead when the device is
switched off.
After switching off the device, wait at least 3 minutes before
removing the printhead.
- Only plug in or remove interface connectors when the device
is switched off.
In order to disconnect the printer quickly from the main power
in case of emergency please note the following:
- For connected printers with plugs, the power-outlet should
be installed near the printer and easily within reach.
- For permanently connected printers, an easily accessible
emergency power-off switch should be installed close to the
printer.
- Please do not conceal any disconnect devices with the
printer or other objects.
- After switching off the device, wait at least 15 seconds
before the device is switched on again.
- Please follow all the information and hints directly attached
to the device and/or described in this manual.

14 Installation
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
2. Installation
2.1. Printer Unpacking
1. Open the box and remove the accessory parts.
Fig. 2.1.a Printer in the shipping box
2. Take the printer and lift it out the box carefully. Get
somebody to hold the box when removing the printer.
Take hold of the printer from the bottom.
Do not use other parts of the printer (e.g. plastic parts at the
printer's front or rear side ...) to lift the device!
Box contains
accessories
Printer

Installation 15
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
Fig. 2.1.b Lifting the printer
3. Remove the foil covering the printer.
4. Place the printer onto a suitable base (see section 2.3).
Please retain the original packing materials in case the printer
has to be transported in the future.

16 Installation
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
2.2. Check List
First of all place the printer and the accessories onto a level
surface until the definitive location is chosen.
Please make sure that all items are included and that there are
no defects.
Immediately inform your supplier of any damage.
Open the cardboard box carefully and check the contents:
1. Printer LOGIJET T4 /T6 /RFID
2. Power cord
3. Data cable (USB)
4. CD containing:
•Operator’s Manual for LOGIJET T4 /T6 /RFID
•Print drivers
•IDOL Programming Manual
Fig. 2.2.a Accessories

Installation 17
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
2.3. Printer Installation
- The chosen location should be well-ventilated, clean and dry.
- Damaging environmental factors such as metal vapors, oil mist,
corroding lixivium or the like must not come into contact with
the printer.
- Position the printer on solid and level ground.
- Do not exposure the printer to shocks or vibrations.
- The printer and socket have to be easily accessible.
- The printer should not be located near volatile or combustible
materials (e.g. a curtain).
- The printer must be connected to an appropriate AC power
source 120V AC/60 Hz (North America) or 230V/50 Hz
(Europe, United Kingdom e.g.). The power source must be
properly grounded. The socket and power cords must not be
damaged.
- Use the printer only within the allowed fluctuation range of
±10%.
- The voltage support must not be impaired by interference.
- In order to run the printer reliably, please maintain the
following environmental conditions:
Temperature: +5°C to +40°C (operating)
-20°C to +50°C (storage temperature)
Relative atmospheric humidity: 30% to 85% (without
condensation)
- Do not expose the printer to abrupt temperature changes
(heating, window or air condition).
- The printer should not be exposed to direct sunlight.

18 Installation
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
2.4. Printer Components
Main view:
Fig. 2.4.a Main view of the printer
Rear view:
Ethernet interface
Centronics interface
USB interface
Input power
connector
Power switch
Fig. 2.4.b Rear view of the printer
Window
Check the material / foil
supply without opening the
cover.
Cover
Open to insert material
and foil.
Display
Control Panel
LCD grafics display; 3
keys; displays printer
operation status, enables
settings via the menu.

Installation 19
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
Fig. 2.4.c Printer opened
Fig. 2.4.d Details printer mechanism
Lower cover Printhead
pressure lever
Cover
Control
panel
Label
supply
guide
Label roll
bar
Printer
mechanism
Platen roller
Dispense
sensor
Ribbon
rewind shaft
Ribbon
supply shaft
Tear off edge

20 Media and Ribbon Requirements
_______________________________________________________________________________________________
_______________________________________________________________________________________________
MICROPLEX Operator’s Manual LOGIJET T4 /T6 /RFID Edition 1.3
3. Media and Ribbon Requirements
Since print quality is affected by media and ribbon, printing speeds, and
printer operation modes, it is very important to run tests for your applications.
Fig. 3.a Labels
To use the RFID capabilities of this printer, you will need the appropriate RFID
media. This media includes the label, backing, and an RFID transponder inlay
encased by the label material.
High quality RFID labels are recommended to ensure against premature
printhead wear.
We strongly recommend the use of MICROPLEX supplies for continuous high-
quality printing.