MID WEST PRODUCTS GC-400R User manual

©2018 Mid West Products, Inc. -1- Form No. M1-1729
HANDY CADDY/”TRACTOR SEAT ON WHEELS”
MODEL GC-400R
Owner’s Manual and Parts List
SAVE THIS MANUAL
You will need this manual for the safety instructions, assembly instructions and parts list. Put it in a
safe, dry place for future reference.
Additional Information/Link to PDF Copy of this Manual:

©2018 Mid West Products, Inc. -2- Form No. M1-1729
1. Remove parts from carton and lay on a flat
surface.
2. Matching up all the predrilled holes, attach the
Tray Bracket (2) to the Frame (1), the Plastic Tray
(4) and the Reinforcing Plate (3) using the Screws
(14), SmallWashers(12), LockWashers(13), and
Small Nuts (15). Tighten hardware. See
Assembly Drawing above.
3. Slide both Axles (7) into the Frame (1). Slide the
Wheel (9) (be sure the valve stem is facing out),
and the Large Washer (10) onto the Axle. Thread
a Nylon Axle Nut (8) onto the end of Axle and
tighten, leaving enough space to permit theWheel
to turn freely. Repeat for the rest of the Wheels.
4. Be sure the Adjustment Lever (18) is screwed
onto Seat Post (6). The Seat (5) is attached to
the Seat Post (6) with four Tapered Bolts (16)
and Washer/Nylon Lock Nuts (17). Twist Seat
(5) and Seat Post (6) assembly into the Frame
(1) clockwise. The threaded Post needs to be
seen from below the Frame. Inset the Cotter Pin
(11) through hole in the Post. Spread open the
Cotter Pin (11).
5. Loosen Adjustment Lever (18) to set the desired
height. Adjust Seat height by rotating the Seat in
the Frame. Rotate Adjustment Lever (18) to
secure seat post in position. The Adjustment
Lever (18) will prevent the Seat from lowering
beyond the desired height. Before each use,
check the Seat (5) to make sure that the Seat is
securely in place with all hardware tightened
down.
ASSEMBLY
Please read all Instructions before assembly and using the product!
1. Keep work area clean and uncluttered to avoid injuries.
2. Keep children away from this product. This is not a toy.
3. Use eye and ear protection. Always wear approved impact safety goggles when assembling thisproduct.
4. Do not overreach. Keep proper footing and balance at all times when assembling this product.

©2018 Mid West Products, Inc. -3- Form No. M1-1729
OPERATION
1. Mount your Caddy as you would a bicycle.
Keeping feet on the ground.
2. When moving forward, do it in a walking fashion at
a slow pace.
SAFETY INSTRUCTIONS
1. Do not exceed the Recommended ProductWeight
Capacity of 300 pounds. Doing so can result in
personal injury and/or damage to the product. If
you sit down quickly onto the work seat, it may
create for a brief instant, an excess load, which
may result in damage to the work seat and/or
personal injury.
2. Do not use this Handy Caddy as a toy. It is not
designed for use by children.
3. Do not use on inclines or city streets.
PARTS LIST
Key
Part No.
Description
Qty.
1
20-4001
Frame
1
2
20-4002
Tray Bracket
2
3
20-4003
Reinforcing Plate
2
4
20-4004
Plastic Tray
1
5
20-4005
Seat
1
6
20-4006
Seat Post
1
7
20-4007
Axle
2
8
20-4008
Nylon Axle Nut
4
9
20-4009
Wheel
4
10
20-4010
Large Washer
4
11
20-4011
Cotter Pin
1
12
20-4012
Small Washer
4
13
20-4013
Lock Washer
4
14
20-4014
Screw
4
15
20-4015
Small Nut
4
16
20-4016
Tapered Bolt
4
17
20-4017
Washer/Nylon Lock Nut
4
18
20-4018
Seat Adjustment Lever
1
INSTRUCTIONS FOR ORDERING PARTS
(Minimum Parts Order Charge $20.00)
1. Address all parts orders or correspondence regarding customer service to one of the following:
Parts Dept.
Phone:
[phone]
Mid West Products, Inc.
P.O. Box 301
E-mail:
[e-mail]
Phillipsburg, OH 45354
Website:
www.Mid-West-Products-Inc.com
2. Write your name and address plainly (print or type).
3. Explain where and how to ship.
4. Give model number of unit.
5. Give part number from parts list, as well as a description, including color, of the part and the quantity you
need.
6. Inspect all shipments you receive. If any parts are damaged or missing, file a claim with the carrier before
accepting.
7. If you are returning parts, be sure to include WITH THE SHIPMENT a list of the parts with your name and
address.
8. All orders for repair and replacement parts will be shipped when paid with Master Card, Visa, or personal
check/money order. Prices subject to change without notice.
GUARANTEE
The merchandise you have purchased from us has been carefully engineered and manufactured under
Mid West Products rigid quality standards and should give you satisfactory, dependable operation.
However, like all mechanical merchandise, it may occasionally require adjustment or maintenance.
Should you need technical assistance, please contact MID WEST PRODUCTS.

©2018 Mid West Products, Inc. -4- Form No. M1-1729
OTHER LAWN & GARDEN TOOLS FROM
MID WEST PRODUCTS, INC.
WOODEN UTILITY CARTS —GC-20 OR GC-26
It has a gate that lifts out to unload bulky loads like mulch, soil, gravel, firewood or waste
and also allow it to carry longer items. Once you have one, you’ll wonder what you ever
did without it!
The Standard-Duty Utility Cart has two 20” Pneumatic Wheels and a cargo capacity of 6.5
cubic feet or up to 300 pounds.
The Heavy-Duty Utility Cart has two 26” Pneumatic Wheels and a cargo capacity of 11.3
cubic feet or up to 400 pounds.
VEGETABLE GARDEN ROW SEED PLANTER —GSF-31M
ALL-IN-ONE item that can simultaneously Plant and Fertilize Seeds as well as Mark
Rows.
It only weighs 14 lbs. and NO TOOLS are REQUIRED for Assembly.
Attached Pouch for extra seed, notes, gloves, and other needed items.
High Strength Powder Coated Steel Frame and Seed Tube.
The unit is Rear-Wheel Belt Driven for Positive, Even Seeding and No Messy Chain to
pull the seeds out of the ground.
Includes 6 Different Seed Plates for 31 Common Variations in Seed Sizes.
HIGH WHEEL CULTIVATOR —HWC-243A
24” Steel Wheel For Easy Handling
Special Selection of 3 Tools (Mol-board Plow, Reversible Shovel, Welded Five-Tine
Cultivator)
Slotted Foot For Plow Attachments Enables Easy Adjustment of Cutting Depth and
Angle
Handle Folds Easily For Storage or Transportation
31” DELUXE PUSH LAWN SWEEPER —B-319
The “Butterfly” Handles Increase the Hamper Capacity to a Huge 8.5-Bushel.
Big 10” Precision Molded Plastic Wheels with Ribbed Tread Rubber Tire…Makes this
Unit Easy to Push.
The Rear Swivel Casters Help Make this Easy to Maneuver.
Our Easy to Operate One-Hand “Squeeze Me” Height Adjustment Makes it Easy to go
From Grass to Pavement.
The Removable Hamper Allows for Easy Dumping and Fold Away Storage.