Midas Touch MTA-3080 User manual

MTA-3080
8" Risc-based IoT Terminal
User Manual
使用手冊

Version 1.0
Copyright Notice
Copyright © 2018 Midas Touch, Inc. All rights reserved
This document contains proprietaryinformation protected by copyright.All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of the
manufacturer.
Disclaimer
The information in this document is subject to change without prior notice in order
to improve the reliability, design and function. It does not represent a commitment
on the part of the manufacturer.
Under no circumstances will the manufacturerbe liablefor any direct,indirect,
special, incidental, or consequential damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of such
damages.

III
Federal Communications Commission (FCC) Statement
15.21
Youare cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try tocorrect the interference byone or moreof the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.Operation is subject to the
following two conditions:
1) this device may not cause harmful interferenceand
2) this device must accept any interference received, including interference that
may cause undesired operation of thedevice.
FCC RF Radiation Exposure Statement:
For body worn operation, this phone has been tested and meets FCC RF
exposure guidelines when used with an accessory that contains no metal and
that positions the handset a minimum of 1.5 cm from the body. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines.

IV
NCC警語：
根據NCC低功率電波輻射性電機管理辦法 規定: 第十二條 經型式認證合
格之低功率射頻電機，非經許可，公司、商號或使用者均 不得擅自變更
頻率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經
發現有干 擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前
項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍
受合法通信或工業、科學及醫療用電波輻射性電機 設備之干擾。
「減少電磁波影響，請妥適使用」。
「SAR標準值2.0W/Kg；SAR實測值為：0.222W/Kg」。
「EMC品質符合CNS13438限制值，充電線組限用原廠含鐵粉芯、1米
長之隔離線_USB Cable」。
產品規格
產品額定電壓 / Rating Voltage: D.C. 12V~24V
操作溫度範圍 / Operate temp.: -10~50℃
防水防塵等級 / water and dust-proof.: IP65

1
Package Contents:
MTA-3080 8" Risc-Based Panel PC
2-pin Power Terminal Block Connector
Wi-Fi/BluetoothAntenna
1M USBCable
User Manual
12 13 14 15 16
1
2.0 megapixel camera
11
Panel mounting holes
2
Microphone
12
10/100 Mbps RJ-45 LAN port
3 5-pointprojectedcapacitivetouch
screen
13 2 x USB2.0 ports
4 Integrated2W speaker 14 DB-9RS-232port
5 NFCantennaarea* 15 DB-9RS-232/422/485port
6 4x3.3V GPIO, 1 x CAN 2.0b / OBD-II 16 Poweron/off toggle switch
7 2-pin DCterminal connector,
12V~24Vauto-detection 17 4Gantennaconnector*
8 microSDcard slot 18 Wi-Fi/Bluetoothantennaconnector
9 Micro SIM(3FF) slot 19 3G/4Gantennaconnector*
10 UARTConnector 20 VESA75mountingholes(M3size)
*3G,4G andNFC areoptional modules andyourMTA-3080maynotcome with these
components.
Open Your Box
9 8
3
2 1
6 7
17
18
19
10
11
5
4
20
11

2
Install microSD Card
3GAntenna
4G Antennas
Toinstall a microSD card to the device, locate
the microSD card slot on the side and insert
the card following the direction as shown in
the picture. Push the card into the slot until it
locks into place.
Install SIM Cards & Antenna
SIM Card Installation
The MTA-3080 accepts micro SIM (3FF) card.
Toinstall a SIM card to the device, locate the
SIM card slot on the side and insert the card
following the direction as shown in the picture.
Push the card into the slot until it locks into
place.
3G/4G Antenna Connection
According to the type of mobile network supported by your MTA-3080, attach
appropriate antenna to the MTA-3080.
Touse 4G mobile network, attach
two4G antennas asshownbelow. To use 3G mobile network, attach one
3G antenna as shown below.
Wi-Fi/Bluetooth AntennaConnection
The MTA-3080 comes with a Wi-Fi/Bluetooth
antenna to help increasing the signal strength.
Touse the antenna, attache the Wi-Fi/
Bluetooth antenna to the Wi-Fi/Bluetooth
antenna connector.
Wi-Fi/Bluetooth
Antenna

3
Power Connection
The MTA-3080comes with one 2-pin DC terminal block connector to connect
power to DC power connector on the device.Touse the block connector:
1. Use a wire-stripping tool to strip both of the wires from the DC-input
power source. Expose the wire to the appropriate length for the DC power
connector.
2. Insert the wires into the DC power connector terminals and use a
screwdriver to tighten the two captive screws on the connector.
Pin Description
1 Power_GND
2 +12V- 2 1
3. Connect the DC terminal block
connector to the power connector
on theMTA-3080.
4. Enable DC power by plugging
in the DC power supplycord to
a power source, or by enabling
power at the designatedcircuit.
After power connection, toggle the
power switch to ON to turn on the
device.

4
Connector Pinouts
PWPIN
Description: Power Input Connector
Connector Type: 2-pin Terminal Block
Pin Description 2 1
1 Power_GND
2 +12V-
GPIO and CAN Bus
Description: Digital General Purpose
Signal Input/Output and CAN
Connector Type: 4x 3.3V Digital GPIO
connector and 1 x CAN2.0b Bus 1 10
Pin
Description
Pin
Description
1
IO_GND
6
GPIO_4
2
GPIO_1
7
IO_GND
3
GPIO_2
8
CANL
4
IO_GND
9
CANH
5
GPIO_3
10
IO_GND
Note: The pin assignments of other connectors conform to the industry standard.

5
包裝內容:
MTA-3080 8" RISC架構平板電腦
2-pin電源端子座
Wi-Fi/藍芽天線
1MUSB 連接線
使用手冊
12 13 14 15 16
1 2百萬畫素相機 11 安裝孔
2 麥克風 12 10/100MbpsRJ-45LAN網路連接埠
3 5點投射電容式觸控螢幕 13 2 x USB 2.0 連接埠
4 內建2W 喇叭 14 DB-9RS-232連接埠
5 NFC 天線位置* 15 DB-9RS-232/422/485連接埠
6 4x3.3V GPIO, 1 x CAN 2.0b / OBD-II 16 電源開關
12V~24V 自動偵測
*3G 、 4G 及 NFC 為選配模組，您的 MTA-3080 可能不包含這些元件。
MTA-3080 概覽
9 8
3
2 1
6 7
17
18
19
10
11
5
4
20
11
7 2-pin DC 電源端子連接器 17
4G天線連接埠*
8
microSD 卡插槽
18
Wi-Fi / 藍芽天線連接埠
9
Micro SIM卡插槽 (3FF)
19
3G/4G 天線連接埠*
10
UART 連接埠
20
VESA 75 安裝孔 (M3)

6
4G天線 x 2
若要安裝microSD卡，請將microSD卡依右圖
所示，將卡片插入裝置側邊的microSD卡插槽，
然後將卡片直推到底，確定完全插入。
安裝 SIM 卡及天線
SIM卡安裝
MTA-3080所支援的SIM卡格式為micro SIM
(3FF)。若要安裝SIM卡，請將SIM卡依右圖所
示，將卡片插入裝置側邊的SIM卡插槽，然後
將卡片直推到底，確定完全插入。
連接3G/4G天線
請根據您的MTA-3080所支援的無線行動網路類型 (3G或4G)，連接對應的無線
行動網路天線。
若您的MTA-3080使用4G無線行動
網路，請依下圖在左右兩邊的天線
連接埠各連接一支4G天線。
若您的MTA-3080使用3G無線行動
網路，請依下圖在右邊的天線連接
埠連接一支3G天線。
3G天線
連接Wi-Fi/藍芽天線
MTA-3080隨貨附有一個Wi-Fi/藍芽天線用以加
強無線訊號，請將該天線連接到MTA-3080的
Wi-Fi/ 藍芽天線連接埠。
安裝 microSD 卡
Wi-Fi/藍芽天線

7
連接電源
MTA-3080隨貨提供一個2-pin的DC電源端子座，用以連接裝置的DC電源端子連
接器，請依下列步驟連接電源：
1. 用剝線鉗將DC電源線剝去外皮，露 ft 可以插入端子座線孔的適當長度。
2. 依腳位定義將DC電源線插入端子座的線孔，然後用螺絲起子旋緊線孔的螺
絲，將線材固定。
Pin 說明
1 Power_GND
2 +12V- 2 1
3. 將DC電源端子座插入MTA-3080的電源端子連接器。
4. 將DC電源線接上電源。
連接電源後，將電源開關撥到ON的位
置即可開啟裝置。

8
PWPIN
說明: 電源輸入孔
連接埠類型: 2-pin端子座
Pin 說明 2 1
1 Power_GND
2 +12V-
GPIO 及CAN Bus
說明: 通用型輸入輸ft及CAN
連接埠類型: 4x 3.3V GPIO 連接埠及 1 x
CAN 2.0b Bus 10
注意: 其它連接埠的Pin腳定義皆同業界標準。
Pin腳定義
Pin
說明
Pin
說明
1
1
IO_GND
6
GPIO_4
2
GPIO_1
7
IO_GND
3
GPIO_2
8
CANL
4
IO_GND
9
CANH
5
GPIO_3
10
IO_GND