Middle Atlantic Products VDM-200-T User manual

I-00808 Rev A
VDM-200-T
Tilt Wall Mount
Instruction Sheet
Thank you for purchasing the VDM-200-T tilt wall mount. Please read these instructions thoroughly
before installing or assembling this product.
PRODUCT FEATURES
THANK YOU
• Up to 15 degrees of limitless tilt
• Post-install leveling mechanism enables quick micro-adjustment of horizontal plane of display
• Safety locking features keep the display securely mounted
• VESA Capability 75x75mm - 200x200mm

IMPORTANT SAFETY INSTRUCTIONS / INSTRUCTIONS IMPORTAANTES SUR LA SÉCURITÉ
SAVE ALL INSTRUCTIONS / CONSERVER CES INSTRUCTIONS
CAUTION/ATTENTION and the exclamation point within an
equilateral triangle is intended to alert the user to the possibility of
damaging or destroying the equipment if the instructions are not
followed.
Attention et le point d'exclamation dans un triangle équilatéral est
destiné à alerter l'utilisateur de la possibilité d'endommager ou de
détruire l'équipement si les instructions ne sont pas suivies.
WARNING/AVERTISSEMENT and the exclamation point within an
equilateral triangle is intended to alert the user to the possibility of
serious injury or death if the instructions are not followed.
Avertissement et le point d'exclamation dans un triangle équilatéral
est destiné à alerter l'utilisateur de la possibilité de blessures
graves ou la mort si les instructions ne sont pas suivies.
Page 2
WARNING: Failure to read, understand and follow the following information can result in seri-
ous personal injury, damage to the equipment or voiding of the warranty.
AVERTISSEMENT: Ne pas lire, comprendre et suivre les informations suivantes peut entraîner
des blessures graves, des dommages à l'équipement ou de la nullité de la garantie.
WARNING: Failure to provide correct structural strength for the component may result in seri-
ous personal injury or damage the equipment. The 2x4 stud wall to which the component is
being attached may have a maximum drywall thickness of 5/8” (1.6 cm).
AVERTISSEMENT: Le défaut de fournir une résistance structurelle correcte pour le composant
peut entraîner des blessures graves ou endommager l'équipement. Le goujon de 2x4 auquel le
composant mur est connecté peut avoir un maximum de 1.6 cm (5/8”) d'Épaisseur cloison
sèche.
WARNING: Exceeding the weight capacity may result in personal injury or equipment damage.
The combined weight of all components attached to the mount must not exceed weights listed
on page 3.
AVERTISSEMENT: Dépasser la capacité de poids peut entraîner des blessures ou des dom-
mages matériels. Le poids combiné de tous les composants reliés au support de montage ne
doit pas dépasser les grammages indiqués à la page 3.
WARNING: Be aware of pinch points and do not place fingers in between moving parts.
AVERTISSEMENT: Soyez conscient des points de pincement et de ne pas placer les doigts
entre les pièces mobiles.
WARNING: Use this product for its intended use and only use attachments recommended by
the manufacturer.
AVERTISSEMENT: Utilisez ce produit pour son utilisation prévue et utiliser uniquement les
accessoires recommandés par le fabricant.
WARNING: Do not use a damaged product. Return damaged products to a qualified service
center for repair.
AVERTISSEMENT: Ne pas utiliser un produit endommagé. Retour produits endommagés à un
centre de service qualifié pour la réparation.
WARNING: Not intended for outdoor use.
AVERTISSEMENT: Non destiné à une utilisation en extérieur.

Page 3
WEIGHT RATINGS
Model Weight Rating
VDM-200-T 80 lbs. Maximum Total Rated Load
• #2 Phillips Screwdriver
• Drill
• Protective Eyewear
• 5/32” Wood Bit or 3/8“ Masonary Bit
• Level
• Hammer
• 3/8” Hex Socket
• 4mm Hex Key (Supplied)
TOOLS REQUIRED
WARNING: Use tools with caution and follow all necessary safety protocols.
AVERTISSEMENT: Utiliser des outils avec prudence et suivre tous les protocoles de sécurité
nécessaires.

Page 4
SUPPLIED COMPONENTS
(3)
#14 x 2.5”
Hex Head Screw
(C)
(3)
Wall Anchor
(D)
(4)
M6 Spacer
(G)
(1)
Wall Mount Bracket
(A)
(1)
Display Mount
(B)
(4)
M5 Washer
(E)
(4)
M8 Washer
(F)
(4)
M4 x 20
(H-B)
M5 x 30
(H-D)
M6 x 20
(H-F)
M6 x 30
(H-J)
M5 x 12
(H-C)
(4) (4)
M6 x 12
(H-E)
(4) (4) (4)
M4 x 12
(H-A)
Display Mount Screws
M8 x 16
(H-H)
(4)
M8 x 20
(H-J)
(4)
(4)
(1)
4mm Hex Key
(J)

WOOD STUD WALL BRACKET INSTALLATION
Page 5
1. Determine height for display and find center of stud closest to desired position on wall.
2. Using a level, scribe a 4” long line down the center of the stud. (FIGURE A)
FIGURE A
3. Using the wall mount bracket (A) as a template, mark the center of the 3 mounting holes along the scribed
center line. (FIGURE B)
Mounting holes
4. Remove Wall Mount Bracket and using a 5/32” drill bit, drill a 2.5” deep pilot hole in each of the
three marked center points.
A
(FIGURE B)

WOOD STUD WALL BRACKET INSTALLATION CONT.
Page 6
1) Install wall mounting bracket using (3x) supplied #14 x 2.5” hex head screws, orienting bracket as shown.
(FIGURE C)
CA
NOTE: Flange must face up.
BLOCK OR CEMENT WALL BRACKET INSTALLATION
1. Determine the desired position height for display on wall and using a level, scribe a 4” long line down the
the concrete or block wall. (FIGURE D)
FIGURE D
FIGURE C

BLOCK OR CEMENT WALL BRACKET INSTALLATION CONT.
Page 7
2. Using the Wall Mount Bracket (A) as a template, mark the center of the 3 mounting holes along the scribed
center line. (FIGURE E)
Mounting holes
3. Remove Wall Mount Bracket and using a 3/8” drill bit, drill a 2.5” deep hole in each of the 3 marked
center points.
4. Press a wall anchor (D) into each drilled hole (Wall Anchors may require a hammer to install) (FIGURE F)
5. Install Wall Mounting Bracket (A) using (3x) #14 x 2.5” hex head screws (C), oriented bracket as shown.
To prevent anchors from stripping, only use a hand tool to install screws. (FIGURE G)
Wall Mounting Bracket
(A)
C
A
Flange must face up.
D
FIGURE E
FIGURE F FIGURE G
NOTE: Wall anchors may
require a hammer
to install.
NOTE: To prevent anchors from
stripping, only use a hand
tool to install.

H-A - H-J
E or F
B
FLUSH DISPLAY MOUNT BRACKET INSTALLATION
Page 8
1. Using supplied (4x) display mount screws, select the appropriate screw size and length ensuring screw
does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop
immediately and try a shorter screw. If supplied screws are still too long, use supplied spacers to take up
slack.
2. Align display mount (B) with mounting holes on the back of display. Using (4x) washers (E or F) and (4x)
display mount screws (H-A - H-J) to secure the display mount to your display. (FIGURE H)
FIGURE H
TV
TV
TV TV

E or F
B
G
RECESSED OR RAISED DISPLAY MOUNT BRACKET INSTALLATION
Page 9
FIGURE J
H-A - H-J
1. Using supplied (4x) display mount screws (H-A - H-J), select the appropriate screw size and length ensuring
screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop
immediately and try a shorter screw. If supplied screws are still too long, use supplied spacers to take up
slack.
2. Align display mount (B) with mounting holes on the back of display. Using (4x) washers (E or F), (4x)
display mount screws (H-A - H-J) and (4x) spacer (G) to secure the display mount to your display.
(FIGURE J)
TV
TV
TV TV

RECESSED DISPLAY MOUNT BRACKET INSTALLATION
Page 10
1. Align tabs on display mount with holes in wall bracket and slide down to lock into place. (FIGURE K)
2. Tighten security screw down into wall plate to lock display
into place. (FIGURE L)
FIGURE K
FIGURE L