Middle Atlantic Products Lace Series User manual

100-00017 Rev A
THANK YOU
PRODUCT FEATURES
• Multiple depths of 0", 2" (50.8 mm), 4" (101.6 mm), or 6" (152.4 mm) offset on a single lace bar for
cable/signal separation.
• Use optional LL-VA21 Lever Lock™ product (not provided) for multiple depth application.
• Easy break off tabs allows for flexibility.
Thank you for purchasing an Adjustable Horizontal Lace option. Please read these instructions
thoroughly before installing or assembling this product.
Lace Series
Adjustable Horizontal Lace Option
Instruction Sheet

REQUIRED TOOLS
Page 2
• Cutting Pliers
• #2 Phillips Screwdriver
• File
SUPPLIED COMPONENTS AND HARDWARE
WARNING: Use tools with caution and follow all necessary safety
protocols.
AVERTISSEMENT: Utiliser des outils avec prudence et suivre
tous les protocoles de sécurité nécessaires.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, understand and follow the following information can result in serious personal injury, damage to the
equipment or voiding of the warranty. It is the responsibility of the Installer/User to ensure that this product is loaded according to
specifications.
WARNING: Middle Atlantic Products, Inc. electrical systems conform to and should be properly grounded in compliance with
requirements of the current National Electrical Code or codes administered by local authorities.
All electrical products may present a possible shock or fire hazard if improperly installed or used. Middle Atlantic Products, Inc.
electrical products may bear the mark of a Nationally Recognized Testing Laboratory (NRTL) and should be installed in confor-
mance with current local and/or the National Electrical Code.
WARNING: A warning alerts you to a situation that could result in serious personal injury or death.
AVERTISSEMENT: Un avertissement vous avertit d'une situation pouvant entraîner des blessures graves ou la mort.
INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ
AVERTISSEMENT:Refus de lire, comprendre et suivre la renseignements suivants peut traduire par de graves blessures, des
dommages à l'équipement ou invalider la garantie. Il est la responsabilité de l'installateur / utilisateur de s'assurer que ce produit
est chargé conformément aux spécifications.
AVERTISSEMENT: Middle Atlantic Products, Inc. électrique systèmes conformes à devraient être mis à la terre dans conformité
avec les exigences de la National actuelle ou comme les codes électrique administré par les autorités locales autorités.
Tous les produits électriques peuvent présenter un choc ou un incendie danger si elle est mal installé ou utilisé. Middle Atlantic
Products, Inc. produits électriques peuvent porter la marque d'un Nationally Recognized Testing Laboratory (NRTL) et doit être
installé en conformité avec courant local et/ou le National Electrical Code.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Clean only with dry cloth.
• Only use attachments/accessories specified by the manufacturer.
• Lire ces instructions.
• Conservez ces instructions.
• Respectez tous les avertissements.
• Suivez toutes les instructions.
• Nettoyer uniquement avec un chiffon sec.
• N'utilisez que des accessoires spécifiés par le fabricant.
(2x Pair) Adjustable Lacing Ears
A
(2x) Horizontal Lacer Bar
B
(10x) Plastic Rivets
C

INSTALLING THE HORIZONTAL LACER BAR TO PAIR OF LACING EARS
Page 3
INTRODUCTION
NOTE:
• While two complete horizontal lace options
are provided, this instruction sheet
shows the installation of one.
Repeat the entire process to install the
second, if necessary.
• Adjustable lacing ear pairs are indicated with
a single dot on one side and two dots on the
other as shown. (FIGURE A)
SIZING THE LACING EARS (OPTIONAL)
NOTE: The lacing ears (A) are 6” (152.4 mm) in length when left uncut.
• Apply pressure at perforations by hand to size your pair of lacing ears (A) to 2” (50.8 mm) or
4” (101.6 mm) lengths, if desired. (FIGURE B)
NOTE: You can also size the ears (A) by using cutting pliers to snip at the perforations, if desired.
FIGURE A
• Use (4x) plastic rivets (C) to attach the horizontal lacer bar (B) to the lacing ears (A) as shown.
(FIGURE C)
NOTE: A single dot on one ear (A) and
two dots on the other make one pair.
FIGURE C
A
C
B
FIGURE B
A
A
Size by hand or
snip at perforations
on both ears (A) to
match 2” (50.8 mm)
or 4” (101.6 mm)
lengths, if desired.
6” (152.4 mm)
2” (50.8 mm)
4” (101.6 mm)
CAUTION: File down any rough edges
after sizing the ears.
ATTENTION: Limez les aspérités
après avoir redimensionné les oreilles.

Page 4
INSTALLING THE HORIZONTAL LACE OPTION TO RACKRAIL
Outside Installation
1. Position your horizontal lacing option upright (with the lacing ear flanges on top) as shown. (FIGURE D)
2. Use a #2 Phillips screwdriver and (4x) rackscrews (not provided) to attach the lacing option
(2x rackscrews per ear) to the rackrail in an outside or inside installation as shown. (FIGURE E and F)
NOTE:
• Always attach the
horizontal lacing option
upright (with lacing ear
flanges on top) whether
installing in outside or
inside installations.
• Rackrail isolated for clarity.
Rackscrews
(Not Provided)
FIGURE E
Horizontal lacing option
in upright position
(with lacing ear flanges on top).
FIGURE D

Inside Installation
NOTE:
• Always attach the
horizontal lacing option
upright (with lacing ear
flanges on top) whether
installing in outside or
inside installations.
• Rackrail isolated for clarity.
Page 5
INSTALLING THE HORIZONTAL LACE OPTION TO RACKRAIL (CONTINUED)
TIP: Use LL-VA21 Lever Lock™ pieces (not provided)
for a multi-plane mounting configuration as shown.
(FIGURE G)
LL-VA21 Lever Lock™
pieces (not provided)
shown mounted to the
adjustable horizontal lace
option.
FIGURE G
FIGURE F
Rackscrews
(Not Provided)

WARRANTY
Page 5
For warranty information, refer to http://www.middleatlantic.com/company/about-us.aspx#warranty
Corporate Headquarters
Voice: 973-839-1011 - Fax: [phone] - International Voice: [phone] -
Fax: [phone] - www.middleatlantic.com - [email protected]
Middle Atlantic Canada
Voice: 613-836-2501 - Fax: [phone] - ca.middleatlantic.com -
[email protected]
Middle Atlantic EMEA Technical Support
Voice: [phone] - [email protected]
Factory Distribution
United States: New Jersey, California, Illinois - Canada: Ontario - The Netherlands: Weert
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.