Middle Atlantic Products VDM-600-M User manual

I-00805 Rev A
Instruction Sheet
VDM Series
Full-Motion Display Mount
Thank you for purchasing the Vision Display Full-Motion display mount.
Please read these instructions thoroughly before installing or assembling these products.
• Ideal for corner mount installs and single-person servicing
• Cable management built into arms to help maintain signal integrity and aesthetics
• Safety locking features keep the display securely mounted
• Arm extends 20”
• VESA Capability:
VDM-600-M 200x200mm - 600x400mm
VDM-800-M 200x200mm - 800x600mm
THANK YOU
PRODUCT FEATURES
VDM-600-M VDM-800-M

IMPORTANT SAFETY INSTRUCTIONS / INSTRUCTIONS IMPORTAANTES SUR LA SÉCURITÉ
SAVE ALL INSTRUCTIONS / CONSERVER CES INSTRUCTIONS
CAUTION/ATTENTION and the exclamation point within an
equilateral triangle is intended to alert the user to the possibility of
damaging or destroying the equipment if the instructions are not
followed.
Attention et le point d'exclamation dans un triangle équilatéral est
destiné à alerter l'utilisateur de la possibilité d'endommager ou de
détruire l'équipement si les instructions ne sont pas suivies.
WARNING/AVERTISSEMENT and the exclamation point within an
equilateral triangle is intended to alert the user to the possibility of
serious injury or death if the instructions are not followed.
Avertissement et le point d'exclamation dans un triangle équilatéral
est destiné à alerter l'utilisateur de la possibilité de blessures
graves ou la mort si les instructions ne sont pas suivies.
WARNING: Failure to read, understand and follow the following information can result in seri-
ous personal injury, damage to the equipment or voiding of the warranty.
AVERTISSEMENT: Ne pas lire, comprendre et suivre les informations suivantes peut entraîner
des blessures graves, des dommages à l'équipement ou de la nullité de la garantie.
WARNING: Failure to provide correct structural strength for the component may result in seri-
ous personal injury or damage the equipment. The 2x4 stud wall to which the component is
being attached may have a maximum drywall thickness of 5/8” (1.6 cm).
AVERTISSEMENT: Le défaut de fournir une résistance structurelle correcte pour le composant
peut entraîner des blessures graves ou endommager l'équipement. Le goujon de 2x4 auquel le
composant mur est connecté peut avoir un maximum de 1.6 cm (5/8”) d'Épaisseur cloison
sèche.
WARNING: Exceeding the weight capacity may result in personal injury or equipment damage.
The combined weight of all components attached to the mount must not exceed weights listed
on page 3.
AVERTISSEMENT: Dépasser la capacité de poids peut entraîner des blessures ou des dom-
mages matériels. Le poids combiné de tous les composants reliés au support de montage ne
doit pas dépasser les grammages indiqués à la page 3.
WARNING: Be aware of pinch points and do not place fingers in between moving parts.
AVERTISSEMENT: Soyez conscient des points de pincement et de ne pas placer les doigts
entre les pièces mobiles.
WARNING: Use this product for its intended use and only use attachments recommended by
the manufacturer.
AVERTISSEMENT: Utilisez ce produit pour son utilisation prévue et utiliser uniquement les
accessoires recommandés par le fabricant.
WARNING: Do not use a damaged product. Return damaged products to a qualified service
center for repair.
AVERTISSEMENT: Ne pas utiliser un produit endommagé. Retour produits endommagés à un
centre de service qualifié pour la réparation.
WARNING: Not intended for outdoor use.
AVERTISSEMENT: Non destiné à une utilisation en extérieur.
Page 2

Page 3
WEIGHT RATINGS
Model Weight Rating
VDM-600-M 100 lbs. Maximum Total Rated Load
VDM-800-M 150 lbs. Maximum Total Rated Load
REQUIRED TOOLS
• #2 Phillips Screwdriver
• Level
• Power Drill
• Protective Eyewear
• 3/16” Wood Bit or 3/8” Masonary Bit
• Hammer
• 10mm Socket
• Hex Wrench (Supplied)
• 4mm Hex Key (Supplied)
WARNING: Use tools with caution and follow all necessary safety protocols.
AVERTISSEMENT: Utiliser des outils avec prudence et suivre tous les protocoles de sécurité
nécessaires.
(1)
Display Mount
(A)
(1)
Template
(D)
(2)
Display Mount Bracket
(B)
SUPPLIED COMPONENTS
(2)
Mount Arm Cover
(C)

(1)
Hex Wrench
(E)
(6)
Hex Head Screw
(G)
(6)
Wall Anchor
(H)
(6)
Washer
(M)
(4)
Combo Washer
(J)
(8)
Small Spacer
(K)
(4)
Large Spacer
(L)
(1)
Hex Key
(F)
Page 4
SUPPLIED COMPONENTS (CONTINUED)
(4)
M4 x 20
(M-B)
M5 x 30
(M-D)
M6 x 20
(M-F)
M6 x 30
(M-G)
M5 x 12
(M-C)
(4) (4)
M6 x 12
(M-E)
(4) (4) (4)
M4 x 12
(M-A)
Display Mount Screws
M8 x 16
(M-H)
(4)
M8 x 20
(M-J)
(4)
(4) M8 x 40
(M-K)
(4)
(1)
Proximity Mounting
Plate Kit
(P)

1. Locate the stud center and adjacent stud center where you wish to locate your mount arm.
2. Use a level on top of supplied template (D) to mark 2 holes for each stud. (FIGURE B)
FIGURE A
FIGURE B
FIGURE C
3. Use a 3/16” (4.5 mm) bit to drill pilot holes into the markings to a 2.2” (55 mm) depth. (FIGURE C)
ø 4.5mm
(ø 3/16")
55mm
(2.2")
Page 5
REMOVING MONITOR MOUNT ARM FROM HORIZONTAL MONITOR SUPPORT
ATTACHING MOUNT ARM TO STUDS
A
E
D
Mark 4 Holes
1. Using supplied hex wrench (E), loosen the top 2 flange nuts and remove the bottom nut.
2. Tilt the bottom of display support out and slide up to remove from display arm as shown.
(FIGURE A)

1. Use a level on top of the supplied template (D) to mark 6 holes on the concrete where you wish to
locate your mount arm. (FIGURE E)
FIGURE D
FIGURE E
Page 6
FIGURE F
2. Use a 3/8” (10 mm) bit to drill pilot holes into the markings to a 2.4” (60 mm) depth. (FIGURE F)
60mm
(2.4")
ø 10mm
(ø 3/8")
4. Use (4x) hex head screws (G) and (4x) washers (M) to attach the mount arm to the stud wall as
shown. (FIGURE D)
ATTACHING MOUNT ARM TO STUDS (CONTINUED)
ATTACHING MOUNT ARM TO A CONCRETE WALL
Mark 6 Holes
G
MNOTE: Display mount
slots must face up.

FIGURE G
FIGURE H
FIGURE J
Page 7
3. Use (6x) wall anchors (H), (6x) hex head screws (G), and (4x) washers (M) to mount arm to the
wall as shown. (FIGURE G)
1. Attach (2x) mount arm covers (C) to the mount arm as shown. (FIGURE H)
1. Use a #2 Phillips screwdriver to remove the 4 screws on the ends of the horizontal support as
shown. (FIGURE J)
ATTACHING MOUNT ARM TO A CONCRETE WALL (CONTINUED)
ATTACHING MOUNT ARM COVERS TO THE MOUNT ARM
ATTACHING DISPLAY MOUNTING BRACKETS TO HORIZONTAL SUPPORTS
HG
M
C
NOTE: Wall anchors may
require a hammer
to install.
NOTE: To prevent anchors from
stripping, only use a hand
tool to install.

Page 8
STOP
The VDM-600-M & VDM-800-M display mounts are supplied with
a Proximity Series Mounting Plate PRX-MP-9X12.
Before installing display mounting brackets to your display,
follow the supplied mounting plate installation instructions I-00804
to find the best location for mounting your plate.

FIGURE K
FIGURE L
Page 9
2. Slide the (2x) display mounting brackets (B) onto the horizontal support as shown. (FIGURE K)
2. Reattach the 4 screws to the ends of the horizontal support as shown. (FIGURE L)
Attaching to a Flat Back Display
1. Use (4x) rectangular washers (J) and (4x) display mount screws (M-A through M-K) to match the
correct screw depth for your display and attach the mounting brackets to your display ensuring
screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance,
stop immediately and try a shorter screw. If supplied screws are still too long, use supplied spacers
to take up slack. (FIGURE M)
2. Tighten the screws on the lower ends of the mounting brackets as shown. (FIGURE M)
ATTACHING DISPLAY MOUNTING BRACKETS TO HORIZONTAL SUPPORT (CONT.)
ATTACHING MOUNTING BRACKETS TO DISPLAY
B
FIGURE M
J
M-A - M-K
12

Page 10
Attaching to a Recessed Back Display
1. Use (4x) rectangular washers (J), small and/or (4x) spacers (K) and (L) as desired, and
(4x) display mount screws (M-A - M-K) to match the correct screw depth for your display and
attach the mounting brackets to your display ensuring screw does not bottom out in mounting hole,
or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw.
If supplied screws are still too long, use supplied spacers to take up slack. (FIGURE P)
2. Tighten the screws on the lower ends of the mounting brackets as shown. (FIGURE P)
1. Carefully use the top bolts (with the flange nuts attached) to tilt and hook the horizontal display
support into the top slots on the end of the arm as shown. (FIGURE R)
ATTACHING MOUNTING BRACKETS TO DISPLAY (CONTINUED)
ATTACHING DISPLAY MOUNT ARM TO HORIZONTAL DISPLAY SUPPORT
FIGURE P
FIGURE R
J
K or L
M-A - M-K
K and L
M-A - M-K
J