Midland X-tra talk lxt500 series User manual

Welcome to the world of Midland electronics

Congratulations on your purchase of a high quality MIDLAND

product. Your 2-way radio represents state-of-the-art high-tech

engineering. Designed for GMRS (General Mobile Radio Service)

operation, this compact package is big on performance. It is a

quality piece of electronic equipment, skillfully constructed with the

finest components. The circuitry is all solid-state and mounted on a

rugged printed circuit board. Your two-way radio is designed for

reliable and trouble-free performance for years to come.

Features

- 22 GMRS/FRS Channel

- Call Alert

- Scan Function

- Roger Beep Tone

- Silent Operation

- Keypad Lock

- Power HI/LO Settings

- Auto Squelch

- Speaker / Microphone Jacks

- Battery Life Extender

- Battery Low Indicator

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device does not

cause harmful interference, and (2) this radio must accept any

interference that may cause undesired operation.

To maintain compliance with FCC’s RF exposure guidelines, for

body-worn operation, this radio has been tested and meets the

FCC RF exposure guidelines when used with Midland Radio

Corp. accessories supplied or designated for this product. Use of

other accessories may not ensure compliance with FCC RF

exposure guidelines.

IMPORTANT NOTICE, FCC LICENSE REQUIRED FOR GMRS OPERATION

(Only Applicable for GMRS Radio Use in the United States)

The radios operates on GMRS (General Mobile Radio Service) frequencies

which require an FCC (Federal Communications Commission) license. You must

be licensed prior to operating on channels 1 - 7 or 15 - 22, which comprise the

GMRS channels of the radios. Serious penalties could result from unlicensed use

of GMRS channels, in violation of FCC rules, as stipulated in the

Communications Acts Sections 501 and 502 (amended).

You will be issued a call sign by the FCC which should be used for station

identification when operating the radio on GMRS channels. You should also

cooperate by engaging in permissible transmissions only, avoiding channel

interference with other GMRS users, and being prudent with the length of your

transmission time.

To obtain a license or ask questions about the license application, contact the

FCC at 1-888-CALL FCC or go to the FCC's website:

http://www.fcc.gov and request form 605.

Exposure To Radio Frequency Energy

Your Midland radio is designed to comply with the following national and

international standards and guidelines regarding exposure of human beings to

radio frequency electromagnetic energy:

- United States Federal Communications Commission, Code of Federal

Regulations: 47 CFR part 2 sub-part J

- American National Standards Institute (ANSI)/Institute of Electrical &

Electronic Engineers (IEEE) C95. 1-1992

- Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1999 Edition

- National Council on Radiation Protection and Measurements (NCRP) of the

United States, Report 86, 1986

- International Commission on Non-lonizing Radiation Protection (ICNIRP)

1998

To control your exposure and ensure compliance with the general population or

uncontrolled environment exposure limits, transmit no more than 50% of the

time. The radio generates measurable RF energy exposure only when

transmitting.

IMPORTANT: Changes or modifications to this unit not expressly approved by

MIDLAND RADIO CORP. could void your right to operate this unit. Your radio

is set up to transmit a regulated signal on an assigned frequency. It is against

the law to alter or adjust the settings inside the COMMUNICATOR to exceed

those limitations. Any adjustment to your radio must be made by qualified

technicians.

LCD DISPLAY1. LOW BATTERY ICON – Indicates the

battery level is low.

2. TRANSMIT (TX) ICON – Indicates

radio is transmitting a signal.

3. CHANNEL NUMBER – Changes from

1~22 on GMRS/FRS band.

4. KEY LOCK ICON – Indicates KEY

LOCK mode is on.

5. RECEIVE (RX) ICON – Indicates

radio is receiving a transmission.

6. TRANSMIT POWER LEVEL ICON –

Indicates TX Power setting (H/L)

CONTROLS

7. PTT Button – Press and hold to

transmit voice communication.

8. CALL/LOCK Button – Press to send

a CALL Alert signal. Press and hold to

turn KEY LOCK on/off.

9. MIC – Built-in microphone.

10. SPEAKER – Built-in speaker.

11. ANTENNA

12. EXTERNAL SPEAKER/MIC/CHG.

JACK

13. POWER / MENU Button – Press and

hold for at least 3 seconds to turn the

radio on/off. Press momentarily to

access Menu mode.

14. SCAN Button – Press to enter SCAN

mode.

15. UP sand DOWN tButtons –

Make adjustments in MENU mode.

BATTERY INSTALLATION

Your radio operates with either a NiMH battery pack or optional 4 AAA

alkaline batteries. The belt clip should be removed to ease installation or

removal of the batteries.

To install the batteries:

1. With the back of the radio facing you, remove the belt clip (see

diagram on the next page) for easy access, then remove the Battery

Cover by pressing down on the top center and sliding it down from the

radio.

2. Insert 4 AAA batteries observing the polarity as shown. Installing

the batteries incorrectly will prevent the unit from operating or may

damage the unit.

3. Return the Battery Cover by sliding it up on the radio. Replace the

belt clip, making sure it locks into place.

MMIIDDLLAANNDDRRAADDIIOOCCOORRPPOORRAATTIIOONN

5900 Parretta Drive

Kansas City, MO 64120

Call 816.241.8500

We’d love to hear from you! Let us know what you

think of your new Midland product on

or by visiting us at

midlandusa.com

Note: Features & Specifications are subject to change without

notice. MIDLAND is not responsible for unintentional errors or

omissions on its packaging.

BATTERY

COMPARTMENT

BATTERY

COMPARTMENT

COVER

Press here and

push down to open

BELT CLIP

LOCK TAB

BELT CLIP

LATCH

INSTALLING THE BELT CLIP

To install the BELT CLIP, slide the clip up into the slot on the back of

the radio until the BELT CLIP LATCH clicks. To remove the BELT

CLIP, press the LOCK TAB up, then gently pull the belt clip down

toward the bottom of the radio.

CHARGING THE BATTERY PACK

Your radio is equipped to use a rechargeable NiMH battery pack

which can be recharged with the optional desktop charger (as

described below). The radio can also be charged by inserting the AC

adapter into the radio charge jack. Initial charge time is 24 hours.

Charge time is about 12 hours thereafter. For maximum battery life,

we recommend charging the battery pack when the low battery icon

comes on. Remove the radios from the charger when the charge time

expires.

To charge using a Desktop Charger:

1. Place the rechargeable battery packs in the radios.

2. Connect the AC adapter into an AC wall outlet.

3. Insert the AC adapter plug (or DC Cigarette Lighter adapter if

charging in vehicle) into the desktop charger jack.

4. Place the units into the desktop charger slot and note that the LED

indicator with RED color will light up, indicating charging function.

In order to ensure that the battery pack is fully charged, it is

recommended that the battery pack be charged for at least 12

hours with the radio turned OFF.

1. Only use our NiMH battery pack and AC adapter.

2. Do not attempt to charge alkaline batteries or any batteries

or battery packs other than the one indicated in the manual.

This may cause leakage and damage to the radio.

3. For long term storage of the radio, turn the radio OFF and

remove the batteries from the radio.

LOW BATTERY LEVEL INDICATOR

Your radio has a LOW BATTERY ICON which will only appear

on the LCD display if the battery voltage level is low.At this point, the

battery needs to be charged for at least 12 hrs.

POWER ON/OFF AND VOLUME

Press the POWER/MENU button for at least 3 seconds to turn the

radio on/off. During Power On, the radio will beep 3 times with

different tones, the LCD will display all icons for 1 second and the

LCD display will indicate the last channel selected.

To increase/decrease the volume level, press the s\tbuttons

during RX or STANDBY mode.

TRANSMITTING AND RECEIVING A CALL

To communicate, all radios in your group must be set to the same

channel.

1. For maximum clarity, hold the radio 2 to 3 inches from your mouth.

2. Press and hold the PTT button and speak in a normal voice

into the microphone. The TX icon will appear continuously on

the LCD display while transmitting.

3. To receive a call, release the PTT button. The RX icon will appear

on the display when your radio is receiving a transmission.

OPERATING YOUR RADIO

ABOUT RANGE

Your LXT Series radios are designed to give you maximum range

under optimum conditions.

Optimum Conditions are:

lOver water

lOpen rural areas without obstructions

lFlat areas where you can see the other person

To ensure you get maximum range:

lBe sure to use fresh or fully charged batteries - low batteries will

cause low power conditions.

lBe sure you are on a GMRS channel - FRS channels are

restricted by the FCC to low power.

lBe sure to set your radio to use Hi power.

LXT Series QUICK REFERENCE CHART

SCAN

Your radios can scan all 22 channels for activity. To enter, quickly

press the SCAN button. Repeat the same procedure to exit. Your

radio will rapidly scan each of the 22 channels and stop on any active

channel for 4 seconds before resuming scan.

When you press the PTT button to transmit on an active channel, the

scanning function will stop and remain on the active channel. To

resume scanning, quickly press the SCAN button.

MENU Channel

1~22

Roger Beep

On/Off

Power

H/L

Silent Operation

On/Off

Rev G

Welcome to the world of Midland electronics

Congratulations on your purchase of a high quality MIDLAND

product. Your 2-way radio represents state-of-the-art high-tech

engineering. Designed for GMRS (General Mobile Radio Service)

operation, this compact package is big on performance. It is a

quality piece of electronic equipment, skillfully constructed with the

finest components. The circuitry is all solid-state and mounted on a

rugged printed circuit board. Your two-way radio is designed for

reliable and trouble-free performance for years to come.

Features

- 22 GMRS/FRS Channel

- Call Alert

- Scan Function

- Roger Beep Tone

- Silent Operation

- Keypad Lock

- Power HI/LO Settings

- Auto Squelch

- Speaker / Microphone Jacks

- Battery Life Extender

- Battery Low Indicator

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device does not

cause harmful interference, and (2) this radio must accept any

interference that may cause undesired operation.

To maintain compliance with FCC’s RF exposure guidelines, for

body-worn operation, this radio has been tested and meets the

FCC RF exposure guidelines when used with Midland Radio

Corp. accessories supplied or designated for this product. Use of

other accessories may not ensure compliance with FCC RF

exposure guidelines.

IMPORTANT NOTICE, FCC LICENSE REQUIRED FOR GMRS OPERATION

(Only Applicable for GMRS Radio Use in the United States)

The radios operates on GMRS (General Mobile Radio Service) frequencies

which require an FCC (Federal Communications Commission) license. You must

be licensed prior to operating on channels 1 - 7 or 15 - 22, which comprise the

GMRS channels of the radios. Serious penalties could result from unlicensed use

of GMRS channels, in violation of FCC rules, as stipulated in the

Communications Acts Sections 501 and 502 (amended).

You will be issued a call sign by the FCC which should be used for station

identification when operating the radio on GMRS channels. You should also

cooperate by engaging in permissible transmissions only, avoiding channel

interference with other GMRS users, and being prudent with the length of your

transmission time.

To obtain a license or ask questions about the license application, contact the

FCC at 1-888-CALL FCC or go to the FCC's website:

http://www.fcc.gov and request form 605.

Exposure To Radio Frequency Energy

Your Midland radio is designed to comply with the following national and

international standards and guidelines regarding exposure of human beings to

radio frequency electromagnetic energy:

- United States Federal Communications Commission, Code of Federal

Regulations: 47 CFR part 2 sub-part J

- American National Standards Institute (ANSI)/Institute of Electrical &

Electronic Engineers (IEEE) C95. 1-1992

- Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1999 Edition

- National Council on Radiation Protection and Measurements (NCRP) of the

United States, Report 86, 1986

- International Commission on Non-lonizing Radiation Protection (ICNIRP)

1998

To control your exposure and ensure compliance with the general population or

uncontrolled environment exposure limits, transmit no more than 50% of the

time. The radio generates measurable RF energy exposure only when

transmitting.

IMPORTANT: Changes or modifications to this unit not expressly approved by

MIDLAND RADIO CORP. could void your right to operate this unit. Your radio

is set up to transmit a regulated signal on an assigned frequency. It is against

the law to alter or adjust the settings inside the COMMUNICATOR to exceed

those limitations. Any adjustment to your radio must be made by qualified

technicians.

LCD DISPLAY1. LOW BATTERY ICON – Indicates the

battery level is low.

2. TRANSMIT (TX) ICON – Indicates

radio is transmitting a signal.

3. CHANNEL NUMBER – Changes from

1~22 on GMRS/FRS band.

4. KEY LOCK ICON – Indicates KEY

LOCK mode is on.

5. RECEIVE (RX) ICON – Indicates

radio is receiving a transmission.

6. TRANSMIT POWER LEVEL ICON –

Indicates TX Power setting (H/L)

CONTROLS

7. PTT Button – Press and hold to

transmit voice communication.

8. CALL/LOCK Button – Press to send

a CALL Alert signal. Press and hold to

turn KEY LOCK on/off.

9. MIC – Built-in microphone.

10. SPEAKER – Built-in speaker.

11. ANTENNA

12. EXTERNAL SPEAKER/MIC/CHG.

JACK

13. POWER / MENU Button – Press and

hold for at least 3 seconds to turn the

radio on/off. Press momentarily to

access Menu mode.

14. SCAN Button – Press to enter SCAN

mode.

15. UP sand DOWN tButtons –

Make adjustments in MENU mode.

BATTERY INSTALLATION

Your radio operates with either a NiMH battery pack or optional 4 AAA

alkaline batteries. The belt clip should be removed to ease installation or

removal of the batteries.

To install the batteries:

1. With the back of the radio facing you, remove the belt clip (see

diagram on the next page) for easy access, then remove the Battery

Cover by pressing down on the top center and sliding it down from the

radio.

2. Insert 4 AAA batteries observing the polarity as shown. Installing

the batteries incorrectly will prevent the unit from operating or may

damage the unit.

3. Return the Battery Cover by sliding it up on the radio. Replace the

belt clip, making sure it locks into place.

MMIIDDLLAANNDDRRAADDIIOOCCOORRPPOORRAATTIIOONN

5900 Parretta Drive

Kansas City, MO 64120

Call 816.241.8500

We’d love to hear from you! Let us know what you

think of your new Midland product on

or by visiting us at

midlandusa.com

Note: Features & Specifications are subject to change without

notice. MIDLAND is not responsible for unintentional errors or

omissions on its packaging.

BATTERY

COMPARTMENT

BATTERY

COMPARTMENT

COVER

Press here and

push down to open

BELT CLIP

LOCK TAB

BELT CLIP

LATCH

INSTALLING THE BELT CLIP

To install the BELT CLIP, slide the clip up into the slot on the back of

the radio until the BELT CLIP LATCH clicks. To remove the BELT

CLIP, press the LOCK TAB up, then gently pull the belt clip down

toward the bottom of the radio.

CHARGING THE BATTERY PACK

Your radio is equipped to use a rechargeable NiMH battery pack

which can be recharged with the optional desktop charger (as

described below). The radio can also be charged by inserting the AC

adapter into the radio charge jack. Initial charge time is 24 hours.

Charge time is about 12 hours thereafter. For maximum battery life,

we recommend charging the battery pack when the low battery icon

comes on. Remove the radios from the charger when the charge time

expires.

To charge using a Desktop Charger:

1. Place the rechargeable battery packs in the radios.

2. Connect the AC adapter into an AC wall outlet.

3. Insert the AC adapter plug (or DC Cigarette Lighter adapter if

charging in vehicle) into the desktop charger jack.

4. Place the units into the desktop charger slot and note that the LED

indicator with RED color will light up, indicating charging function.

In order to ensure that the battery pack is fully charged, it is

recommended that the battery pack be charged for at least 12

hours with the radio turned OFF.

1. Only use our NiMH battery pack and AC adapter.

2. Do not attempt to charge alkaline batteries or any batteries

or battery packs other than the one indicated in the manual.

This may cause leakage and damage to the radio.

3. For long term storage of the radio, turn the radio OFF and

remove the batteries from the radio.

LOW BATTERY LEVEL INDICATOR

Your radio has a LOW BATTERY ICON which will only appear

on the LCD display if the battery voltage level is low.At this point, the

battery needs to be charged for at least 12 hrs.

POWER ON/OFF AND VOLUME

Press the POWER/MENU button for at least 3 seconds to turn the

radio on/off. During Power On, the radio will beep 3 times with

different tones, the LCD will display all icons for 1 second and the

LCD display will indicate the last channel selected.

To increase/decrease the volume level, press the s\tbuttons

during RX or STANDBY mode.

TRANSMITTING AND RECEIVING A CALL

To communicate, all radios in your group must be set to the same

channel.

1. For maximum clarity, hold the radio 2 to 3 inches from your mouth.

2. Press and hold the PTT button and speak in a normal voice

into the microphone. The TX icon will appear continuously on

the LCD display while transmitting.

3. To receive a call, release the PTT button. The RX icon will appear

on the display when your radio is receiving a transmission.

OPERATING YOUR RADIO

ABOUT RANGE

Your LXT Series radios are designed to give you maximum range

under optimum conditions.

Optimum Conditions are:

lOver water

lOpen rural areas without obstructions

lFlat areas where you can see the other person

To ensure you get maximum range:

lBe sure to use fresh or fully charged batteries - low batteries will

cause low power conditions.

lBe sure you are on a GMRS channel - FRS channels are

restricted by the FCC to low power.

lBe sure to set your radio to use Hi power.

LXT Series QUICK REFERENCE CHART

SCAN

Your radios can scan all 22 channels for activity. To enter, quickly

press the SCAN button. Repeat the same procedure to exit. Your

radio will rapidly scan each of the 22 channels and stop on any active

channel for 4 seconds before resuming scan.

When you press the PTT button to transmit on an active channel, the

scanning function will stop and remain on the active channel. To

resume scanning, quickly press the SCAN button.

MENU Channel

1~22

Roger Beep

On/Off

Power

H/L

Silent Operation

On/Off

Rev G

Welcome to the world of Midland electronics

Congratulations on your purchase of a high quality MIDLAND

product. Your 2-way radio represents state-of-the-art high-tech

engineering. Designed for GMRS (General Mobile Radio Service)

operation, this compact package is big on performance. It is a

quality piece of electronic equipment, skillfully constructed with the

finest components. The circuitry is all solid-state and mounted on a

rugged printed circuit board. Your two-way radio is designed for

reliable and trouble-free performance for years to come.

Features

- 22 GMRS/FRS Channel

- Call Alert

- Scan Function

- Roger Beep Tone

- Silent Operation

- Keypad Lock

- Power HI/LO Settings

- Auto Squelch

- Speaker / Microphone Jacks

- Battery Life Extender

- Battery Low Indicator

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device does not

cause harmful interference, and (2) this radio must accept any

interference that may cause undesired operation.

To maintain compliance with FCC’s RF exposure guidelines, for

body-worn operation, this radio has been tested and meets the

FCC RF exposure guidelines when used with Midland Radio

Corp. accessories supplied or designated for this product. Use of

other accessories may not ensure compliance with FCC RF

exposure guidelines.

IMPORTANT NOTICE, FCC LICENSE REQUIRED FOR GMRS OPERATION

(Only Applicable for GMRS Radio Use in the United States)

The radios operates on GMRS (General Mobile Radio Service) frequencies

which require an FCC (Federal Communications Commission) license. You must

be licensed prior to operating on channels 1 - 7 or 15 - 22, which comprise the

GMRS channels of the radios. Serious penalties could result from unlicensed use

of GMRS channels, in violation of FCC rules, as stipulated in the

Communications Acts Sections 501 and 502 (amended).

You will be issued a call sign by the FCC which should be used for station

identification when operating the radio on GMRS channels. You should also

cooperate by engaging in permissible transmissions only, avoiding channel

interference with other GMRS users, and being prudent with the length of your

transmission time.

To obtain a license or ask questions about the license application, contact the

FCC at 1-888-CALL FCC or go to the FCC's website:

http://www.fcc.gov and request form 605.

Exposure To Radio Frequency Energy

Your Midland radio is designed to comply with the following national and

international standards and guidelines regarding exposure of human beings to

radio frequency electromagnetic energy:

- United States Federal Communications Commission, Code of Federal

Regulations: 47 CFR part 2 sub-part J

- American National Standards Institute (ANSI)/Institute of Electrical &

Electronic Engineers (IEEE) C95. 1-1992

- Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1999 Edition

- National Council on Radiation Protection and Measurements (NCRP) of the

United States, Report 86, 1986

- International Commission on Non-lonizing Radiation Protection (ICNIRP)

1998

To control your exposure and ensure compliance with the general population or

uncontrolled environment exposure limits, transmit no more than 50% of the

time. The radio generates measurable RF energy exposure only when

transmitting.

IMPORTANT: Changes or modifications to this unit not expressly approved by

MIDLAND RADIO CORP. could void your right to operate this unit. Your radio

is set up to transmit a regulated signal on an assigned frequency. It is against

the law to alter or adjust the settings inside the COMMUNICATOR to exceed

those limitations. Any adjustment to your radio must be made by qualified

technicians.

LCD DISPLAY1. LOW BATTERY ICON – Indicates the

battery level is low.

2. TRANSMIT (TX) ICON – Indicates

radio is transmitting a signal.

3. CHANNEL NUMBER – Changes from

1~22 on GMRS/FRS band.

4. KEY LOCK ICON – Indicates KEY

LOCK mode is on.

5. RECEIVE (RX) ICON – Indicates

radio is receiving a transmission.

6. TRANSMIT POWER LEVEL ICON –

Indicates TX Power setting (H/L)

CONTROLS

7. PTT Button – Press and hold to

transmit voice communication.

8. CALL/LOCK Button – Press to send

a CALL Alert signal. Press and hold to

turn KEY LOCK on/off.

9. MIC – Built-in microphone.

10. SPEAKER – Built-in speaker.

11. ANTENNA

12. EXTERNAL SPEAKER/MIC/CHG.

JACK

13. POWER / MENU Button – Press and

hold for at least 3 seconds to turn the

radio on/off. Press momentarily to

access Menu mode.

14. SCAN Button – Press to enter SCAN

mode.

15. UP sand DOWN tButtons –

Make adjustments in MENU mode.

BATTERY INSTALLATION

Your radio operates with either a NiMH battery pack or optional 4 AAA

alkaline batteries. The belt clip should be removed to ease installation or

removal of the batteries.

To install the batteries:

1. With the back of the radio facing you, remove the belt clip (see

diagram on the next page) for easy access, then remove the Battery

Cover by pressing down on the top center and sliding it down from the

radio.

2. Insert 4 AAA batteries observing the polarity as shown. Installing

the batteries incorrectly will prevent the unit from operating or may

damage the unit.

3. Return the Battery Cover by sliding it up on the radio. Replace the

belt clip, making sure it locks into place.

MMIIDDLLAANNDDRRAADDIIOOCCOORRPPOORRAATTIIOONN

5900 Parretta Drive

Kansas City, MO 64120

Call 816.241.8500

We’d love to hear from you! Let us know what you

think of your new Midland product on

or by visiting us at

midlandusa.com

Note: Features & Specifications are subject to change without

notice. MIDLAND is not responsible for unintentional errors or

omissions on its packaging.

BATTERY

COMPARTMENT

BATTERY

COMPARTMENT

COVER

Press here and

push down to open

BELT CLIP

LOCK TAB

BELT CLIP

LATCH

INSTALLING THE BELT CLIP

To install the BELT CLIP, slide the clip up into the slot on the back of

the radio until the BELT CLIP LATCH clicks. To remove the BELT

CLIP, press the LOCK TAB up, then gently pull the belt clip down

toward the bottom of the radio.

CHARGING THE BATTERY PACK

Your radio is equipped to use a rechargeable NiMH battery pack

which can be recharged with the optional desktop charger (as

described below). The radio can also be charged by inserting the AC

adapter into the radio charge jack. Initial charge time is 24 hours.

Charge time is about 12 hours thereafter. For maximum battery life,

we recommend charging the battery pack when the low battery icon

comes on. Remove the radios from the charger when the charge time

expires.

To charge using a Desktop Charger:

1. Place the rechargeable battery packs in the radios.

2. Connect the AC adapter into an AC wall outlet.

3. Insert the AC adapter plug (or DC Cigarette Lighter adapter if

charging in vehicle) into the desktop charger jack.

4. Place the units into the desktop charger slot and note that the LED

indicator with RED color will light up, indicating charging function.

In order to ensure that the battery pack is fully charged, it is

recommended that the battery pack be charged for at least 12

hours with the radio turned OFF.

1. Only use our NiMH battery pack and AC adapter.

2. Do not attempt to charge alkaline batteries or any batteries

or battery packs other than the one indicated in the manual.

This may cause leakage and damage to the radio.

3. For long term storage of the radio, turn the radio OFF and

remove the batteries from the radio.

LOW BATTERY LEVEL INDICATOR

Your radio has a LOW BATTERY ICON which will only appear

on the LCD display if the battery voltage level is low.At this point, the

battery needs to be charged for at least 12 hrs.

POWER ON/OFF AND VOLUME

Press the POWER/MENU button for at least 3 seconds to turn the

radio on/off. During Power On, the radio will beep 3 times with

different tones, the LCD will display all icons for 1 second and the

LCD display will indicate the last channel selected.

To increase/decrease the volume level, press the s\tbuttons

during RX or STANDBY mode.

TRANSMITTING AND RECEIVING A CALL

To communicate, all radios in your group must be set to the same

channel.

1. For maximum clarity, hold the radio 2 to 3 inches from your mouth.

2. Press and hold the PTT button and speak in a normal voice

into the microphone. The TX icon will appear continuously on

the LCD display while transmitting.

3. To receive a call, release the PTT button. The RX icon will appear

on the display when your radio is receiving a transmission.

OPERATING YOUR RADIO

ABOUT RANGE

Your LXT Series radios are designed to give you maximum range

under optimum conditions.

Optimum Conditions are:

lOver water

lOpen rural areas without obstructions

lFlat areas where you can see the other person

To ensure you get maximum range:

lBe sure to use fresh or fully charged batteries - low batteries will

cause low power conditions.

lBe sure you are on a GMRS channel - FRS channels are

restricted by the FCC to low power.

lBe sure to set your radio to use Hi power.

LXT Series QUICK REFERENCE CHART

SCAN

Your radios can scan all 22 channels for activity. To enter, quickly

press the SCAN button. Repeat the same procedure to exit. Your

radio will rapidly scan each of the 22 channels and stop on any active

channel for 4 seconds before resuming scan.

When you press the PTT button to transmit on an active channel, the

scanning function will stop and remain on the active channel. To

resume scanning, quickly press the SCAN button.

MENU Channel

1~22

Roger Beep

On/Off

Power

H/L

Silent Operation

On/Off

Rev G

Welcome to the world of Midland electronics

Congratulations on your purchase of a high quality MIDLAND

product. Your 2-way radio represents state-of-the-art high-tech

engineering. Designed for GMRS (General Mobile Radio Service)

operation, this compact package is big on performance. It is a

quality piece of electronic equipment, skillfully constructed with the

finest components. The circuitry is all solid-state and mounted on a

rugged printed circuit board. Your two-way radio is designed for

reliable and trouble-free performance for years to come.

Features

- 22 GMRS/FRS Channel

- Call Alert

- Scan Function

- Roger Beep Tone

- Silent Operation

- Keypad Lock

- Power HI/LO Settings

- Auto Squelch

- Speaker / Microphone Jacks

- Battery Life Extender

- Battery Low Indicator

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device does not

cause harmful interference, and (2) this radio must accept any

interference that may cause undesired operation.

To maintain compliance with FCC’s RF exposure guidelines, for

body-worn operation, this radio has been tested and meets the

FCC RF exposure guidelines when used with Midland Radio

Corp. accessories supplied or designated for this product. Use of

other accessories may not ensure compliance with FCC RF

exposure guidelines.

IMPORTANT NOTICE, FCC LICENSE REQUIRED FOR GMRS OPERATION

(Only Applicable for GMRS Radio Use in the United States)

The radios operates on GMRS (General Mobile Radio Service) frequencies

which require an FCC (Federal Communications Commission) license. You must

be licensed prior to operating on channels 1 - 7 or 15 - 22, which comprise the

GMRS channels of the radios. Serious penalties could result from unlicensed use

of GMRS channels, in violation of FCC rules, as stipulated in the

Communications Acts Sections 501 and 502 (amended).

You will be issued a call sign by the FCC which should be used for station

identification when operating the radio on GMRS channels. You should also

cooperate by engaging in permissible transmissions only, avoiding channel

interference with other GMRS users, and being prudent with the length of your

transmission time.

To obtain a license or ask questions about the license application, contact the

FCC at 1-888-CALL FCC or go to the FCC's website:

http://www.fcc.gov and request form 605.

Exposure To Radio Frequency Energy

Your Midland radio is designed to comply with the following national and

international standards and guidelines regarding exposure of human beings to

radio frequency electromagnetic energy:

- United States Federal Communications Commission, Code of Federal

Regulations: 47 CFR part 2 sub-part J

- American National Standards Institute (ANSI)/Institute of Electrical &

Electronic Engineers (IEEE) C95. 1-1992

- Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1999 Edition

- National Council on Radiation Protection and Measurements (NCRP) of the

United States, Report 86, 1986

- International Commission on Non-lonizing Radiation Protection (ICNIRP)

1998

To control your exposure and ensure compliance with the general population or

uncontrolled environment exposure limits, transmit no more than 50% of the

time. The radio generates measurable RF energy exposure only when

transmitting.

IMPORTANT: Changes or modifications to this unit not expressly approved by

MIDLAND RADIO CORP. could void your right to operate this unit. Your radio

is set up to transmit a regulated signal on an assigned frequency. It is against

the law to alter or adjust the settings inside the COMMUNICATOR to exceed

those limitations. Any adjustment to your radio must be made by qualified

technicians.

LCD DISPLAY1. LOW BATTERY ICON – Indicates the

battery level is low.

2. TRANSMIT (TX) ICON – Indicates

radio is transmitting a signal.

3. CHANNEL NUMBER – Changes from

1~22 on GMRS/FRS band.

4. KEY LOCK ICON – Indicates KEY

LOCK mode is on.

5. RECEIVE (RX) ICON – Indicates

radio is receiving a transmission.

6. TRANSMIT POWER LEVEL ICON –

Indicates TX Power setting (H/L)

CONTROLS

7. PTT Button – Press and hold to

transmit voice communication.

8. CALL/LOCK Button – Press to send

a CALL Alert signal. Press and hold to

turn KEY LOCK on/off.

9. MIC – Built-in microphone.

10. SPEAKER – Built-in speaker.

11. ANTENNA

12. EXTERNAL SPEAKER/MIC/CHG.

JACK

13. POWER / MENU Button – Press and

hold for at least 3 seconds to turn the

radio on/off. Press momentarily to

access Menu mode.

14. SCAN Button – Press to enter SCAN

mode.

15. UP sand DOWN tButtons –

Make adjustments in MENU mode.

BATTERY INSTALLATION

Your radio operates with either a NiMH battery pack or optional 4 AAA

alkaline batteries. The belt clip should be removed to ease installation or

removal of the batteries.

To install the batteries:

1. With the back of the radio facing you, remove the belt clip (see

diagram on the next page) for easy access, then remove the Battery

Cover by pressing down on the top center and sliding it down from the

radio.

2. Insert 4 AAA batteries observing the polarity as shown. Installing

the batteries incorrectly will prevent the unit from operating or may

damage the unit.

3. Return the Battery Cover by sliding it up on the radio. Replace the

belt clip, making sure it locks into place.

MMIIDDLLAANNDDRRAADDIIOOCCOORRPPOORRAATTIIOONN

5900 Parretta Drive

Kansas City, MO 64120

Call 816.241.8500

We’d love to hear from you! Let us know what you

think of your new Midland product on

or by visiting us at

midlandusa.com

Note: Features & Specifications are subject to change without

notice. MIDLAND is not responsible for unintentional errors or

omissions on its packaging.

BATTERY

COMPARTMENT

BATTERY

COMPARTMENT

COVER

Press here and

push down to open

BELT CLIP

LOCK TAB

BELT CLIP

LATCH

INSTALLING THE BELT CLIP

To install the BELT CLIP, slide the clip up into the slot on the back of

the radio until the BELT CLIP LATCH clicks. To remove the BELT

CLIP, press the LOCK TAB up, then gently pull the belt clip down

toward the bottom of the radio.

CHARGING THE BATTERY PACK

Your radio is equipped to use a rechargeable NiMH battery pack

which can be recharged with the optional desktop charger (as

described below). The radio can also be charged by inserting the AC

adapter into the radio charge jack. Initial charge time is 24 hours.

Charge time is about 12 hours thereafter. For maximum battery life,

we recommend charging the battery pack when the low battery icon

comes on. Remove the radios from the charger when the charge time

expires.

To charge using a Desktop Charger:

1. Place the rechargeable battery packs in the radios.

2. Connect the AC adapter into an AC wall outlet.

3. Insert the AC adapter plug (or DC Cigarette Lighter adapter if

charging in vehicle) into the desktop charger jack.

4. Place the units into the desktop charger slot and note that the LED

indicator with RED color will light up, indicating charging function.

In order to ensure that the battery pack is fully charged, it is

recommended that the battery pack be charged for at least 12

hours with the radio turned OFF.

1. Only use our NiMH battery pack and AC adapter.

2. Do not attempt to charge alkaline batteries or any batteries

or battery packs other than the one indicated in the manual.

This may cause leakage and damage to the radio.

3. For long term storage of the radio, turn the radio OFF and

remove the batteries from the radio.

LOW BATTERY LEVEL INDICATOR

Your radio has a LOW BATTERY ICON which will only appear

on the LCD display if the battery voltage level is low.At this point, the

battery needs to be charged for at least 12 hrs.

POWER ON/OFF AND VOLUME

Press the POWER/MENU button for at least 3 seconds to turn the

radio on/off. During Power On, the radio will beep 3 times with

different tones, the LCD will display all icons for 1 second and the

LCD display will indicate the last channel selected.

To increase/decrease the volume level, press the s\tbuttons

during RX or STANDBY mode.

TRANSMITTING AND RECEIVING A CALL

To communicate, all radios in your group must be set to the same

channel.

1. For maximum clarity, hold the radio 2 to 3 inches from your mouth.

2. Press and hold the PTT button and speak in a normal voice

into the microphone. The TX icon will appear continuously on

the LCD display while transmitting.

3. To receive a call, release the PTT button. The RX icon will appear

on the display when your radio is receiving a transmission.

OPERATING YOUR RADIO

ABOUT RANGE

Your LXT Series radios are designed to give you maximum range

under optimum conditions.

Optimum Conditions are:

lOver water

lOpen rural areas without obstructions

lFlat areas where you can see the other person

To ensure you get maximum range:

lBe sure to use fresh or fully charged batteries - low batteries will

cause low power conditions.

lBe sure you are on a GMRS channel - FRS channels are

restricted by the FCC to low power.

lBe sure to set your radio to use Hi power.

LXT Series QUICK REFERENCE CHART

SCAN

Your radios can scan all 22 channels for activity. To enter, quickly

press the SCAN button. Repeat the same procedure to exit. Your

radio will rapidly scan each of the 22 channels and stop on any active

channel for 4 seconds before resuming scan.

When you press the PTT button to transmit on an active channel, the

scanning function will stop and remain on the active channel. To

resume scanning, quickly press the SCAN button.

MENU Channel

1~22

Roger Beep

On/Off

Power

H/L

Silent Operation

On/Off

Rev G

Welcome to the world of Midland electronics

Congratulations on your purchase of a high quality MIDLAND

product. Your 2-way radio represents state-of-the-art high-tech

engineering. Designed for GMRS (General Mobile Radio Service)

operation, this compact package is big on performance. It is a

quality piece of electronic equipment, skillfully constructed with the

finest components. The circuitry is all solid-state and mounted on a

rugged printed circuit board. Your two-way radio is designed for

reliable and trouble-free performance for years to come.

Features

- 22 GMRS/FRS Channel

- Call Alert

- Scan Function

- Roger Beep Tone

- Silent Operation

- Keypad Lock

- Power HI/LO Settings

- Auto Squelch

- Speaker / Microphone Jacks

- Battery Life Extender

- Battery Low Indicator

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device does not

cause harmful interference, and (2) this radio must accept any

interference that may cause undesired operation.

To maintain compliance with FCC’s RF exposure guidelines, for

body-worn operation, this radio has been tested and meets the

FCC RF exposure guidelines when used with Midland Radio

Corp. accessories supplied or designated for this product. Use of

other accessories may not ensure compliance with FCC RF

exposure guidelines.

IMPORTANT NOTICE, FCC LICENSE REQUIRED FOR GMRS OPERATION

(Only Applicable for GMRS Radio Use in the United States)

The radios operates on GMRS (General Mobile Radio Service) frequencies

which require an FCC (Federal Communications Commission) license. You must

be licensed prior to operating on channels 1 - 7 or 15 - 22, which comprise the

GMRS channels of the radios. Serious penalties could result from unlicensed use

of GMRS channels, in violation of FCC rules, as stipulated in the

Communications Acts Sections 501 and 502 (amended).

You will be issued a call sign by the FCC which should be used for station

identification when operating the radio on GMRS channels. You should also

cooperate by engaging in permissible transmissions only, avoiding channel

interference with other GMRS users, and being prudent with the length of your

transmission time.

To obtain a license or ask questions about the license application, contact the

FCC at 1-888-CALL FCC or go to the FCC's website:

http://www.fcc.gov and request form 605.

Exposure To Radio Frequency Energy

Your Midland radio is designed to comply with the following national and

international standards and guidelines regarding exposure of human beings to

radio frequency electromagnetic energy:

- United States Federal Communications Commission, Code of Federal

Regulations: 47 CFR part 2 sub-part J

- American National Standards Institute (ANSI)/Institute of Electrical &

Electronic Engineers (IEEE) C95. 1-1992

- Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1999 Edition

- National Council on Radiation Protection and Measurements (NCRP) of the

United States, Report 86, 1986

- International Commission on Non-lonizing Radiation Protection (ICNIRP)

1998

To control your exposure and ensure compliance with the general population or

uncontrolled environment exposure limits, transmit no more than 50% of the

time. The radio generates measurable RF energy exposure only when

transmitting.

IMPORTANT: Changes or modifications to this unit not expressly approved by

MIDLAND RADIO CORP. could void your right to operate this unit. Your radio

is set up to transmit a regulated signal on an assigned frequency. It is against

the law to alter or adjust the settings inside the COMMUNICATOR to exceed

those limitations. Any adjustment to your radio must be made by qualified

technicians.

LCD DISPLAY1. LOW BATTERY ICON – Indicates the

battery level is low.

2. TRANSMIT (TX) ICON – Indicates

radio is transmitting a signal.

3. CHANNEL NUMBER – Changes from

1~22 on GMRS/FRS band.

4. KEY LOCK ICON – Indicates KEY

LOCK mode is on.

5. RECEIVE (RX) ICON – Indicates

radio is receiving a transmission.

6. TRANSMIT POWER LEVEL ICON –

Indicates TX Power setting (H/L)

CONTROLS

7. PTT Button – Press and hold to

transmit voice communication.

8. CALL/LOCK Button – Press to send

a CALL Alert signal. Press and hold to

turn KEY LOCK on/off.

9. MIC – Built-in microphone.

10. SPEAKER – Built-in speaker.

11. ANTENNA

12. EXTERNAL SPEAKER/MIC/CHG.

JACK

13. POWER / MENU Button – Press and

hold for at least 3 seconds to turn the

radio on/off. Press momentarily to

access Menu mode.

14. SCAN Button – Press to enter SCAN

mode.

15. UP sand DOWN tButtons –

Make adjustments in MENU mode.

BATTERY INSTALLATION

Your radio operates with either a NiMH battery pack or optional 4 AAA

alkaline batteries. The belt clip should be removed to ease installation or

removal of the batteries.

To install the batteries:

1. With the back of the radio facing you, remove the belt clip (see

diagram on the next page) for easy access, then remove the Battery

Cover by pressing down on the top center and sliding it down from the

radio.

2. Insert 4 AAA batteries observing the polarity as shown. Installing

the batteries incorrectly will prevent the unit from operating or may

damage the unit.

3. Return the Battery Cover by sliding it up on the radio. Replace the

belt clip, making sure it locks into place.

MMIIDDLLAANNDDRRAADDIIOOCCOORRPPOORRAATTIIOONN

5900 Parretta Drive

Kansas City, MO 64120

Call 816.241.8500

We’d love to hear from you! Let us know what you

think of your new Midland product on

or by visiting us at

midlandusa.com

Note: Features & Specifications are subject to change without

notice. MIDLAND is not responsible for unintentional errors or

omissions on its packaging.

BATTERY

COMPARTMENT

BATTERY

COMPARTMENT

COVER

Press here and

push down to open

BELT CLIP

LOCK TAB

BELT CLIP

LATCH

INSTALLING THE BELT CLIP

To install the BELT CLIP, slide the clip up into the slot on the back of

the radio until the BELT CLIP LATCH clicks. To remove the BELT

CLIP, press the LOCK TAB up, then gently pull the belt clip down

toward the bottom of the radio.

CHARGING THE BATTERY PACK

Your radio is equipped to use a rechargeable NiMH battery pack

which can be recharged with the optional desktop charger (as

described below). The radio can also be charged by inserting the AC

adapter into the radio charge jack. Initial charge time is 24 hours.

Charge time is about 12 hours thereafter. For maximum battery life,

we recommend charging the battery pack when the low battery icon

comes on. Remove the radios from the charger when the charge time

expires.

To charge using a Desktop Charger:

1. Place the rechargeable battery packs in the radios.

2. Connect the AC adapter into an AC wall outlet.

3. Insert the AC adapter plug (or DC Cigarette Lighter adapter if

charging in vehicle) into the desktop charger jack.

4. Place the units into the desktop charger slot and note that the LED

indicator with RED color will light up, indicating charging function.

In order to ensure that the battery pack is fully charged, it is

recommended that the battery pack be charged for at least 12

hours with the radio turned OFF.

1. Only use our NiMH battery pack and AC adapter.

2. Do not attempt to charge alkaline batteries or any batteries

or battery packs other than the one indicated in the manual.

This may cause leakage and damage to the radio.

3. For long term storage of the radio, turn the radio OFF and

remove the batteries from the radio.

LOW BATTERY LEVEL INDICATOR

Your radio has a LOW BATTERY ICON which will only appear

on the LCD display if the battery voltage level is low.At this point, the

battery needs to be charged for at least 12 hrs.

POWER ON/OFF AND VOLUME

Press the POWER/MENU button for at least 3 seconds to turn the

radio on/off. During Power On, the radio will beep 3 times with

different tones, the LCD will display all icons for 1 second and the

LCD display will indicate the last channel selected.

To increase/decrease the volume level, press the s\tbuttons

during RX or STANDBY mode.

TRANSMITTING AND RECEIVING A CALL

To communicate, all radios in your group must be set to the same

channel.

1. For maximum clarity, hold the radio 2 to 3 inches from your mouth.

2. Press and hold the PTT button and speak in a normal voice

into the microphone. The TX icon will appear continuously on

the LCD display while transmitting.

3. To receive a call, release the PTT button. The RX icon will appear

on the display when your radio is receiving a transmission.

OPERATING YOUR RADIO

ABOUT RANGE

Your LXT Series radios are designed to give you maximum range

under optimum conditions.

Optimum Conditions are:

lOver water

lOpen rural areas without obstructions

lFlat areas where you can see the other person

To ensure you get maximum range:

lBe sure to use fresh or fully charged batteries - low batteries will

cause low power conditions.

lBe sure you are on a GMRS channel - FRS channels are

restricted by the FCC to low power.

lBe sure to set your radio to use Hi power.

LXT Series QUICK REFERENCE CHART

SCAN

Your radios can scan all 22 channels for activity. To enter, quickly

press the SCAN button. Repeat the same procedure to exit. Your

radio will rapidly scan each of the 22 channels and stop on any active

channel for 4 seconds before resuming scan.

When you press the PTT button to transmit on an active channel, the

scanning function will stop and remain on the active channel. To

resume scanning, quickly press the SCAN button.

MENU Channel

1~22

Roger Beep

On/Off

Power

H/L

Silent Operation

On/Off

Rev G

CALL ALERT

Your radios can transmit a call alert for a fixed length of time. To send

a call alert, press the CALL button. The TX icon will appear while

transmitting a call alert and a tone can be heard on the speaker for

confirmation.

KEYPAD LOCK

To avoid accidentally changing the radio setting, press the LOCK

button for 4 seconds. The KEY LOCK icon will appear on the display.

PTT and CALL will still be active. Repeat the same procedure to

unlock the keypad.

CHANNEL SELECTION (GMRS/FRS BAND)

Press the MENU button once, and then the s\tbuttons to select

one of the 22 GMRS/FRS channels. To confirm the selection, press

the PTT button or press the MENU button again to move to the next

feature setting.

Note : To communicate between two radios, all radios in your

group must be set to the same channel.

TRANSMIT (TX) POWER LEVEL SELECTION

Your radio has 2 power level settings. To select the power level on

channels 1~7 and 15~22, press the MENU button until a “Pr” icon

appears blinking on the display. Then press the s\tbuttons to

select TRANSMIT POWER LEVEL icon (H: Hi/L: Lo). To confirm,

press the PTT button or press the MENU button again to move to the

next feature setting.

Note : You cannot adjust the power setting on the FRS

channels (8~14). They are set to Lo power per

FCC regulations.

ROGER BEEP (end of transmission) TONE

When the PTT button is released, the radio will beep to confirm to

other users that your transmission has finished.

To turn the ROGER BEEP tone on, press the MENU button until the

display shows a “rb” icon while on the right of the “rb” display, an “oF”

icon appears. Select “on” by pressing the s\tbuttons and push the

PTT key, or press the MENU button to move to the next feature

setting.

To turn the ROGER BEEP tone off, press the MENU button until the

display shows a “rb” icon while on the right of the “rb” display, an “on”

icon appears. Select “oF” by pressing the s\tbuttons and push the

PTT key, or press the MENU button to move to the next feature

setting.

SILENT OPERATION

Your radio has a SILENT OPERATION mode. In this mode, all

“beeps” and “tones” are disabled.

To turn the SILENT OPERATION mode on, press the MENU button

until the display shows a “bP” icon while on the right of the “bP”

display, an “on” icon appears. Select “oF” by pressing the s\t

buttons and push the PTT key or the MENU button.

To turn the SILENT OPERATION mode off, press the MENU button

until the display shows a “bP” icon while on the right of the “bP”

display, an “oF” icon appears. Select “on” by pressing the s\t

buttons and push the PTT key or the MENU button.

EXTERNAL SPEAKER/MICROPHONE JACK

Your radio can be used with an optional external

speaker/microphone or headset, freeing your hands

for other tasks. To use an optional speaker/

microphone or headset:

l Insert the plug(s) into the SPK/MIC jacks.

lPlace the earbud into your ear, and adjust the

mic into your desired position.

Note : You can charge a rechargeable NiMH

battery pack thru the CHG Jack

PROBLEM SOLUTION

No Power - Check battery installation and/or replace batteries

Cannot Receive

Messages - Confirm the radios have the same channel

settings.

- Make sure that you are within range of the other

transceivers.

- Buildings and other structures may interfere with

your communication.

Radio is not responding

to button presses - Make sure key lock is not on (See Keypad Lock).

- Radio might need to be reset. Turn radio off then

on.

Display is dim - Recharge or replace batteries.

Charger not functioning - Contacts on the bottom of the radio may require

cleaning.

- Ensure the outlet where the charger is plugged

in is functioning properly.

- Check that the battery pack is installed in the radio

properly.

USE AND CARE

1. Use a soft damp cloth to clean the radio

2. Do not use alcohol or cleaning solutions to clean the radio.

3. Do not immerse the radio in water.

4. Dry the radio with a dry lint-free cloth should it get wet.

5. Turn off the radio and remove the batteries during long-term

storage.

If you have a problem which you believe requires

service, please call first and speak with a service

technician at 816-241-8500. Many problems can be

remedied over the phone without returning the unit for

service.

TROUBLESHOOTING GUIDE SPECIFICATIONS

Channels 22 GMRS/FRS Channels

Operating Frequency UHF 462.5500 ~ 467.7125 MHz

Power Source 4 AAAAlkaline or 4.8V Rechargeable NiMH

battery pack

GMRS/FRS FREQUENCY CHART (MHz)

CH. No CH. Freq. CH. No CH. Freq. CH. No CH. Freq.

1 462.5625 9 467.5875 17 462.6000

2 462.5875 10 467.6125 18 462.6250

3 462.6125 11 467.6375 19 462.6500

4 462.6375 12 467.6625 20 462.6750

5 462.6625 13 467.6875 21 462.7000

6 462.6875 14 467.7125 22 462.7250

7 462.7125 15 462.5500

8 467.5625 16 462.5750

* Channels 8~14 are low-power FRS license free channels

Check out these and other great products at

midlandusa.com

CB Radios

Emergency Crank Radios

Marine Radios

HD Wearable Video Cameras

Bluetooth Headsets

Weather Radios

2-Way Radios

LIMITED WARRANTY

Midland Radio Corporation will repair or replace, at its option without

charge, any Midland FRS/GMRS transceiver which fails due to a

defect in material or workmanship within three years following the

initial consumer purchase.

This warranty does not apply to water damage, battery leak or abuse.

Accessories have a 90 day warranty from date of purchase, including

any antennas, chargers, or earphones.

This warranty does not include the cost of labor for removal or

re-installation of the product in a vehicle or other mounting.

For Product Purchased in the USA:

Performance of any obligation under this warranty may be obtained

by returning the defective product, prepaid freight, along with proof of

purchase to:

Midland Radio Corporation

Warranty Service Department

5900 Parretta Drive

Kansas City, MO 64120

This warranty gives you specific legal rights, and you may also have

other rights, which vary from state to state.

Note: The above warranty applies only to merchandise purchased in

the United States of America or any of the territories or possessions

thereof, or from a U.S. Military exchange.

For Product Purchased in Canada:

Performance of any obligation under this warranty may be obtained

by returning the warranted product, along with proof of purchase, to

your dealer in Canada.

This warranty gives you specified legal rights. Additional warranty

rights may be provided by law in some areas.

AVP-11AVP-HH4

AVP-HH1 AVP-HH5

AVP-HH2 AVP-HH7

AVP-HH3 AVP-HH8

- 1 Open Face

Helmet

Microphone Kit

- $49.99

- 1 Closed Face

Helmet

Microphone Kit

- $49.99

- 2 Over the Ear

Mic. Headsets

w/ PTT

- $19.99

ACCESSORIES

Accessories can be purchased at midlandusa.com or by filling in the

form on the following page and mailing it to the address on the form.

- 2 Surveillance

Headsets

- $39.99

- 2 Behind the

Head Headsets

- $39.99

- 2 Ear Wrap

Headsets

- $39.99

- 2 Mossy Oak

Around the Ear

Headsets with

Boom Mic

- $39.99

- 1 Action Throat

Mic with

Acoustic Ear

Tube

- $39.99

Please send Money Order or fill in Visa/MasterCard information and

mail to the address below. Please DO NOT send cash or checks.

Make Money Order payable to Midland Radio Corporation.

Name: _____________________________________________________

Address: ___________________________________________________

City: _____________________ State: _____Zip Code: ____________

Tel: ______________________ Email: ___________________________

CC#: ____________________ Type: __________ Exp.: ____________

ACCESSORIES ORDER FORM

Mail To:

Midland Radio Corporation

Consumer Dept.

5900 Parretta Drive

Kansas City, MO 64120

----------------

Or Call 816.241.8500.

----------------

To order online go to

midlandusa.com

Sub-Total ___________

Tax (MO, FL, WA only) ___________

S & H _____ $14.95

(Applies to Domestic U.S. only.

For Hawaii, Alaska, and Puerto

Rico S&H will be $36.25 for 1lb

and $64.25 for 2lbs or more).

Total $___________

Qty Item Price Total

AVP-1 $19.99

AVP-H1 $49.99

AVP-H2 $49.99

AVP-H3 $39.99

AVP-H4 $39.99

AVP-H5 $39.99

AVP-H7 $39.99

AVP-H8 $39.99

AVP-6 $39.99

TH1 $39.99

TH2 $99.99

TH3 $29.99

TH4 $109.99

TH1 TH2

TH3 TH4

AVP-66

- Earphone Mic

with Boom

- $39.99

- Earphone Mic

with PTT

- $29.99

- Tactical Action

Boom Mic with

Tactical PTT

- $99.99

- Action Throat

Mic with

Tactical PTT

and Pneumatic

Earphone

- $109.99

- 1 Dual Desk

Charger

- 2 Rechargeable

Battery Packs

- 1 AC Adapter

- 1 DC Cigarette

Lighter Adapter

- $39.99

TACTICAL

HEADSETS

IMPORTANT: This device complies with Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1) this device

may not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

IMPORTANT: Le présent appareil est conforme aux CNR d'Industrie Canada

applicables aux appareils radio exempts de licence. L'exploitation est autorisée

aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi même

si le brouillage est susceptible d'en compromettre le fonctionnement.