Midwest Menards 198-6257 User manual

CRESTONE STRAIGHT
FIRE PIT
www.midwestmanufacturing.com
SKU: 198-6257
Approximate Weight: 2200 lbs.
Approximate Size: 4’ 8” Exterior Dimension x 3’ Interior Dimension x 1’ 4” H

PRODUCT:
Crestone Straight
Small Belgian Wall Block
Medium Belgian Wall Block
Classic Patio Block
DESCRIPTION
Color of Choice
Color of Choice
Color of Choice
Color of Choice
QUANTITY
56
40
8
12
3
2
CONCRETE BLOCKS
ADDITIONAL MATERIALS
PRODUCT:
Pea Gravel
Landscape Adhesive
36” Steel Square Fire Ring
DESCRIPTION
.5 cu. ft.
10 oz Tube
36” x 36”
QUANTITY
5
5
1
SKU#
189 -1124
520-2025
259-5045
PREPARE
Crestone StraightMedium Belgian Wall Block
Small Belgian Wall BlockClassic Patio Block
CRESTONE BLOCK MATERIALS
BELGIAN BLOCK MATERIALS
179-3614
179-3612
179-3610
Straight
Sienna
Tan
Autumn Blend
Color
179-3734
179-3731
179-3732
179-3733
Small
179-3724
179-3721
179-3722
179-3723
Medium
Sienna
Quarry Gray
Tan
Color
179-1101
179-1127
179-1103
SKU
Red
Gray
Tan
Color
CLASSIC PATIO BLOCK
Autumn Blend

A solid foundation is necessary to prevent settling and tilting of each project. We recommend using a
leveling pad, unless local building code requires you to pour a concrete foundation or build another type
of foundation.
FOUNDATION:
• Choose the location for the completed project; place and mark the position of the base layer of blocks.
Once marked, remove the blocks and the organic top soil within the marked area.
• If applicable to your area, create a leveling pad with a non-frost susceptible, well graded, compacted
angular gravel-sand mixture with nes (GW as per ASTM D248). The leveling pad should be a minimum
of 4 to 6 inches thick. For leveling pads greater than 8” thick, the ll material shall be placed in more
than one lift. Each layer or lift of ll material shall be leveled and compacted to a 95% Standard Proctor
density before moving on.
• Once the top layer of ll material is compacted and level, place the base layer of blocks. The base layer
should sit 1 to 2 inches below grade to help further prevent shifting. Use additional ll material to level
the base layer as needed.
* If a concrete slab is required, prepare a leveling pad using the procedures listed in the paragraphs above. The concrete
shall have a minimum compressive strength of 2500 psi. A 4-inch thick concrete slab should be more than sufcient.
A thickened edge and reinforcement of the leveling slabs may be required. Please consult a professional engineer for
specic requirements.
TIPS FOR BUILDING LEVELING PADS:
3
PREPARE
These plans will walk you through each step as you Prepare, Assemble and Enjoy the new addition to your
yard. Check out the Progress Bar at the bottom of each page to track your advancements as you complete
each phase of your project!
INSTRUCTIONS:
• Please research and follow
local building codes prior to
the excavation, construction
and assembly of your
project.
• Exercise caution when
you work with Concrete
Block designs. Wear
protective safety
equipment such as safety
glasses, dust masks,
gloves and a hard hat.
• Whether you plan to
build the project yourself
or to hire a professional,
every project requires a
call to mark your utility
lines.
BEFORE YOU BEGIN:
It is the responsibility of the owner to ensure compliance with all applicable laws, codes and regulations
for any project. Proper safety precautions must be taken prior to and during the construction of each
project. Please follow standard safety guidelines and wear necessary protective equipment when building
and using your new backyard addition.
RESPONSIBILITIES:
Rubber Mallet
Level
Utility Knife
Caulk Gun
Protective Equipment
Tape Measure
TOOL CHECK LIST
Chisel
Standard Hammer

PREPARE:
CRESTONE STRAIGHT FIRE PIT DIMENSIONS
TABLE OF CONTENTS
Level 1 - Level 3
Materials List
Tool Check List
Foundation Guidelines
ASSEMBLE:
Finished Elevations
ENJOY:
Use and Care Instructions
More Concrete Block Ideas
2
3
3
5
6
7
8
9
4
PREPARE
TECHNIQUES
Fasten each layer of block together with
1/4” - 3/8” bead of landscape adhesive on
all bottom block faces unless otherwise
noted. Refer to the landscape adhesive’s
application instructions for proper use.
Follow suggestions on page 3 to build a proper foundation before starting your new project. If not
already set, place the rst level of block 1”- 2” below grade, level and ll in any gaps. Use Level 1
as a reference to place the blocks for all remaining levels.
Refer to the illustrations on the following pages to guide you through each step. Prior to adhering
each level to the previously laid block, place the entire level of blocks and check to make sure the
re pit insert ts properly. Remove small sections at a time to place the adhesive.
Once all levels are complete, position the insert into the nished pit. Fill the base of the pit, up to
and slightly above the bottom of the metal insert, with gravel. Wait a minimum of two days before
starting a re.
INSTALLATION INSTRUCTIONS
* Do not over apply adhesive. It may reduce effectiveness.
Use mineral spirits to remove any unwanted adhesive.
1’ 4”
Level 4 - Level 6
4’ 8”
36” Ring

Level 1 Level 3
(16) Crestone Straight
ASSEMBLE
5
ASSEMBLE
Level 2
(12) Crestone Straight
Important: You will need to remove the back lips from all Crestone
blocks prior to assembly.
Test t the 36” Steel Fire Ring
at this level.
(8) Small Belgian Wall Block
(12) Small Belgian Wall Block
See Corner
Detail
Trim blocks to form corners.
See Corner Detail on Level 1.
(16) Crestone Straight
(12) Small Belgian Wall Block
(4) Medium Belgian Wall Block
Cut Medium Belgians
to 6-1/4”
Corner Detail
11-1/ 2” 11-1/ 2”
Short edges 2-3/4”

6
ASSEMBLE
Allow re pit to fully dry before lling with gravel and starting a re.
Level 4
(12) Crestone Straight
Level 5
Important: You will need to remove the back lips from all Crestone
blocks prior to assembly.
(12) Classic Patio Block
(8) Small Belgian Wall Block
Level 6
(1) Fire Ring
Cut Medium Belgians
to 6-1/4”
(4) Medium Belgian Wall Block

ENJOY
FIRE PIT ELEVATIONS
Side View
7
Top View

With proper use and maintenance you can enjoy this new addition to your
landscape for years to come.
Fire Pit Use:
• When using your re pit, always following burning regulations in your area and never
leave a re unattended.
• Keep the re within the metal insert; any exposure of the ames directly to the concrete
blocks may cause blackening or cracking of the blocks.
• Keep gravel or sand up to and above the base of the metal insert to protect the blocks
from direct ame exposure. The gravel base provides drainage and helps protect any
blocks that are positioned below the bottom of the metal insert.
ENJOY
Use and Maintenance
8
Fire Pit Maintenance:
• Clean your re pit often.
• Wait until the re has burned out completely and all ashes have cooled before
cleaning the re pit.
• Begin by removing the larger pieces of debris; the remaining ash can be scooped
out and/or lightly sprayed with a hose to rinse through the gravel.

NORTHERN LIGHTS
COLLECTION
Cantwell Fireplace 198-1712
Kodiak Firepit 198-1714
Sitka Bench 198-1751
Fjord Fountain 198-1755
PRAIRIE COLLECTION
Hearthstone Fireplace 198-1763
Plateau Bar 198-1765
Echelon Planter 198-1764
Courting Bench 198-1766
CLEARWATER COLLECTION
Alpine Fireplace 198-1701, 1703, 1705
Nordic Bar 198-1736
Cascade Fountain
with Brighton Pillars 198-1761
LAKESHORE COLLECTION
Stockton Firepit 198-1127
Seawall Bench 198-1126, 1128
Starboard Column 198-1129
Saxon Waterwall 198-1131
Poseidon’s Point 198-1130
Portside Pillar 198-1120
STAIR COLLECTION
Four Stair Set 198-1804
Three Stair Set 198-1803
Two Stair Set 198-1802
www.midwestmanufacturing.com
OUTDOOR LIVING KITS
Check out these Outdoor Living Kits and
many more ways to create your own
landscaped paradise by visiting: