Miele CVA 2662 User manual

Quick Guide
Cappuccinatore
To prevent accidents
and machine damage
read the instructions
provided with the machine. M.-Nr. 07 382 380
en - US, CA

Before using the cappuccinatore for
the first time, wash it either in the
dishwasher or with hot water and
liquid dish soap.
Cold milk is best for creating froth.
Pre-warm the cups, before
preparing a drink. Place a cup
under the steam valve and press the
lever down until steam is dispensed.
Use caution. Steam is very hot.
aValve
bCappuccinatore spout
Valve
The steam is regulated by turning the
valve:
1Hot milk is prepared
2Froth is prepared
Do not set the valve between these
two positions: The milk will splatter!
Milk spout
Pushed in: Milk is frothed into the cup
Pulled out: Milk is frothed into the
cappuccinatore
Replace the nozzle on the steam
valve
If your machine uses the steam valve
nozzle shown in the illustration, replace
it with the new nozzle supplied with the
cappuccinatore.
^Use the tool to remove the perforator,
so the nozzle can be replaced.
^Open the appliance door. Press the
steam lever down, screw off the
nozzle and screw on the new one.
^Return the steam lever to the "up"
position.
Cappuccinatore
2

Frothing milk into a cup
^Push the cappuccinatore spout all
the way into the lid.
^Turn the valve all the way to the right
for frothing.
^Fill the cappuccinatore ato the
upper "max" mark with cold milk and
cover with the lid.
^Place the cappuccinatore under the
steam valve and a cup under the
spout b.
^Slowly press the steam lever down.
The steam lever must click into the
down position - otherwise the valve is
not properly connected to the
cappuccinatore.
^Push the steam lever up when
enough froth is prepared.
The steam supply is temporary. If
the steam stops and there is not
enough froth prepared, push the
steam lever up then down again.
Frothing milk into the
cappuccinatore
^Fill the pitcher to the lower "max"
mark with cold milk and cover with
the lid.
^Pull the milk spout out from the lid.
^Turn the valve all the way to the right
for frothing.
^Place the cappuccinatore under the
steam valve.
^Slowly press the steam lever down
a.
The steam lever must click into the
down position - otherwise the valve is
not properly connected to the
cappuccinatore b.
^Push the steam lever up when
enough froth is prepared.
Cappuccinatore
3

Heating milk in the cappuccinatore
^Fill the cappuccinatore to the upper
"Max" mark with cold milk, place the
lid on, pull the spout out from the lid.
^Turn the valve all the way to the left
for heating.
^Place the cappuccinatore under the
steam valve.
^Slowly press the steam lever down
and carefully "connect" the valve to
the cappuccinatore.
Quick cleaning
For a quick cleaning between froths the
cappuccinatore lid can be rinsed with
the steam valve.
The rinsing does not replace the
cleaning of the cappuccinatore in a
dishwasher.
^Select "Maintenance G" using < or
>.
^Select "Rinse Cappuccinatore" and
confirm with OK button.
^Push the cappuccinatore spout into
the "in" position and place an empty
cup underneath the cappuccinatore
spout.
^Press the steam lever down.
The process will stop automatically
when the lid is rinsed.
Complete Cleaning
Thorough cleaning is very important to
prevent the cappuccinatore spout from
becoming blocked and producing little
or no froth. For best results, use a
dishwasher - all parts are
dishwasher-safe.
^Separate the lid, remove all parts and
clean.
^Re-assemble the lid as shown in the
illustration. For the valve to work
properly, the dot on the valve must
face the upper right.
Be sure that the parts are assembled
properly.
Cappuccinatore
4

5

6

7

Alteration rights reserved / 4708
For the most updated manual see the Miele web site.
M.-Nr. 07 382 380 / 01