Miele CVA 5060 User manual

Quick start guide
CVA 50xx
These short instructions are not a substitute
for the Operating instruction booklet supplied
with your coffee machine.
Please read the Operating instruction booklet supplied
with your machine before using it for the first time and
take note of the Warning and Safety instructions as well
as the full descriptions on how to use your machine. M.-Nr. 07 479 630
en - GB, AU, NZ

aMaster switch
bGround coffee chute cover
cGround coffee chute
dSlide control to select fineness of ground coffee
eCoffee bean container
fDrip tray with grid for easier carrying
gWater container (with mains water inlet device on the CVA 5065 only)
hBrew unit
iWaste container
jCentral spout connector (connecting the brew unit and the central coffee spout)
kStainless steel milk flask
Accessory: 1 large cleaning container, 1 small cleaning container, 1 additional lid
for stainless steel milk flask

Using the coffee machine - first steps
Controls
sOn/Off sensor for switching the coffee machine on and off
< Left arrow, for scrolling through the various programme options
OK Sensor for confirming the selection of a programme option and
for saving a setting
> Right arrow, for scrolling through the various programme options
-Sensor for hot water
Display
Drinks selection: coffee, J= hot milk, L= milk froth
User profile: nfor up to 9 different users
Maintenance programmes: G= Milk pipework, Brew unit, Descale, Rinse
Settings: C= For customising your machine
Fill the water container
Filling the coffee bean container
Making a drink
^Fill the water container with fresh, cold
tap water up to the "Max." marker.
^Pull the coffee
bean container
out.
^Slide the lid back and fill the container
with roasted coffee beans.
^Close the lid again.
^Place a cup or glass under the
spouts, and select the drink of your
choice.
^Touch the OK
sensor.

Notes on operation
Double portion
^When using coffee beans, a double portion of coffee or espresso can be se-
lected. To do this, touch the OK sensor again whilst "2 portions?" is in the dis-
play.
To interrupt the drink-making process
^Touch the OK sensor whilst "Stop" is in the display.
Drinks with milk
Making coffee with ready-ground coffee
Programming the amount: setting the portion size for espresso, coffee, hot
milk, milk froth and hot water
^Fill the stainless
steel milk flask to
2-3 cm below the
rim of the flask
with cold milk.
^Open the door,
and place the
milk flask inside
the door.
^Close the lid,
making sure it fits
properly.
^Place a cup of
the required size
under the outlet
spouts, and se-
lect the drink of
your choice.
^Hold the OK sen-
sor until "Prog.
the amount" ap-
pears in the dis-
play.
^Touch the OK
sensor again
once the cup is
filled to the level
you want and
whilst "Save"
appears in the
display.
^Programme Hot
water via the hot
water outlet and
the hot water
sensor (instead
of the OK sen-
sor).
^Pull the cover to
the ground
coffee chute out.
^Open the lid to the ground coffee
chute a.
^Place 1 level spoon of ground coffee
in the chute band then close it.
^Follow the instructions in the display.

Programming the amount: setting the portion size for cappuccino and latte
macchiato
Selecting or creating a User profile
^Place a cup or
glass of the re-
quired size under
the outlet spouts,
and select the
drink of your
choice.
^Use the arrow
sensors to select
the option for the
quantity you
require.
^Confirm by
touching the OK
sensor.
^Use the arrow
sensor to select
"start", and touch
the OK sensor.
^Touch the OK
sensor again
once the cup is
filled to the level
you want and
whilst "Save"
appears in the
display.
^Use one of the
arrow sensors to
select User
profile nand
touch the OK
sensor.
^Selecting an
existing user
profile: Select
the profile you
want, and touch
the OK sensor.
^Creating a new
user profile:
Select "Create"
and touch the
OK sensor.
^Use one of the
arrow sensors to
select the letters
you want and
touch the OK
sensor when
appropriate.
Made a mistake?
Select the bin
symbol and touch
the OK sensor; the
last letter will be
deleted.
Save?
Select OK and
touch the OK
sensor.
Do not save?
Select "Back" and
touch the OK
sensor.
^Touch and keep
your finger on the
OK sensor until
the options for
the drinks
selection appear
in the display.

Important care tips
All parts except for the brew unit, the coffee bean container, the stainless steel
milk flask and lid, and the cover to the central spout are dishwasher safe.
Before use:
^It is very important to programme the water hardness level into the machine to
prevent limescale building up too quickly. See "Settings: Water hardness" in the
Operating instruction booklet.
Regular maintenance:
^Follow all maintenance instructions that appear in the display.
The following must also be cleaned on a regular basis:
Rinse the milk pipework after every use
^Clean the recess
underneath the
water container.
^The connecting piece in the door be-
tween the brew unit and the coffee
outlet should be wiped clean with a
damp cloth. Lubricate the cap once
a month with the silicone grease
supplied.
^Wash the bean
container by
hand with hot
water and wash-
ing-up liquid.
^Follow the clean-
ing instructions
for the machine
door in the Oper-
ating instruc-
tions.
^The drip tray
should be
cleaned in the
dishwasher.
^Using a damp
cloth wipe away
any dry coffee
grounds from in-
side the ma-
chine. A vacuum
cleaner can be
used on dried
coffee grounds.
^Wipe the small
drip tray inside
the door.
^Select "Mainte-
nance" G, and
touch the OK
sensor.
^Select "Rinse
milk pipework"
and touch the
OK sensor.
^Follow the
instructions in the
display.
^Select "Start" and
touch the OK
sensor.

Clean the milk pipework at the end of the day
Discard any remaining milk, wash the milk flask and clean the central spout
^Pull the central
spout right down
a, and remove
the cover b.
^Turn the cover
round, slide the
insert upwards
to remove, and
clean both parts
thoroughly.
^Wash the stain-
less steel flask
with hot water
taking particular
care to clean the
neck and seal
thoroughly.
Soiling can
cause the
machine to
malfunction.
^Wash the handle
of the flask under
running water,
and use a damp
cloth to wipe
away any milk
residues.
^Select "Mainte-
nance" G, and
touch the OK
sensor.
^Select "Clean
milk pipework"
and touch the
OK sensor.
^Follow the
instructions in the
display.
^Select "Start" and
touch the OK
sensor.
^Pull out both
rubber stoppers
and clean them
thoroughly
together with the
jets.
^Replace the
stoppers.
^After cleaning,
push the jets
firmly back up
into place,
ensuring they are
secure.
^Slide the insert
back into the lid
until it clicks into
place.
^Remove the jets
from the central
spout.
^Replace the lid
and slide the
central spout
upwards.

Clean the brew unit
Display message "Please start the cleaning programme" (= degrease the
brew unit)
Descaling the machine (approx. 20-30 mins)
Important: Only use the descaling tablets supplied, and always place the mainte-
nance containers in position to prevent any descaling agent from splashing onto
the front of the machine and damaging it.
The CVA 5065 (plumbed-in model) switches automatically from the mains water
supply to operating with the water container for the descaling programme.
00 / 4208
^Press button a
under the handle
and turn the han-
dle to the left b.
^Press brew unit
catch cdown-
wards and pull
the brew unit out.
^Go to "Maintenance" G... "Clean
brew unit" and select "Start" to run the
cleaning programme.
^Place a cleaning tablet in the chute -
close the lid and follow the
instructions in the display.
^Pull the cover to
the ground
coffee chute off.
^Go to "Mainte-
nance" G...
"Descale" and
select "Start" to
run the descaling
programme.
^Follow the
instructions in
the display.