Miele PT 7186 EL User manual

18.15 10 183 440 / 00
Installation Plan
Tumble dryer
PT 7186 EL (Electrically Heated)
en - US

10 183 440 / 00 2
It is essential to read the operating and installation instructions before
installing, commissioning or using the machine.
This avoids the risk of accidents or damage.
All rights reserved
U.S.A.
Miele, Inc.
National Headquarters
9 Independence Way
Princeton, NJ 08540
Phone:
Fax:
www.mieleusa.com
Technical Service & Support
Nationwide
Phone: [phone]
Fax: [phone]
[email protected]
800-991-9380
609-419-4241

27 9/16
3/4
3/4 27 1/4
17 5/16
28 3/8 20 7/8
1 3/427 3/16
30 1/16
13 3/4
12
12 40 3/16
40 3/16
52 3/16
12
12 12 21 1/4
43 5/16
27 9/16
27 1/4
3/4 3/4
40 3/16
17 5/16
13 3/4
30 1/16
27 3/16
28 3/8
43 5/16
27 1/4
27 3/16
PT 7186 EL - measurements in inches
3

23 5/16 3 15/16
51 3/16
12
12 3 5/8
5 13/16
51 3/16
12
3 5/8
51 3/16
3 5/8
23 5/16 3 15/16
51 3/16
3 5/8
5 13/16
PT 7186 EL - measurements in inches
4

Option: Installation on Miele base (UG/UO) Option: Installation on Miele base (US)
40 3/16
13/16
12
39 3/812 5/8
13/16
27 1/4
27 1/4 26 7/8
43 1/4
17 3/8
24 3/4
24 5/8
12 1/4
27 1/8 27
2 13/16 21 5/8 2 13/16
3 15/16 22 1/16 17 5/16
43 5/16
27
10 13/16
2 1/2
2
1/4
1/2
1 5/8
PT 7186 EL - measurements in inches
5

Option: Installation on concrete platform (BS) Standard installation
11 3/4 40 1/8
3/4
40 1/8
3/4
27 1/2 27 1/4
27 1/8
43 1/4
2 3/4 21 5/8 2 3/4
439 3/8
10 7/8
3
3
10 7/8
21 5/8
27 1/2
43 1/4
17 3/8
22
4
1 5/8 1 5/8
2
1/4
2
1/4
PT 7186 EL - measurements in inches
6

PT 7186 EL - measurements in millimeters
7

PT 7186 EL - measurements in millimeters
8

Option: Installation on Miele base (UG/UO) Option: Installation on Miele base (US)
PT 7186 EL - measurements in millimeters
9

Option: Installation on concrete platform (BS)Standard installation
PT 7186 EL - measurements in millimeters
10

Technical datasheet
Tumble dryer:
Heating:
PT 7186
Electric (EL)
Legend: Abbreviations in bold type:
Connection required en - US
Abbreviations in circle with dashes:
Connection optional or required depending on model version
Optional extras:
UM Miele base
UO 6008 (UO = open base )
Height
12''
305 mm
Width
26 15/16''
684 mm
Depth
27 1/16''
687 mm
UG 6008 (UG = closed base)
Height
12''
305 mm
Width
27 1/4''
692 mm
Depth
27 1/16''
688 mm
12 5/8''
320 mm
27 1/4''
692 mm
US 6008 (US =base with drawer)
Height
Width
Depth 27''
685 mm
BS Concrete base Quality and density of concrete must comply with load.
Concrete base must be firmly secured to floor!
Recommended height
12''
300 mm
Minimum height
2 3/4''
70 mm
Recommended width
≥27 1/2''
≥700 mm
Recommended depth
≥27 1/2''
≥700 mm
Machine connections:
Electrical
connection 1.
2.
Technical datasheet: PT 7186 EL (Electrically Heated)
Date: 2015-04-29 Page: 11
Standard voltage (2 AC 208V 60Hz)V 2AC 208V
Hz 60
kW 4.84
A 2 x 30
78 3/4'' 2000 mm
Voltage
Frequency
Rated load
Fuse rating
Length of supply lead
Supplied with plug NEMA L6-30P NEMA L6-30P
Standard voltage (2 AC 240V 60Hz)
V 2AC 240V
Hz 60
kW 5.7
A 2 x 30
78 3/4'' 2000 mm
Voltage
Frequency
Rated load
Fuse rating
Length of supply lead
Supplied with plug NEMA L6-30P NEMA L6-30P

Electrical connection must comply with national regulations.
Connection using multi-pole lockable wall socket in
compliance with IEC/EN 60309 and IEC/EN 60947 is
recommended in order to simplify electrical tests. If machines
are hard-wired, a multi-pole mains switch must be provided
on site. Switches with a contact gap of more than 3 mm can
be used. These include switches, fuses and contactors
(IEC/EN 60947). A wall socket or mains isolator must be
easily accessible after installation.
Reinstallation of the supply point, changes to the equipment
or checks on the protective conductor, including determination
of correct fuse rating, should only be performed by a properly
trained electrician.
If necessary, equipotential bonding with good galvanic contact
must be provided in accordance with all appropriate national
and local regulations.
Vented
Nominal air throughput in vented mode
188 cfm
320 m³/h
Max. permissible pressure loss
0.06 psi
420 Pa
Waste air/gas temperature, max.
176°F
80°C
Connector on machine (int. diameter)
3 15/16''
100 mm
Connection pipe provided on site (ext. diameter)
3 15/16''
100 mm
Miele adapter, Mat. no. 6595070 (int. diameter 100 mm) for
flexible aluminum ducting and adapter, Mat. no. 915051, (ext.
diameter 110 mm) for connection to standard heat-resistant
plastic pipes supplied.
As relative humidity inside the vent ducting can be as high as
100%, suitable measures must be taken to prevent a
backflow of condensate into the machine.
Air intake
Standard connection:
=> Air intake from installation site
Min. air intake cross-section
(to prevent draughts in room)
37 in2 237 cm2
A sufficient supply of fresh air should be ensured to replace
the air extracted.
Fittings for base
/ floor
installation
5/16'' x 2 9/16'' 8 mm x 65 mm
1/2'' x 2 3/8'' 12 mm x 60 mm
Miele base UG/UO 6008
4 × metal angled brackets
(to secure machine to base)
4 × screws DIN 571 (Ø × length)
4 × rawl plugs (Ø × length)
Base must be bolted to the floor. Machine must be fixed to the
base. Fixing materials for a floating screed floor are to be
provided on site.
1/4'' x 2'' 6 mm x 50 mm
5/16'' x 1 9/16'' 8 mm x 40 mm
Miele US6008 base
4 x metal angled brackets
(to secure machine to base)
4 × screws DIN 571 (Ø × length)
4 × rawl plugs (Ø × length)
Base must be bolted to the floor. Machine must be fixed to the
base. Fixing materials for a floating screed floor are to be
provided on site.
1/4'' x 2'' 6 mm x 50 mm
5/16'' x 1 9/16'' 8 mm x 40 mm
Installation onfloor orconcrete base
2 × clamps
2 × screws DIN 571 (Ø × length)
2 × rawl plugs (Ø × length)
Machine must be fixed to the base or floor. Fittings are
supplied with machine. Fixing materials for a floating screed
floor are to be provided on site.
Technical datasheet: PT 7186 EL (Electrically Heated)
Date: 2015-04-29 Page: 12

Machine data
Unit width
27 9/16''
700 mm
30 1/16''
763 mm
40 3/16''
1020 mm
27 1/4''
692 mm
Unit depth
Unit height
Casing width
Casing depth 27 3/16''
690 mm
Minimum width of delivery access to installation site
28 3/8''
720 mm
Recommended rear wall gap (measured to front of machine) 43 5/16''
1100 mm
Minimum rear wall gap (to front of machine)
Recommended rear wall gap ensures sufficient space for
maintenance and servicing.
35 7/16''
900 mm
Net weight
170 lbs
77 kg
Dynamic floor load, max.
1000 N
Average heat dissipation
(dependent on ambient room temperature and program
selected)
1535 BTU/hr 0.45 kWh
Sound pressure (re 20 mPA), workplace-related
(at distance of 1 m and height of 1.6 m)
<70 dB (A)
Installation should only be carried out by authorized installers in accordance with valid regulations! Observe installation
instructions when installing machine! All rights reserved!
Technical datasheet: PT 7186 EL (Electrically Heated)
Date: 2015-04-29 Page: 13