Miele PT 8803 EL User manual

02.11 Mat. NR. 07 803 900 / 02
Installation plan
Tumble dryers
.
Installatieschema
Droogautomaat
PT 8803 EL
PT 8805 EL
PT 8807 EL
nl - NL
en - GB

Mat. NR. 07 803 900 / 02
2
Lees beslist de gebruiks- en montagehandleiding voordat u uw
apparaat plaatst, installeert en in gebruik neemt.
Dat is veiliger voor uzelf en u voorkomt schade aan uw apparaat.
Technische wijzigingen voorbehouden
It is essential to read the operating and installation instructions before
installing, commissioning or using the machine.
This avoids the risk of accidents or damage.
All rights reserved

Installationsplan / Installation plan: PT 8803/8805/8807
Datum / Date: 12.01.2011 Seite / Page: 9
Technical datasheet
Tumble dryer:
Heating:
PT 8803/8805/8807
Electric (EL)
Legend:
Abbreviations in bold type:
Connection required
en - GB
Abbreviations in circle with dashes:
Connection optional or required depending on model version
Optional extras:
BS
Concrete plinth
Quality and density of concrete must comply with load.
Concrete plinth must be firmly secured to floor!
Recommended height
mm
100
Minimum height
mm
50
Width min.
mm
1200
Width:min.
mm
1400
Machine connections:
Electrical
connection
1. Standard voltage (as supplied)
V
3N AC 380 - 415
Frequency
Hz
50
Rated load
kW
34.4 –40.7
Fuse rating
A
3 × 63
Connection cable, min. cross-section
mm²
5 × 16
Cable screw connector
M 50
Connection cable (to be ordered separately)
2. Standard voltage (as supplied)
V
3 AC 220 - 240
Frequency
Hz
50
Rated load
kW
34.8 –41.1
Fuse rating
A
3 × 100
Connection cable, min. cross-section
mm²
4 × 25
Cable screw connector
M 50
Connection cable (to be ordered separately)
Non-standard voltages:
OS 440
Standard voltage (as supplied)
V
3 AC 440
Frequency
Hz
60
Rated load
kW
37.9
Fuse rating
A
3 × 63
Connection cable, min. cross-section
mm²
4 × 16
Cable screw connector
M 40
Connection cable (to be ordered separately)
Electrical connection must comply with national regulations.
Connection using multi-pole wall socket in compliance with
IEC/EN 60309 and IEC/EN 60947 is recommended in order to
simplify electrical tests.
If machines are hard-wired, a multi-pole mains switch must be
provided on site.
A wall socket or mains isolator must be accessible after
installation.

Installationsplan / Installation plan: PT 8803/8805/8807
Datum / Date: 12.01.2011 Seite / Page: 10
Equipotential
bonding
Connection with male thread
mm
10 × 35
with washers and nut.
M
10
Accessories not included (except with offshore version).
If necessary, equipotential bonding with good galvanic
contact must be provided in accordance with all appropriate
national and local regulations.
Peak load energy
management
Control contact voltage
V
AC 230
Connection cable, min. cross-section
mm²
5 × 1.5
Connection cable (to be ordered separately)
Connection via a flexible supply lead with a separate isolator
is recommended. The isolator should be visible and easily
accessible after machine installation.
Vented
Max. nominal air flow in vented mode (PT 8807 only)
m³/h
1100
Nominal air flow (PT 8803/8805 only)
m³/h
1000
Max. permissible pressure loss
Pa
300
Connection on machine side (ext. diameter)
mm
150
Connection pipe provided on site (int. diameter)
mm
150
Max. temperature
°C
80
As relative humidity inside the vent ducting can be as high as
100%, suitable measures must be taken to prevent a
backflow of condensate into the machine.
Air intake
Standard connection: Air intake from installation site
Unobstructed air intake into room recommended (corres-
ponding to 3 times the vent cross-section of machine)
cm²
531
A sufficient supply of fresh air should be ensured to
replace the air extracted.
Alternative connection: Ducted air intake (from outside
building)
Connector on machine (int. diameter)
mm
161
Connection pipe provided on site (ext. diameter)
mm
160
Lid removal exposes live components! For safety reasons,
the pipe connected for central air intake should be at least
900 mm long and secured using two screws.
Fittings (supplied)
Without plinth
2 × clamps
2 × screws DIN 571 (Ø × length)
mm
6 × 40
2 × rawl plugs (Ø × length)
mm
10 × 50
The machine should be bolted to the floor.
Fixing materials for a floating screed floor are to be provided
on site.
On concrete platform
2 × clamps
2 × screws DIN 571 (Ø × length)
mm
6 × 40
2 × rawl plugs (Ø × length)
mm
10 × 50
Machine must be bolted to the floor!
Fixing materials for a floating screed floor are to be provided
on site.