Miele VENTED DRYER T 1302 Manual

© 2004 Miele
TECHNICAL INFORMATION
Touchtronic Clothes Dryers
Includes: T1302, T1303, T1322, T1329ci
T1403 & T1405

This page intentionally left blank.

Table of Contents
GENERAL INFORMATION
A. Warning and Safety Instructions 3
B. Modification History 5
C.TechnicalData 7
D. Layout of Electrical Components 9
VentedModels 9
Condenser Models 11
010 – Cabinet and Front Panel
1 Technical Data 13
2 Function 15
3 Fault Repair 15
4Service 15
4.1 Lid – Removal 15
4.2 Plinth (Toekick) – Removal 16
4.3 Front Panel – Removal 16
4.4 Side Panel – Removal 16
4.5 Support Bracket – Removal 17
4.6 Rear Access Panel – Removal 17
020 – Door and Door Lock
1TechnicalData 19
1.1 Door Lock 21
2 Function 21
3 Fault Repair 21
4Service 21
4.1 Outer Door Panel – Removal 21
4.2 Door Lock – Removal 22

030 – Drum, Rear Bearing, Sensor and Heater Bank
1TechnicalData 23
1.1 Heater Bank (NTC) Temperature Sensor – Resistance Values 25
2 Function 26
2.1 Residual Moisture Sensor System 26
2.1.1 Residual Moisture Sensing – Drum Assembly 26
2.1.2 Residual Moisture Sensor – Brush Assembly 26
2.2 Drum Bearing 26
2.3 Heating 27
2.3.1 Heater Bank 27
2.3.2 Heater Bank Temperature Sensor 27
2.3.3 Thermostats (Temperature Limiters) 27
3 Fault Repair 27
4Service 28
4.1 Drum – Removal 28
4.2 Drum Rib – Removal 29
4.3 Slip Ring – Removal 29
4.4 Drum Bearing – Removal 30
4.5 Heater Bank – Removal 31
4.6 NTC Temperature Sensor – Removal 33
4.7 Thermostats (Temperature Limiters) – Removal 34
4.8 Brush Unit (Residual Moisture Sensor) – Removal 34
4.9 Residual Moisture Sensor Carbon Brush – Replacement 35
4.10 Rear Seal – Removal 36

040 – Drive and Fan Motor
1TechnicalData 39
2 Function 39
2.1MainMotor 39
3 Fault Repair 40
4Service 40
4.1 Drum Drive Belt – Removal 40
4.2 V-Belt – Removal 41
4.3 Intermediate Drive – Removal 41
4.4 Fan Impeller 41
4.5 Drive Motor – Removal 41
050 – Air Circulation and Front Bearing
1TechnicalData 45
1.1 Temperature Sensor (Fan Housing) – Resistance Values 45
2 Function 46
2.1 Fill Ring 46
2.2 Front Drum Bearing 46
2.3 NTC Temperature Sensor 46
2.4 Front Seal 46
2.5 Porthole Seal 46
3 Fault Repair 48
3.1 Drying temperature too high 48
4Service 49
4.1 Fill Ring – Removal 49
4.2 Front Drum Bearing - Adjustment 50
4.3 Light Bulb – Replacement 51
055 – Condenser System
1TechnicalData 55
2 Function 55
2.1 Condenser Box – Overview 55
2.2 Float Switch & Condenser Pump 56
2.3 Condenser Drawer 57
3 Fault Repair 58
3.1 Long Drying Time 58
3.2 Water Leaking from appliance 58
4Service 58
4.1 Condenser Box – Cleaning 58

060 – Fascia Panel and Electrical Components
1TechnicalData 62
2 Function 62
2.1 Heater Relays 62
3 Fault Repair 63
3.1 Fault Summary 63
4Service 64
4.1 Programming Mode 64
4.2 Demonstration Mode (Dealer Displays) 66
4.3 Service Mode 67
4.4 Fascia Panel – Removal 72
4.5 Electronic / Controls – Service Position 73

Touchtronic Clothes Dryers - List of Figures
D-1 Layout of Components – Vented Models 9
D-2 Layout of Components – Condenser Models 11
010-1 Cabinet Construction 15
010-2 Support bracket 17
020-1 Removing the outer door panel 21
020-2 Door Lock 22
030-1 Drum Bearing 28
030-2 Drum Rib Hardware 29
030-3 Drum Bearing 30
030-4 Heater Bank Components 31
030-5 Wiring Harness Holder 32
030-6 Access Panel to Heater Bank (Removed) with Heater Bank 33
030-7 Wiring Harness Holder 34
030-8 Residual Moisture Sensor Brush Replacement 35
030-9 Rear Drum Seal 36
040-1 Motor and Fan Impellers (Condenser Model) 39
040-2 Drives 40
050-1 Drum Support Housing (vented) 47
050-2 Drum Support Housing (condenser) 48
050-3 Front Drum Support Bearing 50
050-4 Opening the Light Bulb Cover 51
055-1 Condenser Box Assembly 55
055-2 Float Switch and Drain Pump 56
055-3 Condenser Drawer 57
055-4 Condenser Box Access Panel 59
055-5 Condenser Door Lock 59
055-6 Unlocking the Condenser Box Lock 59
055-7 Removing the Condenser Box 60
055-8 Rinsing the side of the Condenser Box 60
055-9 Rinsing the Condenser Box 60
060-1 Fascia Panel Removal 72
060-2 Electronic Retaining Screw 73
060-3 Button Assembly 74
060-4 Electronic / Controls in service position 74

Touchtronic Clothes Dryers - List of Tables
C-1 Overview of Models 7
C-2 Electrical Information 7
030-1 Heater Bank NTC Temperature Sensor Values 25
030-2 Heater Element Activation 26
050-1 Fill Ring NTC Temperature Sensor Values 45
060-1 Fault Summary 63
060-2 Program Mode Positions 65
060-3 Service Mode (1 of 4) 68
060-4 Service Mode (2 of 4 69
060-5 Service Mode (3 of 4) 70
060-6 Service Mode (4 of 4) 71

Technical Information
1
T1302, T1303, T1322, T1329ci, T1323c,
T1403 and T1405 Clothes Dryers
General Information

Technical Information
2
T1302, T1303, T1322, T1329ci, T1323c,
T1403 and T1405 Clothes Dryers
This page intentionally left blank.

Technical Information
3
T1302, T1303, T1322, T1329ci, T1323c,
T1403 and T1405 Clothes Dryers
A Warning and Safety Instructions
1 General Information
Service of this appliance should only be performed by qualified
personnel; in accordance with local and national codes.
Power should be disconnected from the appliance during service.
Unplug the appliance, or the shut off the appropriate circuit breaker.

Technical Information
4
T1302, T1303, T1322, T1329ci, T1323c,
T1403 and T1405 Clothes Dryers
This page intentionally left blank.

Technical Information
5
T1302, T1303, T1322, T1329ci, T1323c,
T1403 and T1405 Clothes Dryers
B Modification History
04/2004 Miele USA Preliminary Information
06/2004 Miele USA Revised
08/2004 Miele USA Revised

Technical Information
6
T1302, T1303, T1322, T1329ci, T1323c,
T1403 and T1405 Clothes Dryers
This page intentionally left blank.

Technical Information
7
T1302, T1303, T1322, T1329ci, T1323c,
T1403 and T1405 Clothes Dryers
C Technical Data
Overview of Models
Table C-1: Overview of model numbers
Note
All models are left hinged. The door cannot be changed to right
hinge operation.
Electrical Information
Electrical Requirements Electrical Connection
120/240 (208) VAC
(4 wire connection)
60 Hz, 15amp Circuit
NEMA 14-30 Molded Plug
(Do not remove)
Table C-2: Electrical information
Model Number Capacity Additional Information
T1302 5 Kg Angled Controls, Vented
T1303 5 Kg Flat Controls, Vented
T1322C 5 Kg Angled Controls, Condenser
T1329C 5 Kg Fully Integrated Style,
Condenser (match for W1119)
T1323C 5 Kg Flat, Condenser
T1403 6 Kg Angled Controls, Vented
T1405 6 Kg Angled Controls, Vented,
Stainless Steel Finish

Technical Information
8
T1302, T1303, T1322, T1329ci, T1323c,
T1403 and T1405 Clothes Dryers
This page intentionally left blank.

Technical Information
9
T1302, T1303, T1322, T1329ci, T1323c,
T1403 and T1405 Clothes Dryers
D Layout of Electrical Components
Vented Models
Figure D-1: Overview of Components – Vented Models
1. (B3/1) Residual Moisture Sensor (Drum Ribs, Slip Rings)
2. (2R30) NTC Temperature Sensor (Heater Bank)
3. (M5) Main Drive / Fan Motor
4. (2K1/1) Heater Relay
5. (1K1/1) Heater Relay
6. (Z1) Interference Suppression Capacitor
7. (1N1) Electronic Unit
8. (S2) On/Off Switch
9. (H3/6) Drum Light
10.(F1) Temperature Limiters-2 (Non Re-settable)
11.(A2) Door Lock
12.(C5) Capacitor – (for Motor M5)
13.(1R30) NTC Temperature Sensor (Fan Housing)

Technical Information
10
T1302, T1303, T1322, T1329ci, T1323c,
T1403 and T1405 Clothes Dryers
This page intentionally left blank.

Technical Information
11
T1302, T1303, T1322, T1329ci, T1323c,
T1403 and T1405 Clothes Dryers
D Layout of Electrical Components
Condenser Models
A2 Door Lock
B3/1 Residual Moisture Sensor
B8/7 Level Switch
C5 Capacitor
1F1 / 2F2 Temperature Limiter (Non Re-settable)
H3/6 Drum Lighting
K1/1 Heating Relay
M5 Fan And Drum Drive Motor
M13 Condensate Pump (Condenser Dryer Only)
1N1 Electronic
R1 Heater Bank
R2 Heater Bank
1R30 NTC Temperature Sensor (Fan Housing)
2R30 NTC Temperature Sensor (Heater Bank)
S2 On/Off Switch
Z1 Interference Suppression Capacitor
Figure D-2: Overview of Components – Condenser Models
1R30

Technical Information
12
T1302, T1303, T1322, T1329ci, T1323c,
T1403 and T1405 Clothes Dryers
This page intentionally left blank.