mikroElektronika dsPIC Ready3 User manual

MikroElektronika
dsPIC Ready3™
Manual
All Mikroelektronika’s development systems feature a large number of peripheral
modules expanding microcontroller’s range of application and making the
process of program testing easier. In addition to these modules, it is also
possible to use numerous additional modules linked to the development system
through the I/O port connectors. Some of these additional modules can operate
as stand-alone devices without being connected to the microcontroller.
Additional board

MikroElektronika
Figure 1: dsPIC Ready3 additional board
How to connect the board?
The dsPIC Ready3 board features ve 2x5 connectors (CN1 - CN5) that enable connection between the pins of the
microcontroller plugged into the appropriate socket on the board and external devices. A 2x5 connector CN6 is used
to connect the dsPICFlash programmer to the microcontroller pins used for programming. A USB connector CN51
enables connection between the additional board and a PC via the UART module. In order to enable USB-UART
communication, it is necessary to place the appropriate switch on the DIP switch SW1 to the ON position. By doing
this, the RX and TX pins of the USB-UART module are connected to the appropriate pins of the microcontroller. The
additional board is powered with a voltage in a range between 8 and 16V AC/DC via the CN8 connector.
How to use the board?
In order to use the dsPIC Ready3 additional board, it is rst necessary to place a microcontroller in DIP28 package
into one of two appropriate socket supplied on the board. The microcontroller is programmed with the dsPICFlash
programmer that is plugged via its IDC10 connector into a 2x5 connector CN6 supplied on the board. In order to reset
the microcontroller, just press the RESET button. When the programming process is nished, it is necessary to place
jumpers over the 2x5 connector CN6, Figure 1.
dsPIC Ready3
The dsPIC Ready3 additional board is used to experiment with dsPIC® microcontrollers in DIP28 package.
Key features:
- Data transfer via USB-UART communication;
- Programming via the external programmer;
- Pads;
- 8 to 16V AC/DC power supply voltage;

MikroElektronika
Figure 2: Programming the on-board microcontroller

MikroElektronika
MCUTX-
MCURX-
U4
FT232RL
DCD#
CTS#
CBUS4
CBUS2
CBUS3
OSCO
OSCI
TEST
AGND
NC
CBUS0
CBUS1
GND
VCC
RESET#
GND
3V3OUT
USBDM
USBDP
DSR#
TXD
DTR#
RTS#
VCCIO
RXD
RI#
GND
NC
VCC
C12
100nF
VCC
C13
100nF
VCC
C11
100nF
VCC
CN51
USB B
RESET#
USBDP
USBDM
D+
GND
VCC
D-
R3
10K
R2
4K7
Bottom view
VCC
GND
D+
D-
VCC
E3
10uF
RB8
RB0
RE0
RE4
RD0
RB2
RE2
RE8
RF2
RD8
RF2-PGC
RB4
RB6
RF4 RF3-PGD
RC14
RF6 MCLR-MCU
RB1
RE1
RE3
RE5
RD1
RB3
RF3
RD9
RF2
RC13
RB9
RB5
RB7
RF5 RF3
MCLR
VCCVCC
VCC
VCC
VCC
T1
VCC
VCC VCC
PORTB&C
PORTB
PORTE
PORTF
PORTD
CN2CN1
CN4
CN5
CN3
CN6
C10
100nF
VCC
REG1
1
7805
3
2
2
E1
E2
330uF
10uF
D1
4x1N4007
D2
D3 D4
CN8
X1
8MHz
C1
OSC1
OSC2
22pF
C2
22pF
R1
10K
CLRM
RESET
VCC
CN10
CN9
3C
100nF
RF2
RF3
RF4
RF5
RC14
RC13
SW1
RD1 14
RD9 14
VCC 13
VCC 13
RC14 12
RC14 12
RC13 11
RC13 11
OSC2 10
OSC2 10
OSC1 9
OSC1 9
GND 8
GND 8
RB5 7
RB5 7
RB4 6
RB4 6
RB3 5
RB3 5
RB2 4
RB2 4
RB1 3
RB1 3
RB0 2
RB0 2
MCLR-MCU 1
MCLR-MCU 1
15 RD0
15 RD8
16 RE8
16 RF6
17 RF3-PGD
17 RF3-PGD
18 RF2-PGC
18 RF2-PGC
19 GND
19 GND
20 VCC
20 VCC
21 RE5
21 RF5
22 RE4
22 RF4
23 RE3
23 RB9
24 RE2
24 RB8
25 RE1
25 RB7
26 RE0
26 RB6
27 GND
27 GND
28 VCC
28 VCC
DIP28A
DIP28B
PIC30F2010, 3010, 4012
PIC30F2012, 3013
C4
100nF
VCC
C7
100nF
VCC
C5
100nF
VCC
C8
100nF
VCC
C6
100nF
VCC
C9
100nF
VCC
Figure 3: The dsPIC Ready3 board connection schematic

MikroElektronika
Figure 4: Dimensions of the dsPIC Ready3 additional board

MikroElektronika
If you want to learn more about our products, please visit our website at www.mikroe.com If you are experiencing some problems with any of our products or just need additional information, please place your ticket at www.mikroe.com/en/support If you have any questions, comments or business proposals, do not hesitate to contact us at of[email protected]

Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
MikroElektronika:
MIKROE-451