Milestone pro MP-SU21T-KVM User manual

MP-SU21T-KVM
18Gbps HDMI+USB-C KVM Switcher KIT
All Rights Reserved
Version: MP-SU21T-KVM_2022V1.1
User Manual

18Gbps HDMI+USB-C KVM Switcher KIT
Preface
Read this user manual carefully before using the product. Pictures shown in this
manual are for reference only. Different models and specifications are subject to real
product.
This manual is only for operation instruction, please contact the local distributor for
maintenance assistance. The functions described in this version were updated by April,
2022. In the constant effort to improve the product, we reserve the right to make
functions or parameters changes without notice or obligation. Please refer to the
dealers for the latest details.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.

18Gbps HDMI+USB-C KVM Switcher KIT
SAFETY PRECAUTIONS
To ensure the best from the product, please read all instructions carefully before using
the device. Save this manual for further reference.
⚫Unpack the equipment carefully and save the original box and packing material
for possible future shipment.
⚫Follow basic safety precautions to reduce the risk of fire, electrical shock and
injury to persons.
⚫Do not dismantle the housing or modify the module. It may result in electrical
shock or burn.
⚫Using supplies or parts not meeting the products’ specifications may cause
damage, deterioration or malfunction.
⚫Refer all servicing to qualified service personnel.
⚫To prevent fire or shock hazard, do not expose the unit to rain, moisture or install
this product near water.
⚫Do not put any heavy items on the extension cable in case of extrusion.
⚫Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
⚫Install the device in a place with fine ventilation to avoid damage caused by
overheat.
⚫Keep the module away from liquids.
⚫Spillage into the housing may result in fire, electrical shock, or equipment
damage. If an object or liquid falls or spills on to the housing, unplug the module
immediately.
⚫Do not twist or pull by force ends of the cable. It can cause malfunction.
⚫Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power
to the device before cleaning.
⚫Unplug the power cord when left unused for a long period of time
⚫Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

18Gbps HDMI+USB-C KVM Switcher KIT
Table of Contents
1. Product Introduction....................................................................................................1
1.1 Features ............................................................................................................1
1.2 Packing List .......................................................................................................2
1.3 Customer Service ..............................................................................................2
2. Specification ...............................................................................................................3
3. Panel Description........................................................................................................5
3.1 Transmitter.........................................................................................................5
Front Panel..............................................................................................................5
Rear Panel.............................................................................................................6
3.2 Receiver ............................................................................................................6
Front Panel..............................................................................................................7
Rear Panel...............................................................................................................7
4. EDID Management .....................................................................................................8
5. GUI Control.................................................................................................................9
5.1 Video Tab.........................................................................................................10
5.2 Configuration Tab ............................................................................................10
5.2.1 EDID......................................................................................................10
5.2.2 Auto Downscale.....................................................................................11
5.2.3 HDCP ....................................................................................................11
5.2.4 Tags.......................................................................................................12
5.3 CEC Tab ..........................................................................................................12
5.3.1 Input ......................................................................................................13
5.3.2 Output....................................................................................................13
5.3.3 User-defined..........................................................................................14
5.4 RS232 Tab.......................................................................................................14
5.5 Network Tab.....................................................................................................15
5.6 Access Tab ......................................................................................................16
6. RS232 control ...........................................................................................................17
6.1 RS232 control software ...................................................................................17
6.2 RS232 Command ............................................................................................18
6.2.1 System control.......................................................................................18

18Gbps HDMI+USB-C KVM Switcher KIT
6.2.2 Source control .......................................................................................20
7. System Connection...................................................................................................25
8. Panel Drawing ..........................................................................................................27

18Gbps HDMI+USB-C KVM Switcher KIT
1
1. Product Introduction
MP-SU21T-KVM is an 18Gbps switcher kit. It supports up to 4K/60/4:4:4, HDR10 and
Dolby Vision, HDCP 2.2. It also supports uncompressed transmission of 18Gbps
signals with a distance of up to 100m. At the same time, it can be connected to KVM
equipment, which is very suitable for equipment connection and signal transmission in
conference rooms. The switcher kit also supports RS232&CEC control and bidirectional
48V PoC
1.1 Features
⚫HDMI 2.0, highest support 4K@60HZ 4:4:4, HDR10 and Dolby Vision, HDCP 2.2,
⚫1 x HDMI input, 1 x USB-B host, 1 x USB-C input, 1 x HDMI output and 1 x
HDBaseT output
⚫HDBT 3.0, support 100m transmission and bidirectional 48V PoC
⚫Support RS232 control and CEC control
⚫USB-C input support 60W external charging
⚫Auto switch 5V or TMDS detection
⚫Support Dry Contact control

18Gbps HDMI+USB-C KVM Switcher KIT
2
1.2 Packing List
1 x MP-SU21T-KVMT
4 x 3-pin terminal block
1 x 5-pin terminal block
1 x 3-pin to DB9 RS232 cable
2 x hangers
4 x screws
4 x foot pads
1 x MP-SU21T-KVMR
1 x 3-pin terminal block
1 x 5-pin terminal block
2 x hangers
2 x screws
4 x foot pads
1 x DC24V/5A power adapter
1 x English manual
1.3 Customer Service
We provide limited warranty for the product within three years counting from date of
purchase (The purchase invoice shall prevail).
Note: Please contact your distributor immediately if any damage or defect in the
components is found.

18Gbps HDMI+USB-C KVM Switcher KIT
3
2. Specification
Transmitter
Receiver
Video
Video Input
(1) HDMI IN, (1) USB-C IN
(1) HDBT IN
Video Output Connector
(1) Type-A female HDMI
(1) Type-C
(1) RJ45
Input Resolution
HDMI: Up to 4K@60Hz 4:4:4
HDR10, Dolby Vision
USB-C: Up to 4K@60Hz 4:4:4
Up to 4K@60Hz 4:2:0
Video Output
(1) HDMI OUT (1) HDBT OUT
(1) HDMI
Video Output Connector
(2) Type-A female HDMI
(1) Type-A female HDMI
Output Resolution
HDMI: Up to 4K@60Hz 4:4:4
HDR10, Dolby Vision
HDBT: Up to 4K@60Hz 4:2:0
Up to 4K@60Hz 4:4:4 HDR10,
Dolby Vision
HDMI Standard
Up to HDMI 2.0b
Up to HDMI 2.0b
HDCP Version
Up to HDCP 2.2
Up to HDCP 2.2
Audio
HDMI Embedded Audio Format
LPCM 7.1 audio, Dolby Atmos®, Dolby® TrueHD, Dolby Digital®
Plus, DTS:X™, and DTS-HD® Master Audio™ pass-through.
Audio Output Connector
(1) 5-pin terminal block
(1) 5-pin terminal block
Frequency Response
20Hz–20KHz, ±3dB
Max Output Level
0.88 Vrms ±0.5 dB. 2 V = 16 dB headroom above -10 dBV (316
mV) nominal consumer line level signal
SPDIF: ±0.05dBFS
THD+N
< 0.05% (-80 dB), 20 Hz –20 kHz bandwidth, 1 kHz sine at 0
dBFS level (or max level)
SNR
> 80dB, 20Hz-20 kHz bandwidth
SPDIF: > 90dB, 20Hz-20 kHz bandwidth
Crosstalk Isolation
< -80 dB, 10 kHz sine at 0 dBFS level (or max level before clipping)
L-R Level Deviation
< 0.3 dB, 1 kHz sine at 0 dBFS level (or max level before clipping)
Output Load Capability
1k ohm and higher (supports 10x paralleled 10k ohm loads)
Noise Level
>70dB @ 1 kHz
Control

18Gbps HDMI+USB-C KVM Switcher KIT
4
Control port
(1) EDID switch, (2) DEVICES
(1) ETHERNET, (1) FW,
(1) HOST, (2) GR, (2) RS232
(1) TCP/IP
(4) DEVICE, (1) ETHERNET
(1) RS232
Control Connector
(1) 4-pin DIP switch
(2) USB Type-A, (1) RJ45
(1) Micro-USB, (1) USB Type-B
(2) 3-pin terminal block
(2) 3-pin terminal block, (1) RJ45
(3) USB Type-A, (1) USB Type-C
(1) RJ45, (1) 3-pin terminal block
General
Operation Temperature
-5 ~ +55℃
Storage Temperature
-25 ~ +70℃
Relative Humidity
10% ~ 90%
External Power Supply
Input: AC 100~240V, 50/60Hz; Output: 24V DC 5A.
Power Consumption
76.5W (Max)
USB-C Power Charging
60W(Max)
Dimension (W*H*D)
265W x 150D x 32H mm
173W x 95D x 24.5H mm
Net Weight
1020g
410g

18Gbps HDMI+USB-C KVM Switcher KIT
5
3. Panel Description
3.1 Transmitter
Front Panel
No.
Name
Description
①
Power LED
1 x green indicator light, the light is always on when the
machine is working, and it goes out when the power is off
②
SELECT
⚫1 x White non-backlit button, 3 x blue indicator lights,
⚫Click the button to select the input source (HDMI or USB-
C), press and hold for 3 seconds to enter or exit automatic
switching mode, and the corresponding indicator is always
on
③
DISPLAY
⚫1 x white non-backlit button, 2 x blue indicator lights;
⚫Press the button to send the DISPLAY ON/OFF CEC and
RS232 commands to control the TX and RX display
terminal switches at the same time, and the corresponding
indicator light is always on;
④
BLACK
SCREEN
⚫1 x white non-luminous button, 2 x blue indicator lights;
⚫Press the button to enter or exit the output black screen
state, and the corresponding indicator light is always on;
⑤
EDID
1 x 4-pin DIP switch for EDID management
⑥
DEVICES
2 x USB-A 3.0, connect keyboard, mouse, microphone,
printer and other equipment
⑦
ETHERNET
1 x RJ45, used for network passthrough transmission
⑧
FW
1 x Micro-USB, used for MCU firmware upgrade
FW
EDID
ON
OFF 1 0
1 2 3 4
HDMI
USB-C AUTO
1 2
DEVICES
ON OFF
DISPLAY
ON OFF
BLACK SCREEN
SELECT
AUTO/3s
ETHERNET
1 2 3 4 5 6 7 8

18Gbps HDMI+USB-C KVM Switcher KIT
6
Rear Panel
No.
Name
Description
①
USB-C
1 x USB-C 3.0 input, support external 60W charging
②
HOST
1 x USB-B 3.0, connect to HOST devices such as laptops
③
HDMI IN
1 x HDMI input, connect to HOST devices such as laptops
④
HDMI OUT
1 x HDMI loop output
⑤
HDBT
1 x HDBT output, the green light is always on when the
signal is with HDCP, flashes when the input signal is without
HDCP; the yellow light is always on after the TX and RX are
connected;
⑥
AUDIO
1 x 5-pin balanced audio output, output audio de-embedding
⑦
Grommet
GR1: Correspond the USB-C
GR2: Conrrespond the HDMI
SM: Switch to the current source
BO: Print a black screen to all outputs.
⑧
RS232
LOCAL: Connect the control devices to control the
transmitter
PASS: Bidirectional passthrough transmission with Receiver
⑨
Upgrade
1 x Built-in short-handled buttons, press and hold for 3s to
enter the upgrade mode, and the power indicator flashes. At
this time, you can upgrade the firmware through the serial
port, and press the button again to exit the upgrade mode
⑩
TCP/IP
1 x RJ45, TCP/IP control
⑪
DC 24V
Connect DC24V5A power adapter
3.2 Receiver
HDMI AUDIOHOST
L R
DC 24V
HDMI
USB-C TCP/IPHDBT
INPUT OUTPUT
RS232
Tx Rx
LOCAL
PASS
Tx Rx
SM BO
GR 1
GR 2
SM BO
60W
1 2 3 4 5 6 7 8 910 11

18Gbps HDMI+USB-C KVM Switcher KIT
7
Front Panel
No.
Name
Description
①
OUTPUT
⚫1 x HDMI output;
⚫1 x 5-pin balanced audio output, HDMI output audio de-
embedding
②
DEVICES
3 x USB-A 2.0, 1 x USB-C, connect keyboard, mouse,
microphone, printer, camera and other equipment
Rear Panel
No.
Name
Description
①
ETHERNET
1 x RJ45, used for network passthrough transmission
②
HDBT IN
1 x RJ45 interface, the green light is always on when the
signal is with HDCP, flashes when the input signal is not
HDCP; the yellow light is always on after the TX and RX are
connected
③
RS232
1 x 3-pin phoenix head, RS232 passthrough transmission
④
Power LED
1 x green indicator light, always on when machine is working
⑤
DC 24v
Connect DC24V5A power adapter
DEVICES
21
4
3
HDMI AUDIOHDMI AUDIO
OUTPUT L R
1 2
RS232
Tx Rx
DC 24V
ETHERNET HDBT IN
1 2 3 4 5

18Gbps HDMI+USB-C KVM Switcher KIT
8
4. EDID Management
EDID are control by the EDID DIP switch, the specific description is as follows:
0000 Learn the display EDID in the default mode: read the EDID of the TX HDMI output
and RX HDMI output, and output the EDID with the lower resolution of the two, if you
can’t learn it, then use the built-in 1920x1080@60 8bit Stereo
0001 1920x1080@60 8bit High Definition Audio
0010 3840x2160@60Hz Deep Color Stereo Audio
0011 3840x2160@30Hz 8bit Stereo Audio
0100 3840x2160@30Hz Deep Color High Definition Audio
0101 3840x2160@60Hz 4:2:0 Deep Color Stereo Audio
0110 3840x2160@60Hz Deep Color High Definition Audio
0111 3840x2160@60Hz Deep Color HDR LPCM 6CH
1011 Custom EDID1
1100 Custom EDID2
1101 Custom EDID3
1110 Custom EDID4
1111 EDID management

18Gbps HDMI+USB-C KVM Switcher KIT
9
5. GUI Control
The MP-SU21T-KVM can be controlled via TCP/IP. The default IP settings are:
IP Address:192.168.0.178
Subnet Mask:255.255.255.0
Gateway:192.168.0.1
Please type the IP Address of the control PC in the internet browser, and it will enter the
below log-in webpage.
Username: admin
Password: admin
Please type the username and the password, and then click LOGIN.

18Gbps HDMI+USB-C KVM Switcher KIT
10
5.1 Video Tab
⚫Choose the HDMI, USB-C or Auto source according to actual usage.
5.2 Configuration Tab
5.2.1 EDID
⚫Choose the desired EDID format or define the appropriate EDID format.

18Gbps HDMI+USB-C KVM Switcher KIT
11
5.2.2 Auto Downscale
⚫Enable or disable the auto Downscale in TX or RX output.
5.2.3 HDCP
⚫Choose the HDCP follow the souse or display.

18Gbps HDMI+USB-C KVM Switcher KIT
12
5.2.4 Tags
⚫Choose and enter the tags, then click confirm to change the tags.
5.3 CEC Tab

18Gbps HDMI+USB-C KVM Switcher KIT
13
5.3.1 Input
⚫Select the function and press to control the input
5.3.2 Output
⚫Select the function button and press to control the output

18Gbps HDMI+USB-C KVM Switcher KIT
14
5.3.3 User-defined
⚫Define the Trigger of input and output
5.4 RS232 Tab
⚫Baud Rate: Supports 9600, 19200, 38400, 57600, 115200

18Gbps HDMI+USB-C KVM Switcher KIT
15
⚫Command Ending: NULL, CR, LF or CR+LF can be chosen.
⚫Command: Type the command in the box to control the third-party device which is
connected to the RS232 port of the MP-SU21T-KVM.
5.5 Network Tab
⚫Static IP or Dynamic Host Configuration Protocol (DHCP).
⚫Modify the static IP Address, Subnet Mask, and Gateway.