MIMO TL-ANT2415MS User manual

Installation Guide
2x2 MIMO Sector Antenna
Model: TL-ANT2415MS & TL-ANT5819MS

CONTENTS
Introduction
Specifications
Safety Notice
Package Contents
Installation Requirements
Hardware Overview
Hardware Installation
1
1
2
2
3
3
4

1
Introduction
The TL-ANT2415MS, 2.4GHz 15dBi 2x2 MIMO Sector Antenna, is for use
with the outdoor wireless Base Station WBS210 and achieve a stable
long-distance signal transmission.
The TL-ANT5819MS, 5GHz 19dBi 2x2 MIMO Sector Antenna, is for use
with the outdoor wireless Base Station WBS510 and achieve a stable
long-distance signal transmission.
Specifications
Electrical Specifications TL-ANT2415MS TL-ANT5819MS
Frequency Range
Gain
VSWR
HPOL Beamwidth
VPOL Beamwidth
Elevation Beamwidth
Electrical Downtilt
F/B Ratio
Polarization
Impedance
Connector
2.3~2.7GHz
15dBi
1.8 Max
120°(6dB) & 90°(3dB)
120°(6dB) & 90°(3dB)
8°
0°
25dB Min
Horizontal & Vertical
50Ω
RP-SMA
5.0 - 6.0GHz
19dBi
1.8 Max
120° (6dB) & 90° (3dB)
120° (6dB) & 90° (3dB)
4°
0°
28dB Min
Horizontal & Vertical
50Ω
RP-SMA
Antenna Dimension
Weight
Rated Wind Velocity
Mounting
700×133×57mm
3.5Kg
241Km/h
Pole Mount
Mechanical Specifications

2
Package Contents
Hex Nuts
(M4, Qty.4)
Flat Washers
(φ6, Qty.4)
Spring Washers
(φ6, Qty.4)
Bolts with
Nut and Lock Washer Assemblies
(M8×85, Qty.4)
Bolts with
Nut and Lock Washer Assemblies
(M6×35, Qty.2)
Installation Guide
Installation Guide
Protective Shroud
Adjustable Pole-mount BracketAntenna Mount Bracket
RF Cables
(Qty.2)
Pole-mount Clamps
(Qty.2)
Antenna
Heed all warnings:
Mount the antenna at a safe location, far away from power lines,
lamp posts, and other electrical cables.
Do not mount the antenna in the rain or thunderstorm.
Avoid using this product during an electrical storm. There may be a
remote risk of electric shock from lightning.
For your own safety, please seek a qualified service technician for
assistance.
Safety Notice
2x2 MIMO Sector Antenna
Model:TL-ANT2415MS & TL-ANT5819MS

3
Hardware Overview
Back View
RF Connectors
Bubble Level
Base Station/
Shroud Lock
Release Lever
Base Station
Mount Bracket
Assembled Side View
Antenna Mount Bracket
Adjustable Pole-mount
Bracket
Protective
Shroud
Outdoor Wireless Base Station (sold separately)
Wrenches
Installation Requirements

4
1. Attach the RF Cables to the Base Station.
2. Attach the Base Station to the Base Station Mount Bracket as follows:
a. Align the mounting tabs on the back of the Base Station with the
four mounting slots on the Base Station Mount Bracket.
b. Slide the Base Station down until it locks into place.
Hardware Installation

5
3. Connect the other ends of the RF Cables to the RF Connectors on the
antenna.
4. Slide the Protective Shroud down over the Base Station until it locks
onto the Base Station Mount Bracket.

6
6. Attach the Adjustable Pole-mount Bracket and Pole-mount Clamps to
the pole using four M8x85 Bolts with Nut and Lock Washer Assemblies.
5. Attach the Antenna Mount Bracket to the four studs located on the
antenna using the Flat Washers, Spring Washers, and Hex Nuts.
Note: Pole diameter ranges from 40mm to 80mm.

7
7. Mount the Antenna Mount Bracket to the Adjustable Pole-mount
Bracket using two M6x35 Bolts with Nut and Lock Washer Assemblies.
8. Adjust the desired elevation angle of the antenna using the scale
marked on the Antenna Mount Bracket, and then tighten the bolt
and nut assemblies.
Note: Do not over-tighten these bolts and nuts to allow angle adjustment later.

COPYRIGHT & TRADEMARKS
Website: http://www.tp-link.com
Tel: [phone]
E-mail: [e-mail]
Specifications are subject to change without notice.
is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands
and product names are trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to
make any derivative such as translation, transformation, or adaptation without permission
from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO.,
LTD. All rights reserved.
7106505334 REV1.0.0