Minebea Intec PR 54 User manual

Single Point load cell PR 54
Installation Manual
Translation of the Original Installation Manual 9499 053 05400 Edition 1.0.0 05/15/2023
Minebea Intec GmbH, Meiendorfer Str. 205 A, 22145 Hamburg, Germany
Phone: [phone] Fax: [phone]

Foreword
Must be followed!
Any information in this document is subject to change without notice and does not represent a commitment on
the part of Minebea Intec unless legally prescribed. This product should only be operated/installed by trained
and qualified personnel. In correspondence concerning this product, the type, name, and release number/serial
number as well as all license numbers relating to the product have to be cited.
Note
This document is partially protected by copyright. It may not be changed or copied, and it may not be used
without purchasing or written permission from the copyright owner (Minebea Intec). The use of this product
constitutes acceptance by you of the abovementioned provisions.

Table of contents
1 Introduction......................................................................................................................................... 3
1.1 Read the manual......................................................................................................................................................... 3
1.2 This is what operating instructions look like .......................................................................................................... 3
1.3 This is what lists look like........................................................................................................................................... 3
1.4 This is what menu items and softkeys look like..................................................................................................... 3
1.5 This is what the safety instructions look like.......................................................................................................... 3
1.6 Hotline.......................................................................................................................................................................... 4
2 Safety instructions...............................................................................................................................5
2.1 General notes .............................................................................................................................................................. 5
2.2 Intended use................................................................................................................................................................ 5
2.3 Initial inspection.......................................................................................................................................................... 5
2.4 Before operational startup........................................................................................................................................ 5
3 Specifications ......................................................................................................................................6
3.1 Equipment supplied with the load cell....................................................................................................................6
3.2 General information...................................................................................................................................................6
3.3 Possible marking of the load cell for the Ex area .................................................................................................. 7
3.4 Dimensions .................................................................................................................................................................. 8
3.5 Ordering information.................................................................................................................................................8
3.6 Technical data ............................................................................................................................................................9
4 Installation.......................................................................................................................................... 11
4.1 Safety instructions..................................................................................................................................................... 11
5 Connection..........................................................................................................................................12
5.1 General information ..................................................................................................................................................12
5.2 Load cell ......................................................................................................................................................................13
5.3 Load cell cable............................................................................................................................................................13
5.4 Cable gland................................................................................................................................................................ 14
6 Maintenance/repairs/cleaning............................................................................................................15
6.1 Maintenance...............................................................................................................................................................15
6.2 Repairs.........................................................................................................................................................................15
6.3 Cleaning ......................................................................................................................................................................15
7 Disposal ............................................................................................................................................. 16
8 Certificates .........................................................................................................................................17
8.1 CE-00047A ................................................................................................................................................................ 18
8.2 UKCA-00006.............................................................................................................................................................24
8.3 17-046A1 ....................................................................................................................................................................25
8.4 10054..........................................................................................................................................................................28
Single Point load cell PR 54 Table of contents
Minebea Intec EN-1

8.5 R60/2000-NL1-17.45...............................................................................................................................................29
8.6 TC11009.......................................................................................................................................................................31
8.7 BVS 21 ATEX E 023X .................................................................................................................................................34
8.8 IECEx BVS 21.0024X.................................................................................................................................................42
Single Point load cell PR 54 Table of contents
EN-2 Minebea Intec

1 Introduction
1.1 Read the manual
-Please read this manual carefully and completely before using the product.
-This manual is part of the product. Keep it in a safe and easily accessible location.
1.2 This is what operating instructions look like
1. - n. are placed before steps that must be done in sequence.
1.3 This is what lists look like
-indicates an item in a list.
1.4 This is what menu items and softkeys look like
[ ] frame menu items and softkeys.
Example:
[Start]- [Applications]- [Excel]
1.5 This is what the safety instructions look like
Signal words indicate the severity of the danger involved when measures for preventing
hazards are not followed.
DANGER
Warning of personal injury
DANGER indicates death or severe, irreversible personal injury which will occur if the
corresponding safety measures are not observed.
Take the corresponding safety precautions.
WARNING
Warning of hazardous area and/or personal injury
WARNING indicates that death or severe, irreversible injury may occur if appropriate
safety measures are not observed.
Take the corresponding safety precautions.
CAUTION
Warning of personal injury.
CAUTION indicates that minor, reversible injury may occur if appropriate safety
measures are not observed.
Take the corresponding safety precautions.
is placed before a step.
describes the result of a step.
1 Introduction Single Point load cell PR 54
Minebea Intec EN-3