Mini-Circuits UVNA-63 Assembly instructions

PROJECT NO. 1 UVNA- 63
DIY VECTOR NETWORK ANALYZER
Instructions for Assembly
MICROWAVE TRANSCEIVER KIT

WARNINGS AND RECOMMENDATIONS
FOR PROPER USE
WARNING
Electrostatic sensitive device
An 8 lb-in calibrated torque wrench is recommended for
interconnection of components in this kit.
Keep connectors clean from foreign objects and debris to
ensure accurate measurements.
When making SMA connections, always hold the female
connector steady using the anti-torque nut while rotating the
Male SMA connector coupling nut to avoid cross-threading or
damage to the connectors.
Phillips-Head screwdriver
required
2 of 6
AN-49-014 Rev: A M173902 (04/17/19) File: AN49014.pdf
This document and its contents are the property of Mini-Circuits

Refer to BOM for assembly numbers.
Note Please note coupler orientation
ASSEMBLY DIAGRAM ( 2 / 3 )
3 of 6
AN-49-014 Rev: A M173902 (04/17/19) File: AN49014.pdf
This document and its contents are the property of Mini-Circuits

Figure 1
Figure 2 ( 4 Plcs.)
ASSEMBLY DIAGRAM ( 3 / 3 )
4 of 6
AN-49-014 Rev: A M173902 (04/17/19) File: AN49014.pdf
This document and its contents are the property of Mini-Circuits

BILL OF MATERIALS
Description MCL P/N Quantity
1A Tray B12-269-02-1+ 1
1C Transceiver Board TB-UVNA+ 1
1E Clear Cover 0.125" Thick B13-269-02+ 1
16dB High Directivity Coupler ZHDC-16-63-S+ 2
10dB High Directivity Coupler ZHDC-10-63-S+ 2
141 Hand-Flex 3" Cable 141-3SMRSM+ 2
141 Hand-Flex 4" Cable 141-4SM+ 4
141 Hand-Flex 6" Cable 141-6SMR+ 2
141 Hand-Flex 12" Cable 141-12SMR+ 1
Flexible 141 6" Test Cable FL141-6SM+ 2
USB 3.0 CABLE B66-275+ 1
Description MCL P/N Quantity
1B Stand offs
B18-GC-021+
4
1D Spacers B18-RK-006+ 4
1F Short Screws B18-DC-065+ 4
Long Screws B18-DC-113+ 8
Flat Washers B18-HC-001+ 12
Description MCL P/N Quantity
Female - Open B20-64-F6+ 1
Female - Short B20-64-F7+ 1
Female - Load ANNEF-50+ 1
Female - Thru SF-SF50+ 1
Description MCL P/N Quantity
Band Pass Filter, 2450 MHz VBF-2435+ 1
Low Pass Filter, 1500 MHz VLF-1500+ 1
GVA-84 EVAL BOARD TB-410-84+ 1
3 dB Attenuator, 1 Watt VAT-3+ 1
6 dB Attenuator, 1 Watt VAT-6+ 1
15 dB Attenuator, 1 Watt VAT-15+ 1
50 Ohm Termination ANNE-50+ 1
SMA Male - SMA Male Adapter SM-SM50+ 2
SMA Female - SMA Female Adapter SF-SF50+ 2
Description MCL P/N Quantity
SMA Wrench B85-TM-134 1
Kit Components
Assembly parts
Calibration Kit
DUT's
1(Refer Fig. 1)
1(Refer Fig. 1)
-
-
Assembly No.
2(Refer Fig. 2)
3(Refer Fig. 2)
4
5
6
-
-
Supplemental
-
-
Assembly No.
-
-
-
-
-
-
-
Assembly No.
Assembly No.
-
-
2A or 3A
-
Assembly No.
-
-
5 of 6
AN-49-014 Rev: A M173902 (04/17/19) File: AN49014.pdf
This document and its contents are the property of Mini-Circuits

IMPORTANT NOTICE
© 2019 Mini-Circuits
This document is provided as an accommodation to Mini-Circuits customers in connection with Mini-Circuits parts only. In that regard, this document is for informational and guideline purposes only. Mini-
Circuits assumes no responsibility for errors or omissions in this document or for any information contained herein. Mini-Circuits may change this document or the Mini-Circuits parts referenced herein
(collectively, the “Materials”) from time to time, without notice. Mini-Circuits makes no commitment to update or correct any of the Materials, and Mini-Circuits shall have no responsibility whatsoever on account
of any updates or corrections to the Materials or Mini-Circuits’ failure to do so. Mini-Circuits customers are solely responsible for the products, systems, and applications in which Mini-Circuits parts are
incorporated or used. In that regard, customers are responsible for consulting with their own engineers and other appropriate professionals who are familiar with the specific products and systems into which
Mini-Circuits’ parts are to be incorporated or used so that the proper selection, installation/integration, use and safeguards are made. Accordingly, Mini-Circuits assumes no liability therefore. In addition, your
use of this document and the information contained herein is subject to Mini-Circuits’ standard terms of use, which are available at Mini-Circuits’ website at www.minicircuits.com/homepage/terms_of_use.html.
Mini-Circuits and the Mini-Circuits logo are registered trademarks of Scientific Components Corporation d/b/a Mini-Circuits. All other third-party trademarks are the property of their respective owners. A
reference to any third-party trademark does not constitute or imply any endorsement, affiliation, sponsorship, or recommendation: (i) by Mini-Circuits of such third-party’s products, services, processes, or other
information; or (ii) by any such third-party of Mini-Circuits or its products, services, processes, or other information.
AN-49-014 Rev: A M173902 (04/17/19) File: AN49014.pdf
This document and its contents are the property of Mini-Circuits 6 of 6