miniature aircraft X-Cell Whiplash User manual

A
s
s
e
m
b
l
y
I
n
s
t
r
u
c
t
i
o
n
s
Electric
Helicopter Kit
MA1032 Flybar
MA1032-1 Flybarless
Step up to excellence with X-Cell

Table of Contents
Kit Introduction.................................................................................................................................. 3
R/C Helicopter Safety........................................................................................................................ 3
Warning...................................................................................................................................................3
General Guidelines .................................................................................................................................3
Academy of Model Aeronautics (AMA) ........................................................................................... 4
Kit Assembly...................................................................................................................................... 5
Required Tools ........................................................................................................................................5
Other Required Components ..................................................................................................................5
Assembly Tips ................................................................................................................................... 6
Kit Contents ....................................................................................................................................... 7
Flybarless Head Assembly (Whiplash Kit #MA1032-1) .................................................................... 9
Flybarless Head Parts List ......................................................................................................................9
Flybarless Head Assembly Instructions ................................................................................................10
Flybarless Head Link Lengths...............................................................................................................11
Flybar Head Assembly (Whiplash Kit #MA1032) ............................................................................ 12
Flybar Head Parts List ..........................................................................................................................12
Flybar Head Assembly Instructions.......................................................................................................13
Flybar Head Link Lengths .....................................................................................................................16
Tail Assembly................................................................................................................................... 17
Tail Assembly Parts List ........................................................................................................................17
Tail Assembly Instructions.....................................................................................................................18
Electric Frame Assembly................................................................................................................ 23
Electric Frame Assembly Parts List ......................................................................................................23
Electric Frame Assembly Instructions ...................................................................................................24
Electronics Mounting Positions .............................................................................................................32
Electronic Speed Control Mounting Positions.......................................................................................32
Canopy Mounting..................................................................................................................................33
Basic Model/Radio Set Up ..............................................................................................................34
Swashplate eCCPM Set Up............................................................................................................. 35
Pitch Curve Set Up ..........................................................................................................................36
Throttle Curve Set Up...................................................................................................................... 37
Choosing Your Power System ....................................................................................................... 37
Flybarless Stabilization Electronics .............................................................................................. 37
Kit Hardware and Parts................................................................................................................... 38
Warranty Information ...................................................................................................................... 39
2

Kit Introduction
Thank you for purchasing the X-Cell Whiplash by Miniature Aircraft USA. This model is the culmination of
years of designing and manufacturing R/C helicopters. It is designed with the highest standards, and will
provide years of enjoyment. Whether this is your rst R/C model helicopter or you are an advanced R/C
helicopter modeler, the X-Cell Whiplash is a fantastic choice for a “700 size” model.
R/C Helicopter Safety
A radio controlled model helicopter is not a toy, but rather a technically complex device that must be built
and operated with care. It is also a fascinating and challenging part of the R/C sport, the mastery of which
is very rewarding. A model helicopter must be built exactly in accordance with the building instructions. The
kit manufacturer has spent much time and effort rening his product to make it reliable in operation and easy
to build. The essentially bolt together construction can proceed quite rapidly, giving the builder a strong
sense of accomplishment that encourages hasty progress from one construction phase to the next, so that
the completed model can be more quickly seen and enjoyed. It is essential to recognize and guard against
this tendency. Follow building instructions exactly. Vibration and stress levels are high and all fasteners and
attachments must be secure for safe operation.
Note that this is the rst use of the word SAFETY in these comments. Previously the kit manufacturer’s efforts
to ensure reliable operation were mentioned. That is ALL that he can do. Safe operation is the responsibility
of the builder/yer and starts with careful construction and continues with selection and installation of reliable
radio equipment and engine.
The need for safety is nowhere greater than at the ying eld. A number of guidelines for safe ight have
been developed by experienced yers and are set down here. It is urged that they be read, understood and
followed.
Warning! – Risk of death or serious injury
Remote Control (“R/C”) Helicopters can be dangerous. Inexperienced pilots of R/C Helicopters should
be trained and supervised by experienced operators. All operators should use safety glasses and other
appropriate safety equipment. All operators should exercise necessary precautions when fueling, repairing,
maintaining, ying and storing R/C Helicopters, and when using or storing R/C Helicopter accessories,
equipment, fuels, and related materials. R/C Helicopters should be used only in open areas free of obstacles
and far enough from people to minimize the possibility of injury from the helicopter or any of its components
falling or ying in unexpected directions.
This helicopter is not a toy but a complex ying machine that must be assembled with care by a responsible
individual. Failure to exert care in assembly, or radio or accessory installation, may result in a model
incapable of safe ight or ground operation. Rotating components are an ever present danger and source of
injury to operators and spectators. Since the manufacturer and his agents have no control over the proper
assembly and operation of his products, no responsibility or liability can be assumed for their use.
General Guidelines for Safe R/C Helicopter Flight
• Fly only at approved ying elds and obey eld regulations.
• Follow frequency control procedures. Interference can be dangerous to all.
• Know your radio. Check all transmitter functions before each ight.
• Be aware that rotating blades are very dangerous and can cause serious injury.
• Never y near or above spectators or other modelers.
• If you’re a beginner, get help trimming the model rst and ight training later.
• Don’t “track” the main blades by holding the tail boom. This is a temptation to builders who cannot hover
yet and is very dangerous.
• Follow all recommended maintenance procedures for model, radio and engine.
3

Academy of Model Aeronautics
Miniature Aircraft USA highly recommends joining the Academy of Model Aeronautics (AMA).
• AMA is the Academy of Model Aeronautics.
• AMA is the world’s largest model aviation association, representing a membership of more than 150,000
from every walk of life, income level and age group.
• AMA is a self-supporting, non-prot organization whose purpose is to promote development of model
aviation as a recognized sport and worthwhile recreation activity.
• AMA is an organization open to anyone interested in model aviation.
• AMA is the ofcial national body for model aviation in the United States. AMA sanctions more than a
thousand model competitions throughout the country each year and certies ofcial model ying records
on a national and international level.
• AMA is the organizer of the annual National Aeromodeling Championships, the world’s largest model
airplane competition.
• AMA is the chartering organization for more than 2,500 model airplane clubs across the country. AMA
offers its chartered clubs ofcial contest sanction, insurance and assistance in getting and keeping ying
sites.
• AMA is the voice of its membership, providing liaison with the Federal Aviation Administration, the Federal
Communications Commission, and other government agencies through our national headquarters in
Muncie, Indiana. AMA also works with local governments, zoning boards and parks departments to
promote the interests of local chartered clubs.
• AMA is an associate member of the National Aeronautic Association. Through NAA, AMA is recognized by
the Fédération Aéronautique Internationale (FAI), the world governing body of all aviation activity, as the
only organization which may direct U.S. participation in international aeromodeling activities.
For more detailed information, contact the Academy of Model Aeronautics
5161 E. Memorial Drive, Muncie, Indiana, 47302
or telephone [phone].
You may also visit the AMA website at www.modelaircraft.org
4

Kit Assembly
Your Whiplash kit will require a number of different supplies and tools to ensure the best nal result. They
are as follows:
Required Lubricants and Compounds:
1. Medium Strength Thread Locking Compound - X-Cell Super Lock Blue (MA3200-20)
2. Tri-Flow Oil (MA3200-02)
3. Tri-Flow Synthetic Grease (MA3200-06)
4. Medium Cyanoacrylate (CA)
5. Retaining Compound - X-Cell Super Lock Green (MA3200-22)
Required Tools:
1. m4 Nut Driver
2. m5 Nut Driver
3. m5.5 Nut Driver
4. m7 Nut Driver
5. 1.5mm Allen Driver
6. 2.0mm Allen Driver
7. 2.5mm Allen Driver
8. 3.0mm Allen Driver
9. 4.0mm Allen Driver x2
10. 5.0mm Allen Driver
11. Needle Nose Pliers
12. Phillips Screwdriver
13. Razor Knife (X-acto)
14. Rotary Tool w/Grinding Bit
Other required components:
The X-Cell Whiplash is an airframe kit. To complete the model, several other items are required but are not
included with the kit. There are many choices for these other required components, and any competent
hobby retailer with R/C helicopter experience will be happy to make suggestions. You will need:
1. Brushless electric motor KV Range approx 500-530kv suitable for use with a “.90”/700 size model,
with 6mm shaft diameter.
2. Electronic Speed Control (ESC) suitable for use in R/C helicopters, approx 100 Amp HV or better is
recommended.
3. Lithium Polymer Batteries: 6 cell 5000mah x 2 (12 cell LiPo) are recommended. Maximum battery
width 2”.
4. Cyclic servos (Miniature Aircraft USA recommends high quality digital cyclic servos with no less than
80 oz. in. of torque.)
5. R/C helicopter gyro (Miniature Aircraft USA recommends for Flybarless Kits a ybarless electronic
unit with rudder gyro and for Flybar Kits only a tail “heading hold” style gyro is needed)
6. Rudder servo suitable for use with the gyro you choose. Digital servo is recommended.
7. R/C helicopter transmitter and receiver with at least 6 channels, and eCCPM capabilities.
8. Receiver battery pack or suitable BEC.
9. 690-710mm Main Blades and 105mm Tail Blades
5

Important Assembly Tips - PLEASE READ
• Follow the instructions. The methods of construction documented in this manual have been proven to
work. Do not rush the build of your model! You have purchased a world class model helicopter kit, take
your time and realize that the nal result is now up to you. Take the time to fully understand each step and
if you are unsure please contact Miniature Aircraft USA.
• Follow the order of assembly. The instructions have been organized into major sections and have been
written in such a way that each step builds upon the work done in the previous step. Changing the order of
assembly may result in unnecessary steps.
• Clean all metal parts. All of the steel parts in this kit are coated with a lubricant to prevent them from
rusting. This coating can interfere with the adhesives and thread locks needed for assembly. Use a solvent
such as alcohol or acetone to clean the various metal parts, especially threads. Be sure not to overtighten
bolts as damage to bearings and other components will occur.
• It is very important to lightly sand the edges of all carbon ber pieces. Miniature Aircraft USA recommends
doing so prior to the assembly process. Carbon ber edges are sharp and can easily cut component wires
and battery mounting straps. It is important to use safety precautions when creating carbon ber dust.
The use of a particulate mask, preferably one with a P100 HEPA lter is recommended. Always clean up
carbon ber dust with a damp rag right away.
• Use thread lock as indicated. Generally any bolt or screw that threads into a metal part requires thread
lock. Model helicopters are subject to vibration and failing to use thread lock on any non-locking assembly
may result in a part becoming loose or falling off.
6

Bag Part No. Part Description Qty
1-A 0869 Washout Link 2
1-A 128-176 Washout Pin 2
1-A 128-195 Head Button 1
1-A 128-314 Swashplate Follower 2
1-A 131-187 Head Axle 1
1-A 131-190 Damper (80D) 2
1-A 131-368 FBL Head Block 1
1-B 0133-1 M3x21.2 Ball Link 10
1-B 0217 Swashplate 1
1-B 121-4 Servo To Swash Linkage Rod 3
1-B 121-7 Swash To PA Linkage Rod 2
1-B 131-308 FBL Main Shaft 1
1-C 131-161 Main Blade Grip 2
1-C 131-163 FBL Pitch Arm 2
Bag Part No. Part Description Qty
1-Hardware 0021 M4 Lock Nut 1
1-Hardware 0023 M5 Nut 2
1-Hardware 0051 M3x3 Set Screw 3
1-Hardware 0061 M3x8 Socket Bolt 4
1-Hardware 0063 M3x10 Socket Bolt 2
1-Hardware 0064-4 M3x16 Button Head Socket Bolt 2
1-Hardware 0067 M3x14 Socket Bolt 1
1-Hardware 0082-4 M5x32 Shouldered Socket Bolt 2
1-Hardware 0086-1 M5x16 Flanged Socket Bolt 2
1-Hardware 0107 M3x6 Threaded Steel Ball 5
1-Hardware 0109 M3x8 Threaded Steel Ball 4
1-Hardware 0447-1 M2 E-clip 2
1-Hardware 120-7 5x15 C/F Safety Washer 2
1-Hardware 131-83 Anti-rotation Pin 1
1-Hardware 131-184 C/F Damper Washer 2
1-Hardware 131-200 M4x33 Shouldered Socket Bolt 1
Kit Contents
Please take some time to familiarize yourself with the contents of the kit. The Whiplash kit has been broken down into
three “bags”. Each bag contains parts and hardware. The hardware for each bag will be used only for that bag. There
will be no left over parts after each bag is assembled. The individual parts of the factory assembled parts are not listed
out here. They can be found in the components section of the manual.
Bag 1 - Flybarless Kits (MA1032-1)
Bag Part No. Part Description Qty
1-A 0133-1 M3x21.2 Ball Link 4
1-A 121-4 Servo To Swash Rod 2
1-A 128-189 Cage Bar 2
1-A 128-195 Head Button 1
1-A 131-155 Cage End 2
1-A 131-168 FB Head Block 1
1-A 131-187 Head Axle 1
1-A 131-190 Damper (80D) 2
1-B 120-7 5x15 C/F Safety Washer 2
1-B 128-196 Alumimum Bell Mixer 2
1-B 131-161 Main Blade Grip 2
1-B 131-162 FB Pitch Arm 2
1-B 131-184 9x14x.080 C/F Damper Washer 2
1-C 0217 Swashplate 1
1-C 0219 Washout Center Hub 1
1-C 0869 Washout Link 2
1-C 106-05 Washout Arm 2
1-C 128-176 Washout Pin 2
1-C 131-8 FB Main Shaft 1
1-D 0133 M2x21.2 Ball Link 2
1-D 0133-1 M3x21.2 Ball Link 10
1-D 0135 M2x16.4 Ball Link 2
Bag Part No. Part Description Qty
1-D 0313 M2x10 Threaded Control Rod 2
1-D 120-25 Swash To Mixer Linkage Rod 2
1-D 121-4 Servo To Swash Linkage Rod 3
BOX 0303 Flybar 1
1-Hardware 0021 M4 Lock Nut 1
1-Hardware 0023 M5 Nut 2
1-Hardware 0050-1 M2.5 Set Screw 2
1-Hardware 0051 M3x3 Set Screw 3
1-Hardware 0057 M4x4 Set Screw 2
1-Hardware 0061 M3x8 Socket Bolt 4
1-Hardware 0063 M3x10 Socket Bolt 2
1-Hardware 0064-3 M3x6 Button Head Socket Bolt 4
1-Hardware 0067 M3x14 Socket Bolt 3
1-Hardware 0071 M3x18 Socket Bolt 2
1-Hardware 0082-4 M5x32 Shouldered Socket Bolt 2
1-Hardware 0086-1 M5x16 Flanged Socket Bolt 2
1-Hardware 0107 M3x6 Threaded Steel Ball 5
1-Hardware 0109 M3x8 Threaded Steel Ball 6
1-Hardware 0112 M3x9.5 Threaded Steel Ball 4
1-Hardware 0447-1 M2 E Clip 2
1-Hardware 131-83 Anti Rotation Pin 1
1-Hardware 131-200 M4x33 Shouldered Socket Bolt 1
Bag 1 - Flybar Kits (MA1032)
7

Bag Part No. Part Description Qty
2-A 0133 M2x21.2 Ball Link 2
2-A 128-144 T/R Control Rod Guide 4
2-A 131-57 Torque Tube Ends 2
2-A 131-58 Torque Tube 1
2-A 131-62 Tail Boom 1
2-A 131-69-1 T/R Control Rod 1
2-A 131-80 Torque Tube Bearing Cup 2
2-A 131-81 Torque Tube Bearing Cup O-ring 4
2-A 131-86 Assembled Boom Support 2
2-B 131-34 Front Tail Transmission 1
2-B 131-35 Boom Clamp W/TX Holes 1
2-B 131-64 T/R Hub 1
2-B 131-75 T/R Pitch Slider Assembly 1
2-B 131-112 T/R Blade Grip 2
2-B 131-129 Tail Box 1
2-B 131-130 Tail Pitch Control Bellcrank 1
2-B 131-131 C/F Bellcrank Bracket 1
2-B 131-132 Bellcrank Slider Cup 1
Bag Part No. Part Description Qty
2-C 128-80 Front Boom Clamp 1
2-C 128-149a Upper Rear Boom Support Mount 1
2-C 128-149b Lower Rear Boom Support Mount 1
2-C 131-60 C/F Tail Fin 1
2-C 131-128 C/F Boom Clamp Plate 1
2-Hardware 0009 M3 Washer 2
2-Hardware 0016-1 M4 External Serrated Lock Washer 2
2-Hardware 0019 M3 Lock Nut 3
2-Hardware 0056 M3x5 Dog-Point Set Screw 2
2-Hardware 0059-0 M2.5x4 Socket Bolt 6
2-Hardware 0059-1 M2.5x6 Socket Bolt 1
2-Hardware 0060-1 M3x6 Socket Bolt 4
2-Hardware 0061 M3x8 Socket Bolt 3
2-Hardware 0064-3 M3x6 Button Head Socket Bolt 2
2-Hardware 0065 M3x12 Socket Bolt 6
2-Hardware 0067 M3x14 Socket Bolt 2
2-Hardware 0069 M3x16 Socket Bolt 2
2-Hardware 0073 M3x20 Socket Bolt 1
2-Hardware 0078 M4x12 Socket Bolt 2
2-Hardware 0107 M3x6 Threaded Steel Ball 4
Bag 2 - Tail Assembly
Bag Part No. Part Description Qty
3-A 131-29 C/F X-Brace 1
3-A 131-47 C/F Servo Rail Spacer 2
3-A 131-53 C/F Gyro Plate 1
3-A 131-55 C/F Angled Battery Tray 1
3-A 131-153 C/F Canopy Breakaway Tabs 4
3-A 131-186 C/F Anti-rotation Bracket 1
3-A 132-51 C/F Left Frame - Electric 1
3-A 132-53 C/F Right Frame - Electric 1
3-A 132-57 C/F Battery Tray 1
3-A 132-58 C/F Bottom Plate 1
3-A 132-59 C/F Front Doubler - Electric 2
3-A 132-60 C/F Rear Doubler - Electric 2
3-B 0107 M3x6 Threaded Steel Ball 2
3-B 128-57 Tray Mount 7
3-B 128-58 Main Frame Spacer 3
3-B 131-20 Middle Main Shaft Bearing Block 1
3-B 131-21 Upper Main Shaft Bearing Block 1
3-B 131-46 P/A Servo Rail 2
3-B 131-40 Bottom Main Shaft Bearing Block 1
3-B 131-52 Delrin Tray Mount 2
3-B 131-54 M4 Tray Mount 2
3-B 131-107 T/R Bellcrank Swing Arm 1
3-B 131-109 Swing Arm Pivot Mount 1
3-C 131-1 124T Main Gear 1
3-C 131-24 Main Gear Hub 1
3-C 131-150 Front Canopy Post 2
3-C 132-4 Sprag Cup Assembly 1
3-C 132-14 14T Pinion 1
3-C 132-101 Lower Pinion Bearing Block 1
3-C 132-100 X-Block/Motor Mount 1
3-D 0116 M2.5 Threaded Steel Ball 4
3-D 0133 M2x21.2 Ball Link 2
3-D 0390 Large Wire Retainers 3
3-D 106-22 5x11 Grommet 4
3-D 129-49 9/16” Rubber Wire Grommet 1
Bag Part No. Part Description Qty
3-D 128-59 M4 Front Boom Support Spacer 1
3-D 131-50 Elevator Servo Mount 2
3-D 131-69 M2x315 Linkage Rod 1
3-D 131-85 C/F Pushrod Sleeve 1
3-D 131-136 Strut 4
3-D 131-139 Skid Tubes 2
3-D 131-148 Servo Plates 12
3-D 131-151 Rear Canopy Post 2
3-D 131-154 Thumb Screw 4
3-D 3200-46 1/2” Hook & Loop Tape 20”
3-D 3200-54 Adhesive Back Hook & Loop Tape 12”
3-D 3200-56 Battery Straps 4
3-Hardware 0003 M3 Washer 12
3-Hardware 0004 M4 Washer 1
3-Hardware 0016-1 M4 External Serrated Lock Washer 2
3-Hardware 0017-2 M2.5 Hex Nut 4
3-Hardware 0021 M4 Lock Nut 1
3-Hardware 0032 M3 Self Tapping Screw 8
3-Hardware 0057 M4x4 Set Screw 6
3-Hardware 0059-1 M2.5 x6 Socket Bolt 4
3-Hardware 0059-3 M2.5x10 Socket Bolt 16
3-Hardware 0060-1 M3x6 Socket Bolt 18
3-Hardware 0061 M3x8 Socket Bolt 62
3-Hardware 0063 M3x10 Socket Bolt 12
3-Hardware 0064-3 M3x6 Button Head 12
3-Hardware 0069 M3x16 Socket Bolt 1
3-Hardware 0078-4 M4x8 Socket Bolt 4
3-Hardware 0081 M4x16 Socket Bolt 6
3-Hardware 0088 M3x8 Tapered Socket Bolt 5
3-Hardware 131-201 M4x25 Shouldered Socket Bolt 1
BOX 131-152 Whiplash Canopy 1
BOX 132-230 Whiplash Electric Instruction Manual 1
BOX 3000-73 MA Towel 1
Bag 3 - Electric Frame Assembly
8

0107
M3x6 Threaded Steel
Ball
0109
M3x8 Threaded Steel
Ball
0133-1
M3x21.2 Ball Link
0159
3x7x3 Bearing
0217
Swashplate 0447-1
E-Clip
0597-4
M3x4.75x.215 Brass
Spacer
0869
3D Washout Link
120-7
M5x15 Carbon Fiber
Safety Washer
121-4
M3x30 Threaded
Control Rod
121-7
M3x65 Threaded
Control Rod
128-176
M2x.584 Washout
Pivot Pin
128-195
Aluminum Head Button
131-83
Swashplate Pin
131-161
Aluminum Blade Grip
131-163
Aluminum Pitch Arm
131-182
9x17x5 Thrust Bearing
131-184
Carbon Fiber Damper
Washer
131-187
Head Axle
131-200
M4x33 Shouldered
Socket Bolt
131-308
Flybarless Main Shaft
131-190
Damper (80D)
131-181
9x17x5 Bearing
0023
M5 Hex Locknut
0061
M3x8 Socket Bolt
0064-4
M3x16 Button Head
Socket Bolt
0067
M3x14 Socket Bolt
0051
M3x3 Socket Set
Screw
131-368
Flybarless Head Block
131-183
9x14x.75 Washer
128-314
Swashplate Follower
MA1032-1 - Flybarless Head Assembly Parts
Apply a small amount of
medium thread lock when
threading into metal parts
Hardware for
this assembly
0051
0051
0109
0109
0109
0109
0107
0107
0107
131-83
0082-4
M5x32 Shouldered
Socket Bolt
0086-1
M5x16 Flanged Bolt
Assembly Tip
• Install MA0051 M3x3 Socket Set
Screws only until they bottom out
against the lower bearing. No not
overtighten or damage to swashplate
bearing will occur.
0217
0021
M4 Hex Locknut
0063
M3x10 Socket Bolt
0107 x 3
M3x6 Threaded
Steel Ball
0109 x 4
M3x8 Threaded Steel
Ball
0051 x 3
M3x3 Socket Set
Screw
131-83 x 1
Swashplate Pin
9

131-184
131-181
131-182
Large
I.D. Small
I.D.
131-183
131-181
120-7
0086-1
Bearings Factory Installed
in Blade Grips
Hardware for
this assembly
Assembly Tip
Apply a small amount of
medium thread lock when
threading into metal parts
0107
0061
131-163
131-161
• The use of a light grease such as
MA3200-06 Tri-Flow Synthetic Grease
is required for damper/head axle
lubrication
• The use of a light grease
such as MA3200-06 Tri-Flow
Synthetic Grease is required
for thrust bearing lubrication
(pre-applied and assembled
from factory)
• 3 piece thrust bearing
(MA131-182) outer race with
larger I.D. (inside diameter)
installs closest to hub.
Assembly Tips
X2
131-190
131-190
131-187
128-195
0067
0159
0159
0597-4
128-314
0064-4
128-176
0869
0447-1
131-368
Factory Installed
Apply
grease to
Head Axle
X2
Hardware for
this assembly
0107 x 2
M3x6 Threaded
Steel Ball
0061 x 4
M3x8 Socket Head
Cap Screw
0086-1 x 2
M5x16 Flanged Bolt
0064-4 x 2
M3x16 Button Head
Socket Bolt
0067 x 1
M3x14 Socket Bolt
0447-1 x 2
E-clip
128-176 x 2
M2x.584 Washout
Pivot Pin
120-7 x 2
M5x15 Carbon Fiber
Safety Washer
131-184 x 2
Carbon Fiber Damper
Washer
131-183 x 2
9x14x.75 Washer
10

0082-4
0023
0023
131-200
0021
0063
0063
131-308
Hardware for
this assembly
0133-1
0133-1
121-7
0133-1
0133-1
121-4
47.5mm
13.5mm
Apply a small amount of
medium thread lock when
threading into metal parts
Link Arm
Lengths and
Installation
X2
X3
0023 x 2
M5 Hex Locknut
0063 x 2
M3x10 Socket Bolt
0021 x 1
M4 Hex Locknut
0082-4 x 2
M5x32 Shouldered
Socket Bolt
131-200 x 1
M4x33 Shouldered
Socket Bolt
11

MA1032 - Flybar Head Assembly Parts
128-195
Aluminum Head Button
0067
M3x14 Socket Bolt
0071
M3x18 Socket Bolt
0078-3
M4x6 Socket Bolt
0107
M3x6 Threaded Steel Ball
0109
M3x8 Threaded Steel Ball
0112
M3x9.5 Threaded Steel
Ball
0133
M2x21.2 Plastic
Ball Link
0133-1
M3x21.2 Plastic
Ball Link
0135
M2x16.4 Plastic
Ball Link
0219
Washout Center Hub
0217
Swashplate
0283
6x10x3 Flanged Bearing
0303
M4x17.75” Flybar
0313
M2x10 Threaded
Control Rod
106-05
Aluminum Washout Arm
106-02
3x7x3 Flanged Bearing
106-06
2x5x.5 Flanged Bearing
0447-1
E-clip
0869
3D Washout Link
120-7
M5x15 Carbon Fiber
Safety Washer
120-25
M2.6x86 Threaded
Control Rod
128-189
Flybar Control Bar
121-4
M3x30 Threaded Control
Rod
122-28
M3x.125”x.79” Brass
Spacer
128-176
M2x.584 Washout Pivot
Pin
128-196
Aluminum Bell Mixer
131-162
Flybar Pitch Arm
131-83
Swashplate Pin
131-155
Flybar Cage End
131-157
Flybar Cross Tube
131-161
Aluminum Blade Grip
131-166
4x8x3 Flanged Bearing
131-168
Flybar Head Block
131-187
Head Axle
131-190
Damper (80D)
131-182
9x17x5 Thrust Bearing
131-181
9x17x5 Bearing
131-183
9x14x.75 Washer
131-184
Carbon Fiber Damper
Washer
131-8
Flybar Main Shaft
0840-27
Washout Head Pin
0159
3x7x3 Bearing
0082-4
M5x32 Shouldered
Socket Bolt
0086-1
M5x16 Flanged Bolt
131-200
M4x33 Shouldered
Socket Bolt
0051
M3x3 Socket Set
Screw
0021
M4 Hex Locknut
0023
M5 Hex Locknut
0057
M4x4 Socket Set
Screw
0050-1
M2.5x3 Socket Set
Screw
0061
M3x8 Socket Bolt
0064-3
M3x6 Button Head
Socket Bolt
0063
M3x10 Socket Bolt
12

Assembly Tip
Hardware for
this assembly 0051
0051
0112
0109
0109
0112
0107
0107
0107
131-83
Apply a small amount of
medium thread lock when
threading into metal parts
0071
106-05
0109
106-02
0159
122-28
106-06
(factory installed)
0869
128-176
0447-1
0219
0061
0109 0050-1
(Install last)
0067
106-02
106-02
122-28 0107
131-161
131-162
128-196
Hardware for
this assembly
Factory Installed
Apply a small amount of
medium thread lock when
threading into metal parts
Hardware for
this assembly
Assembly Tip
• Do not overtighten MA0071 Socket
Bolt into plastic Washout Center Hub.
0061
Factory
Installed X2
X2
• Install MA0051 M3x3 Socket Set
Screws only until they bottom out
against the lower bearing. No not
overtighten or damage to swashplate
bearing will occur.
0217
0107 x 3
M3x6 Threaded
Steel Ball
0109 x 2
M3x8 Threaded Steel
Ball
0112 x 2
M3x9.5 Threaded
Steel Ball
0051 x 3
M3x3 Socket Set
Screw
131-83 x 1
Swashplate Pin
0109 x 2
M3x8 Threaded Steel
Ball
0071 x 2
M3x18 Socket Bolt
0107 x 2
M3x6 Threaded
Steel Ball
0109 x 2
M3x8 Threaded Steel
Ball
0050-1 x 2
M32.5x3 Socket Set
Screw
0447-1 x 2
E-clip
128-176 x 2
M2x.584 Washout
Pivot Pin
0061 x 4
M3x8 Socket Bolt
0067 x 2
M3x14 Socket Bolt
13

0078-3
131-190
131-187
128-195
0067
131-168
131-166
0078-3
131-166
0283
0283
0112
0112
131-157
131-190
0840-27
(factory installed)
Hardware for
this assembly
Apply a small amount of
medium thread lock when
threading into metal parts
0064-3
0064-3
131-155
128-189
131-155
128-189
0133-1
0133-1
121-4
17.5mm
Bearings and Cross
Tube Factory Installed
into Head Block
Hardware for
this assembly
Assembly Tip
• The use of a light grease such as
MA3200-06 Tri-Flow Synthetic Grease
is required for damper/head axle
lubrication
Apply grease
to Head Axle
X2
0112 x 2
M3x9.5 Threaded
Steel Ball
0067 x 1
M3x14 Socket Bolt
0078-3 x 2
M4x6 Socket Bolt
0064-3 x 4
M3x6 Button Head
Socket Bolt
14

131-184
131-181
131-182
Large
I.D. Small
I.D.
131-183
131-181
120-7
0086-1
131-200
0021
131-8
0063
0063
0057
0303
Bearings Factory Installed
in Blade Grips
Hardware for
this assembly
• The use of a light grease such
as MA3200-06 Tri-Flow Synthetic
Grease is required for thrust
bearing lubrication (pre-applied and
assembled from factory)
• 3 piece thrust bearing (MA131-66)
outer race with larger I.D. (inside
diameter) installs closest to hub.
• Ensure equal lengths of MA0303
Flybar extended out of the ybar
control assembly.
Assembly Tips
Washout Links install
onto longer MA0112
Threaded Steel Balls
X2
0021 x 1
M4 Hex Locknut
0057 x 2
M4x4 Socket Set
Screw
0067 x 2
M5x16 Flanged Bolt
131-200 x 1
M4x33 Shouldered
Socket Bolt
120-7 x 2
M5x15 Carbon Fiber
Safety Washer
131-184 x 2
Carbon Fiber Damper
Washer
131-183 x 2
9x14x.75 Washer
0063 x 2
M3x10 Socket Bolt
15

0082-4
0023
0023
0133-1
0133-1
120-25
0133-1
0133-1
121-4
0135
0133
0313
19mm
72.5mm
Hardware for
this assembly
32mm
X3 X2
X2
0023 x 2
M5 Hex Locknut
0082-4 x 2
M5x32 Shouldered
Socket Bolt
16

Tail Assembly Parts
0060-1
M3x6 Socket
Bolt
0061
M3x8 Socket
Bolt
0064-3
M3x6 Button Head
Socket Bolt
0065
M3x12 Socket
Bolt
0067
M3x14 Socket
Bolt
0107
M3x6 Threaded
Steel Ball
0133
M2x21.2 Ball Links
0159
3x7x3 Bearing
0215
Auto Hub Ret. Collar
0225
Pivot Pin For
Pitch Links
0273
M6x10x.011” Steel
Shim Waasher
0319
8x16x5 Bearing
0442
Pivoting T/R Pitch
Link
120-39
5x10x4 Bearing
122-70
M.5x.25 Shim
127-86
M6x9.7x1.0 Shim
Washer
128-80
Aluminum Front
Boom Clamp
128-144
T/r Control Rod
Guides
131-15
Tail Drive Gear
131-17
Tail Bevel Gear,
Shaft Side
131-18
Tail Bevel Gear,
Torque Tube Side
131-33
15x21x4 Bearing
131-34
Front Tail Drive
Transmission
131-51
Jack Shaft
131-57
Torque Tube End
131-58
Torque Tube
131-62
Aluminum Tail Boom
131-64
Tail Hub
131-66
5x10 Thrust Bearing
131-69-1
Tail Linkage Rod
131-70
Tail Rotor Output
Shaft
131-23
6x13x5 Bearing
128-149
Rear Boom Support
Mount
131-60
Carbon Fiber Vertical
Tail Fin
0009
3mm Flat Steel
Washer
0012-2
M3 Pem Nut
0019
3mm Hex
Locknut
0051
M3x3 Socket Set
Screw
0056
M3x5 Dog Point
Socket Screw
0059-0
M2.5x4 Socket Bolt
0059-1
M2.5x6 Socket
Bolt
0016-1
4mm External
Serrated Lockwasher
131-35 Boom Clamp
W/transmission Holes
0069
M3x16 Socket
Bolt
0058-3
M4x16 Socket Set
Screw
128-146
Aluminum Boom
Support Ends
0078
M4x12 Socket
Bolt
0597-1
3x4.75x.126 Brass
Spacer
131-76
Tail Pitch Yoke
131-77
Brass Slider
131-73
7x11x3 Bearing
131-74
Pitch Slider Ring
131-80
Torque Tube Bearing
Cup
131-81
Torque Tube Bearing
Cup O-ring
131-112
T/R Blade Grip
131-128
Carbon Fiber Boom
Clamp Plate
131-129
Tail Case
131-130
Tail Bellcrank
131-131
Carbon Fiber
Bellcrank Bracket
131-132
Bellcrank Cup
131-135
Bracket Washer
131-84
Carbon Boom
Support Rod
131-86
Tail Boom Support
Assembly
131-78
7mm Retaining Clip
0073
M3x20 Socket
Bolt
17

Apply a small amount of
medium thread lock when
threading into metal parts
Hardware for
this assembly
131-23 131-33
131-129
0051
0215 0273
131-17
0056
0056
131-18
131-70
Factory Assembled
Factory Assembled
Assembly Tip
• Make sure to include MA0273 Shim
Washer between MA131-17 Output
Gear and transmission case bearing.
0051 x 2
M3x3 Socket Set
Screw
0056 x 2
M3x5 Dog Point
Socket Screw
0273 x 2
m6x10x.11” Steel
Shim Washer
0225
0225
0442
131-76
131-73
131-77
131-74
0107
0107 x 1
M3x6 Threaded
Steel Ball
Hardware for
this assembly
0225 x 2
Pivot Pin for Washout
Arm
Factory
Assembled
(not factory installed)
131-78
131-78
7mm Retaining Clip
0273
18

0064-3
0107
0073
0159
131-130
131-132
(This part is not
factory installed)
0059-1
131-131
131-135
0012-2
Hardware for
this assembly
Assembly Tip
Hardware for
this assembly
0009
120-39
122-70
131-66
0069
0019
0107
120-39
131-112
131-64
0061
Small
I.D.
Large
I.D.
Apply a small amount of
medium thread lock when
threading into metal parts
0597-1
Factory
Assembled
Factory
Assembled
Bearings
Factory Installed
in Blade Grips
• The use of a light oil such as
MA3200-02 Tri-Flow Oil is required
for tail rotor output shaft/pitch
slider lubrication
Apply oil to
output shaft
0159
X2
Assembly Tips
• 3 piece thrust bearing (MA131-66)
outer race with larger I.D. (inside
diameter) installs closest to hub.
• Grease the center ball cage of the
thrust bearing. We recommend using
MA3200-06 Tri-Flow synthetic grease.
• Only hand tighten MA0061 Socket
Bolt until it is moderately tight. Do
not overtighten bolt or it may result in
fatigue to bolt. Use green thread lock
on these bolts.
0107 x 1
M3x6 Threaded
Steel Ball
0061 x 2
M3x8 Socket Bolt
0009 x 2
3mm Flat Steel Washer
0019 x 1
3mm Hex Nut
122-70 x 2
M.5x.25 Shim
0069 x 2
M3x16 Socket Bolt
0107 x 2
M3x6 Threaded
Steel Ball
0059-1 x 1
M2.5x6 Socket Bolt
0064-3 x 2
M3x6 Button Head
Socket Bolt
0073 x 1
M3x20 Socket Bolt
0019
0019 x 1
3mm Hex Nut
19

131-18
0065
0065
131-35
0056
0056
Hardware for
this assembly
Apply a small amount of
medium thread lock when
threading into metal parts
Assembly Tip
• Ensure the dog point tip is seated
into the dimples on the tail rotor
shaft.
131-23
131-33
131-34
131-51
131-15
131-17
0273
127-86
0056
0056
0056
Hardware for
this assembly
Factory Assembled
0056 x 2
M3x5 Dog Point
Socket Screw
0056 x 4
M3x5 Dog Point
Socket Screw
0065 x 3
M3x12 Socket Bolt
0273 x 1
M6x10x.011” Steel
Shim Washer
127-86 x 1
M6x9.7x1.0 Shim
Washer
20