miniBatt PRO VR User manual

ENGLISH
1
USER
MANUAL
Model:
miniBatt PRO VR
Thank you for choosing the MINIBATT PRO VR! Always follow
basic safety precautions when using electrical appliances.Read all
instructions carefully, Please keep this instruction manual for easy
reference.

ENGLISH
2
Indicator
Press the switch to check the storage level of MINIBATT PRO VR
A. PRODUCT LAYOUT:
B. OPERATION GUIDANCE:
Indicator Unlit 1 Solid 2 Solid 3 Solid 4 Solid
Storage level 0% 25% 50% 75% 100%
Indicator
Switch
Jump start socket
12V 10A output port
19V 3,5A output port
LED Flash Light
USB5V 1A output port
USB5V 2A output port
15V 1A input port
Car adaptor
P15V 1A input
port
Home adaptor
Jumper cable
with clamps
Jump start socket 19V 3,5A output
port
USB5V 2A output
port
12V 10A output
port
For 12V vehicle
products
A B

ENGLISH
3
The indicator will flash one by one during the period of charging.
Different number of solid indicators show different storage level of
MINIBATT PRO VR. All indicators light off when the charging is paused
or completed.
1. Plug the home adaptor into the universal socket.
2. Connect 15V 1A input port of MINIBATT PRO VR to the other end
of home adaptor.
1. Plug the car adaptor into the socket of cigarette lighter.
2. Connect 15V 1A input port of MINIBATT PRO VR to the other end
of car adaptor.
MINIBATT PRO VR Charging Instruction:
1. Connect smart booster cable to jump starter, it begins to test the
device, and LCD display shows the voltage.
Jump start 12V vehicle Instruction:

ENGLISH
4
2. Connect Red Clamp to the positive (+) battery terminal, Black
Clamp to the negative (-) battery terminal. Cable will test the
voltage and SOH(State of Health) of the battery, show the data on
the display.
3. Operate according to the instruction of the LCD Display:
3.1. When LCD display shows JUMP START READY, indicating
connection is correct and the circuit is working, crank the engine
directly.
3.2. When LCD display shows CLAMPS REVERSED, ALARM RINGS,
indicating the connection is wrong, correct the clamps before
LCD display shows JUMP START READY, then crank the engine
within 30s.
B eep ,Be ep

ENGLISH
5
3.3. When LCD display shows PRESS BOOST BUTTON, ALARM rings,
indicating the voltage of vehicle battery is too low, press the
“BOOST”button until LCD display shows JUMP START READY,
then crank the engine within 30s.
3.4. When LCD shows no data about vehicle battery, no alarm rings,
indicating vehicle battery is dead or removed, confirm clamps are
connected to vehicle battery correct, press the“BOOST”button
until“JUMP START READY”is on, and then crank the engine within
30s.
4. Start the vehicle, LCD display shows PEAK CURRENT xxxA after it is
detected by cable.
5. Remove jumper cable from the vehicle battery after vehicle is
started, leave the engine running.
B eep ,Be ep

ENGLISH
6
1. Plug the switch cable B to USB 5V 2A output port.
2. Select appropriate connector and connect it to your mobile
phones or tablet.
3. Press the switch button to charge.
4. If doesn’t work, please try another USB Output port.
Charging Cell Phone or Tablet Instruction:
1. Plug the switch cable A to USB 19V 3.5A output port.
2. Select appropriate connector for your Notebook and connect it to
the switch cable A and your Notebook.
3. Press the switch button to charge/power supply.
Only for charging/power supply to 19V
Notebook:
1. Plug the optional switch cable to 12V 10A output port.
2. Connect the optional switch cable and 12V vehicle product or
12V electronics.
3. Press the switch button to power supply.
For power supply to 12V vehicle products or
12V electronics:

ENGLISH
7
C. PARTS LIST:
D.TECHNICAL SPECIFICATIONS:
#
2
Parts Name
Switch cable A
Quantity
1
#
6
Parts Name Quantity
1
1Host 1 5 Home adaptor 1
Size: 224x87x29mm
Input: 15V 1A
Weight: 610g
Full charging time: 8 hours
Peak current:： 600A
Battery Capacity: 20000mAh (74Wh)
Output: 5V 1A;5V 2A; 12V 10A; 19V 3.5A;
Starting current: 300A
Operating temperature: -20ºC ~ 60ºC
Press the switch 3 seconds to start the LED flash light.
There are 4 modes of LED light appear in order (normal. strobe. SOS.
off) if you press slightly.
LED flash light
Car adaptor
4 8 8 User Manual 1
1
Intelligent jumper
cable
Switch cable B
Notebook
connector
17
3
Q. How to turn off this appliance?
A. This appliance will power off automatically when no load or
charging is complete.
E. FAQ:

ENGLISH
8
Q. How long time to full charge the MINIBATT PRO VR?
A. Approx. 8 hours through the 15V1A input.
Q. How many times can this appliance charge for my cell phone?
A. Depend on the battery capacity of your cell phone.Take iPhone6
as an example, can full charging 8 times.
Q. How long will this appliance on a full charge take to supply the
Notebook?
A. 4-6 hours.
Q. How many times can this appliance jump start the vehicle if it is
in full battery?
A. Approx. 40 times.
Q. What’s the lifetime of MINIBATT PRO VR?
A. Usually 3-5years in normal condition.
Q. How long does the battery last still can jump start the car after
fully charged?
A. 6-12 months, however, we suggest to recharge it every 3 months.
F.TROUBLE SHOOTING:
Finding Cause Remedies
No response when
pressing the switch
button.
Low voltage protection of
product is started.
Plug the adaptor into
the 15V1A input port to
activate.
MINIBATT PRO VR is a
bit hot when charging
for Notebook.
The charging current is a bit
high (3.5A)
Remove the battery
of your Notebook and
use this appliance to
supply power directly,
or disconnect MINIBATT
PRO VR with your
Notebook and connect
them when it is cool.

ENGLISH
9
G.TOXIC AND HARMFUL SUBSTANCES:
O: Indicate all homogeneous materials’hazardous substances content are below the
MCV limit specified in the Standard 2002/95/EC(RoHs).
Pb
0
Hg
0
Cr (Vi)
0
PBDE
0
Composition and amount of toxic and harmful substances in product.
Cd
0
PBB
0
1. Read the instruction manual carefully before using this unit.
2. Jump for 12V vehicles only, it would be hazard if for other jumping.
It is forbidden to use for other machines such as aircraft,ship and so
on.
3. Caution while using this unit.
4. DO NOT use this unit if any cable clamp or cord is damaged.
5. DO NOT use in place of a vehicle battery.
6. DO NOT use as a battery charger.
7. Never remain the unit on car battery after cranking the car success.
8. Use the jumper cable provided with this unit only.
9. Make sure the BLUE plug of the jumper Cable is plugged fully into
jumping socket, Otherwise, the blue plug would be melted.
H.Warning:

ENGLISH
10
10. Make sure to check all the battery connections are CLEAN before
Jump Starting! Make sure the battery clamps are well connected! If
the battery terminals on the vehicle are dirty or corroded, the power
of the unit will be lessened.
11. DO NOT Jump Start more than 3 times in a row. It could damage
the unit by overheating. Give two minutes between attempts.The
jumping cable can become overheated and detach as a safety
measure.
12. Remove the product from the vehicle battery within 30 seconds
of Jump Starting. If not, it could lead to damage.
13. DO NOT connect the two clamps together.
14. Only jump start when 3 to 4 indicator lights are illuminated.
15. DO NOT use by young or infirm persons without supervision.
16. DO NOT use as a toy.
17. DO NOT allow the product to become wet.
18. DO NOT immerse the product in water.
19. DO NOT operate the product in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust.
20. DO NOT modify or disassemble MINIBATT PRO VR. Only a repair
technician may repair this unit.
21. DO NOT expose product to extreme heat or fire.
22. Make sure someone should be within range of your voice or close
enough to come to your aid when working with batteries.