Minicraft Models USAF WC-130J User manual

WC-130J USAF
The C-130 has been one of the most effective transport and cargo carrying aircraft in history. First
deployed in 1957, the C-130 has been continuously up-dated and evolved into a virtually new aircraft
design with markedly enhanced capabilities. The C-130 has been adapted to serve a variety of missions for
the U.S. Air Force going far beyond the original transport design.
This 1/144 scale model represents the WC-130J assigned to 53rd Weather Reconnaissance Squadron
"Hurricane Hunters". These aircraft make up more than 95 percent of the total flying missions operating
from Keesler AFB in Mississippi.
This kit features new engine and propeller tooling to represent the latest C-130 in service. The kit also
includes recessed panel lines, visible cargo hold, opening rear cargo door and position-able landing gear
and new decals by Cartograf will include markings for 2 403
rd
AW USAF aircraft.
Markings included in this kit are:
U.S. Air Force Reserve, 403rd AW, 2003
U.S. Air Force Reserve, 403rd AW, 2010
Minicraft Models (US) LLC, 1501 Commerce Drive, Elgin IL 60123 USA
www.minicraftmodels.com
Printed in China
14689

486 6 7519 18 12
13
2
10
1
13
12
17 16
15
14 766
8
3
11
'A' FUSELAGE PARTS SPRUES
69
70
71
FUSELAGE SPONSON SPRUE
14589
42
42
86
85
86
85
88 88
8080
J VERSION PARTS SPRUE
42
42
86
85
86
85
88 88
8080
J VERSION PARTS SPRUE

INTERIOR PARTS SPRUE
'C' CLEAR PARTS SPRUE
'B' WING / ENGINE / TANK PARTS SPRUE
21 23
25
37
31 33
29
29
26 26
27 27
28
36
64
66
65
67
68
68
63
20
24
22
39
32
34
35
28
27
27
26 26
43 45
47
46
NOTE
Parts shown in Gray
are not for use
14589

C-130J
Cut out panels as shown.
Inside of both fuselage halves
(Parts 1/2)
WHEEL WELLS
1
All Parts
5
8
2 1
8
Cockpit area FLAT BLACK
or LIGHT GRAY
Cement
Coller
Kleben
Pegar
Incollare
Colar
Kleven
DO NOT Cement
Ne pas Coller
Nicht Kleben
No Pegar
Non Incollare
Nao Colar
Niet Kleven
Cut away
Couper
Scheiden
Cortar
Tagliere
Cortar
Snijden
Optional parts
Choix
Auswahlmoglichkeit
Eleccion
Scelta
Opaco
Keuze
Repeat operation
RŽpeeter l' opŽration
Vorgang wiederholen
Repitir la operacion
Ripetere
Repitir a opera•ao
Herhalen
Symmetrical assembly Drill hole
INTERIOR ASSEMBLY
2
All Parts
67
66
Interior parts LIGHT GRAY or FLAT ALUMINUM

FUSELAGE ASSEMBLY
4
All Parts
69
2
RIGHT FUSELAGE SPONSON
3
All Parts
70
71
1
All Parts
85 86 88
80
NACELLE ASSEMBLY
5
NOTE - Parts are shown upside down for clarity.

All Parts
All Parts
MAIN ASSEMBLY
7
47
43
44
25
24
Port (Left) Navigation Light (44) CLEAR RED
Starboard (Right) Navigation Light (43) CLEAR GREEN
Some parts not shown for clarity
NOTE
Add 8 grams (~.25 oz.)
nose weight
in cockpit area.
WING / EXHAUST ASSEMBLY
6
29
29
23
21
LEFT WING
Exhausts BURNT METAL
Fill holes if not adding external tanks
(Refer to Step 8)
Fill holes
Fill holes if not adding external tanks
(Refer to Step 8)
NOTE - Parts are shown upside down.
29
29
22
20 RIGHT WING
Fill holes

BEAVER TAIL
9
EXTERNAL FUEL TANKS
8
LANDING LIGHTS
10
RIGHT Main gear door Part 4
LEFT Main gear door Part 3
45
46
18
35 39 37 36
All Parts
MAIN LANDING GEAR
11
10 11
66
6
6
12
12
43
12
12
Struts / Hubs / Interiors ALUMINUM
Tires FLAT BLACK
RIGHT MAIN LANDING GEAR LEFT MAIN LANDING GEAR
NOTE - Parts are shown upside down.
All Parts
LEFT WING RIGHT WING
Note: Use of fuel tanks is optional.

All Parts
All Parts
All Parts
CARGO HATCH
13
NOSE LANDING GEAR
12
PROPELLERS
14
15
63
64
42
68
68
65
77
13
19 16
14
13
Interior parts LIGHT GRAY or ALUMINUM
Hub / Blades FLAT BLACK
Strut / Hubs / Interior ALUMINUM
Wheels FLAT BLACK

14589
PAINTS
A Black (ModelMaster 1749, Acryl 4768)
B FS16473 Aircraft Gray (ModelMaster 1731, Acryl 4693)
C FS36173 Air Mobility Command Gray (ModelMaster 2035, Acryl 4754)
U.S. Air Force Reserve, 403rd AW, 2003

14589
U.S. Air Force Reserve, 403rd AW, 2010

Your Minicraft model includes high-quality waterside decals. These decals adhere best to
a glossy surface; and it is recommended that you apply a clear gloss coat over your
painted model.
Use a sharp scissors or knife to cut individual decals from the carrier sheet. Do not cut
into the clear film surrounding the individual decals.
* It is recommended that you apply one decal at a time.
* Place the decal section in warm water, when first inserted in the water your decal will
curl, after approximately ten seconds the decal will uncurl. Remove from water and lay
on a paper towel. After approximately 10 - 20 seconds the decal will slide freely from the
backing paper. Use a small brush to help slide the decal from the backing paper and into
position on the model. Carefully blot excess water from the decal, using care not to move
the decal or tear it.
* If you choose to use a setting solution, apply a thin coat over the decal following the
manufacturer’s instruction.
* Allow the decal to dry overnight. Wash any adhesive residue off the model with a small
amount of clean water and dry thoroughly.
* Apply clear gloss, matte or flat coat to seal decals following the instructions from the
manufacturer.
Visit our Website-
www.minicraftmodels.com
Minicraft Models (US) LLC
1501 Commerce Drive
Elgin, IL 60123
Phone: [phone]