MiniFinder Nano User manual
MiniFinder®Nano
User Manual
English
© 2020 MiniFinder® All rights reserved
Updated: 2020/06/26
User Manual
www.mininder.com 1of 22
nano
minifinder
Thank you for purchasing a MiniFinder®product. We believe you made the right choice. MiniFinder®
Nano is full of smart features that help you monitor, protect and locate your loved ones remotely.
Before you start using your Nano, please read this manual in its entirety.
Thank you!Thank you!
PACKAGE CONTENTSPACKAGE CONTENTS
1. MiniFinder Nano
3. Magnetic Charging Cable
4. Power Adapter
PRODUCT OVERVIEWPRODUCT OVERVIEW
2. GSM LED Light
3. GPS LED Light
1. Panic Button (SOS)
5. Speaker
6. Charging Contact Pins
4. Microphone
7. Heart Rate Sensor
8. On/Off (Call) Button
2. MiniFinder Nano Wristband
3 421
1
4
3
2
5
7
6
8
User Manual
www.mininder.com 2of 22
nano
minifinder
PRODUCT MANAGEMENTPRODUCT MANAGEMENT
A. Please charge your device for 4 hours before using for the rst time.
B. During charging, the blue LED is steady.
C. Blue LED light goes out when fully charged.
D. START the unit by pressing ON/OFF button for 3 seconds.
E. TURN OFF the device by pressing and holding SOS and ON/OFF buttons for 3 seconds.
Speaker
On/Off Button
Charging Pins
Magnetic
charging cable
Place the magnetic charging cable to the charging pins to charge. See the picture below.
On/Off Button
Speaker
User Manual
www.mininder.com 3of 22
nano
minifinder
BLUE LED:
Slow blink =
Searching for GPS signal
1 sec
Steady light =
Charging
Single blink =
Connected to satellite
3 sec
EXPLANATION OF LED LIGHTSEXPLANATION OF LED LIGHTS
Steady light =
No or faulty SIM card
Single blink =
Connected to GSM network
3 sec
Double blink =
Connected to GPRS network
3 sec
Slow blink =
Searching for GSM network
1 sec
GREEN LED:
No light =
Sleep mode or fully charged
User Manual
www.mininder.com 4of 22
nano
minifinder
EXPLANATION OF VOICE NOTIFICATIONSEXPLANATION OF VOICE NOTIFICATIONS
1. “Your mobile alarm is charging”
=
Nano starts charging.
2. “Power on”
=
Nano is on
3. “Power off”
=
Nano is off
4. “Your alarm has been activated”
=
Alarm calls have been answered by the alarm recipient.
5. “Battery is low, please recharge your battery”
=
Nano has low battery level. Voice is repeated 3 times.
6. “Fall alarm has been activated, press the SOS button to stop”
=
Nano has detected a fall. Click the SOS button to cancel the alarm.
7. “Calling contact number 1”
=
When fall alarm is detected, Nano dials authorized number 1. Only if fall alarm is activated.
8. “Calling contact number 2”
=
Nano dials authorized number 2 by pressing & holding the power button for 3 seconds.
DOWNLOAD MINIFINDER GO APPDOWNLOAD MINIFINDER GO APP
To set up and track your MiniFinder®Nano, you need to download MiniFinder GO Tracking System APP.
Download the app by searching the “MiniFinder GO GPS Tracking” in Apple App Store
or Google Play store. Install the app to log in with your created or assigned login details.
If you read the documentation on your mobile phone, please click on the link below to download
the APP.
Apple iPhone: https://apple.co/2P3oYxN Android: http://bit.ly/2IengsS
User Manual
www.mininder.com 5of 22
nano
minifinder
APP OverviewAPP Overview
After logging in the MiniFinder GO APP, you will see the view as shown below.
This consists of 11 different parts:
1. Menu (Device list)
2. Alarm notication
3. Show map
4. Create / Edit GeoFence
5. Applications settings
6. Application info & Help
7. View the position of my mobile phone
8. Zoom in / out
9. View street information of a selected GPS device
10. GPS device location indication on the map
11. Margin of error shown when connecting to WiFi
Menu/Device ListMenu/Device List
Click the menu icon to open the menu. The menu consists of one or more devices (GPSs) depending
on how many licenses you have in the system.
1. Unit name
2. Time for the last position
3. Status icons:
Battery, GPS signal, GSM signal and motion
4. Action menu (history, settings, ...)
User Manual
www.mininder.com 6of 22
nano
minifinder
Device StatusDevice Status
A GPS unit can have three different colors indicating status. Green (Online), Orange (Passive), Red
(Passive) and White (Ofine).
A) Green: The device is online and sending position right now.
B) Orange: The device is passive and has sent last position
more than 10 minutes ago.
C) Red: The device is passive and has sent last position
more than 1 hour ago.
D) White: The device is ofine.
Regardless of the device’s status, you can always press the device row to display the latest
position on the map.
Alarm NoticationAlarm Notication
MiniFinder GO APP supports various types of alarms: Geofence alarm, Fall alarm, SOS / Panic alarm,
Low battery alarm and speeding alarm. All alarms send an alarm notication to the phone’s or tablet’s
screen. Audio alert, vibration and ashing alarm can be activated when opening the APP.
Images below show examples of alarm notications:
- An example of notications on a phone’s screen. - A ashing bell at the top right corner of the app.
- Click on the ashing alarm bell to see active alarms. Click on active alarms to conrm and move
them to the alarm history.
User Manual
www.mininder.com 7of 22
nano
minifinder
HistoryHistory
See positioning history on the map based on date and time.
- Start by clicking Action Menu (1), then click “History” (2).
Action MenuAction Menu
At the far right of the row of units is an Action Menu (three vertical points). In the Action Menu you
can see history (History), call (Call), activate live tracking (Live tracking) and change settings (Setup).
User Manual
www.mininder.com 8of 22
nano
minifinder
- Select a time period and then click “View History” to display the device’s positioning history.
- The following information is displayed for positioning history:
1. A is the start position
2. B is the end position
3. Indicates a particularly selected position
4. The start date and time
5. The end date and time
6. Drag the blue dot to see a particular
position (3) on the map.
User Manual
www.mininder.com 9of 22
nano
minifinder
Call the DeviceCall the Device
To ring your device from your telephone, simply click on Action Menu (1) and then click on “Call” (2)
to start calling.
- When bringing up the sub screen, the detailed statistics are shown, including total distance,
total time and max speed. To clear the selected history, simply click “Clear History”
User Manual
www.mininder.com 10 of 22
nano
minifinder
Rename DeviceRename Device
Edit device name through Device Setting.
Click the Action Menu (1) and then click on the “Setup” (2). Edit device name (3) with your preference.
Then click “Apply” (4) to save the changes.
Live TrackingLive Tracking
Live tracking allows users to track their MiniFinder Nano in real time in a quick and easy way over a short
period of time. By clicking on Action Menu (1) and then Live Tracking (2), the position update intervals
change to 10 seconds for 10 minutes. After that, the tracking returns to the previous selected position
update interval.
User Manual
www.mininder.com 11 of 22
nano
minifinder
Make A CallMake A Call
To make a call, please press and hold the on/off button for 3 seconds. The unit emits an indication,
the green LED starts blinking, and begins dialing to the authorized phone number 2. To end the call
on a telephone, press “1”.
Authorize Telephone NumbersAuthorize Telephone Numbers
To be able to call or receive calls from the device, one or more phone numbers need to be authorized
in the device. Telephone number 1 is used as the rst alarm receiver of the panic alarm (SOS button).
Only phone number 2 receives calls from the call button.
- Enable authorization (3).
- Click on the ag (4) to select a country code.
- Select a country in the list (5).
- Enter a telephone number (6) to receive alarms.
- Click “Apply” to save the settings.
- Open MiniFinder GO APP, click the Action Menu (1) and then click on the “Setup” (2).
3
4
5
6
User Manual
www.mininder.com 12 of 22
nano
minifinder
Low Battery AlarmLow Battery Alarm
If a device’s battery level falls below 10%, you are alerted with an alarm notication and the
battery icon in the menu starts ashing to indicate low battery level.
- To activate Low Battery Alarm, click Action Menu, and select the “Setup”.
- Turn on “Low Battery Alarm” and then click “Apply” to save the settings.
Fall AlarmFall Alarm
An accidental fall can cause devastating consequences. When an accidental fall occurs, the MiniFinder
remote sensor sends an alarm to the APP in the form of an alarm notication on the mobile device’s
screen and an alarm bell in the APP.
- To enable the Fall Alarm, click the Action Menu (1) and then select “Setup” (2).
- Activate “Fall Alarm” (3) and drag the circle to a desired sensitivity (4), then click ”Apply”(5) to save.
“1” indicates the lowest sensitivity, “9” indicates the highest sensitivity.
To end an ongoing fall alarm, press SOS button once.
User Manual
www.mininder.com 13 of 22
nano
minifinder
Alarm via Panic Button (SOS)Alarm via Panic Button (SOS)
Press and hold the panic / SOS button for 3 seconds. There will be a beep sound and the unit’s
green light starts blinking. A SOS message is sent to the MiniFinder GO APP and is displayed as an
alarm notication on the mobile device’s screen.
When the SOS alarm is activated, the unit starts dialing authorized telephone numbers according to
chronological order. If MiniFinder fails to connect the call to the rst phone number, dialing rings the
next authorized phone number.
The dialing cycle is interrupted if the device does not connect to any alarm receiver. The process
resumes after 5 minutes and continues until someone receives the alarm.
To end the call on a telephone, press “1”. If the call is ended by pressing the hang-up button, the
unit’s dialing cycle will continue.
SOSSOS
After SOS function is activated, an alarm notication is sent to the MiniFinder GO APP if the SOS /
panic alarm is activated on the device. The alarm is followed up with telephone calls to authorized
telephone numbers or a local alarm center.
To enable SOS, click the Action Menu and then select “Setup”, and activate “SOS” according to the
image above and click ”Apply” to save the settings.
User Manual
www.mininder.com 14 of 22
nano
minifinder
Speeding AlarmSpeeding Alarm
Click Action Menu (1) of the device that you want to set Speeding Alarm to, and then click “Setup” (2).
Activate ”Speeding Alarm” (1). Drag the circle to a desired speed (2). Finally, click “Apply” (3) to
set the alarm for speeding.
Speaker VolumeSpeaker Volume
Click the action menu in the device list for the device you want to set up the speaker volume, and then
click “Setup”.
Activate the “Speaker volume” (1) and drag the circle on the speaker volume line (2) to a desired
volume. Click “Apply” to save the settings.
User Manual
www.mininder.com 15 of 22
nano
minifinder
Position Update IntervalPosition Update Interval
The device can be tracked by different time interval depending on different requirements. Longer time
interval consumes less battery usage.
To change the update interval, click on the Action Menu and select “Setup”. Then click “Position Update
Interval”, select a desired interval and click “Apply” to save the settings.
Power Saving ModePower Saving Mode
Power Saving Mode is an effective way to optimize battery life. GPS and GSM modules will only be acti-
vated in case of an alarm or event occurs, otherwise, stay deactivated.
Enable Power Save by clicking on the Action Menu and then selecting “Setup”. Turn on “Power save”
and then click “Apply” to save the settings.
User Manual
www.mininder.com 16 of 22
nano
minifinder
Geofence AlarmGeofence Alarm
Geofence is a virtual limited area on the map. When a GPS device leaves a dened area, an alarm
notication, a ringing and an e-mail are sent according to the preferences in the setting.
1) Create a GeoFence
- Start by clicking on the Geofence tab (1) and click “Create” (2) as shown below.
- Then draw an area as a GeoFence on the map.
A) Press once on the map as starting point of the area.
B) Press again to place the second point of the area.
C) Press again to place the third point of the area.
D) Press again to place the forth point of the area.
E) Complete the area by pressing the starting point (point A).
F) Name the area and select which units to connect,
select “Enter” or “Leave” or both to create an alarm.
Then click “Create” to nish the process.
If you are not satised with the location of a point,
click “Back” to delete or hold to delete all and start over.
User Manual
www.mininder.com 17 of 22
nano
minifinder
TooltipTooltip
Infobox (so-called “Tooltip”) contains information of the most recent position.
A) Click the pushpin (or on the device in the menu)
to bring up the properties box.
B) Unit name
C) Location
D) Speed
E) Altitude
F) Battery level
G) Distance between you and the selected device
2) Edit a GeoFence
- Start by clicking on the GeoFence tab (1) as shown below. Then click “Edit” (2).
- In the list, select a GeoFence that you want to edit (3).
- To delete a Geofence, click on the dustbin (4).
- Create/Change a Geofence area’s name (5) in the text eld.
- Click on “Edit area” (6) to edit the area’s size or location.
- Select “Enter”(7) or “Leave”(8) or both to create an alarm
- Select (9) the units to be affected by the area.
- Finish editing by clicking “Save”.
To disable a geofence without removing it, deselect all units when edit.
User Manual
www.mininder.com 18 of 22
nano
minifinder
Tag Function (Mark Places)Tag Function (Mark Places)
On the map in the MiniFinder GO APP, you can mark places with particular information.
- Long press on the place where you want to mark on the map. (1)
- You can give a name (2), a description (3), an icon (4) on the map and even attach an image (5).
- Press “Create” (6) to save.
- Press the icon on the map (1) to edit the marked place and save the changes (2) or delete (3).
1
1
User Manual
www.mininder.com 19 of 22
nano
minifinder
APP SettingsAPP Settings
- Click on the gear symbol to make settings in the MiniFinder GO APP.
- Settings Menu.
1. Number of licenses and your username.
2. Change your password.
3. Map selector (Classic, Hybrid, Terrain and Satellite)
4. “Keep Screen Alive” keeps your mobile device’s screen
on until it is turned off manually. The setting may
involve increased battery usage for your mobile device
depending on settings.
5. “Tooltip” shows information of your
GPS above the map pin. Disable this if you do not wish
to view the information.
6. Alarm settings denes what your mobile device would
react when alarms are triggered.
7. Enter an email address to receive emails notication
when alarm are triggered.
8. Change a language:
English, Swedish, German, Finnish, French.
9. Simply quit the settings to apply changes.
9
Other manuals for Nano
1
Table of contents
