Minka Group minkaAire VOLTERRA F702L-VB Guide

INSTRUCTION MANUAL WARRANTY CERTIFICATE
© 2002 Minka Lighting, Inc.
VOLTERRA
BY

©2019 Minka Lighting Inc. Manual design and all elements of manual design are protected by United States Federal and/or State Law including
Patents, Trademark, and/or Copyright Laws.

The Minka-Aire® warranty is for one (1) year from the date of purchase from an authorized Minka-Aire® dealer.
This warranty is only valid to the original purchaser or user against all defects in material and workmanship (light bulbs
excluded) for one (1) full year. Additionally, Minka-Aire® warrants the motor only for the lifetime of the Minka Aire ceiling
fan (excluding wall controls and electrical components), to the original purchaser or user.
* The warranty is voided with the use of any non- Minka-Aire®electrical devices, E.g., wall controls or electrical dimmer switches, etc…
* The warranty is void once the original purchaser or user ceases to own the fan or the fan is moved from its original point of installation.
* The warranty is void with the use of any hanger bracket (non-Minka Aire or non-fan specific) other than the hanger bracket supplied & installed
with this specific fan.

Date Purchased Store Purchased Model Number Serial Number
F702L
Warranty Service Information
To obtain warranty service during the warranty period, the purchaser should return the fan with the sales receipt to the original place of
purchase. The authorized Minka-Aire® dealer, at its sole discretion, will either repair or replace the fan after verifying the legitimacy of the warranty
claim. Replacement is subject to availability of the same model. If the model is unavailable it will be replaced by one of equal value. This is a
limited warranty; the original purchaser or user is responsible for the cost of removal and reinstallation of repaired or replacement product.
To obtain the name of the Minka-Aire® authorized dealer nearest you call the Minka-Aire® customer care department at 1-800-307-3267, or
contact Minka-Aire® through www.minkagroup.net and select FAQ to answer any questions or if you require additional assistance submit the
question form found there.

CONTENTS
SAFETY RULES....................................................................................
PACKAGE CONTENTS.....................................................................
INSTALLING THE FAN.....................................................................
ASSEMBLING THE FAN..................................................................
HANGING THE FAN.........................................................................
ELECTRICAL CONNECTIONS.......................................................
INSTALLING THE WALL TRANSMITTER.................................
FINISHING THE INSTALLATION.......................................................
BLADE INSTALLATION..........................................................................
INSTALLING THE LIGHT BULBS & GLASS SHADE...................
OPERATING YOUR WALL TRANSMITTER...................................
CARE OF YOUR FAN..............................................................................
TROUBLESHOOTING............................................................................
SPECIFICATIONS.....................................................................................
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1151 W. Bradford Court, Corona, CA 92882 For Customer Assistance Call: 1-800-307-3267
UL
LISTED
E75795
R

SAFETY RULES
1
1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box.
2. Be cautious! Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams.
3. Make sure that all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a
do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.
4. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the
floor and 18 inches from the tip of the blades to the wall.
5. If you are mounting the fan to a ceiling fan outlet box, use a U.L. Listed metal octagonal outlet box marked "Acceptable for Fan Support". Secure the
box directly to the building structure. The outlet box and its support must be able to support the moving weight of the fan (at least 50 pounds) Do
not use a plastic box.
6. Caution: To reduce the risk of injury use only the screws provided with the outlet box in conjunction with the lock washers provided with the fan.
7. If you are mounting the fan to a joist, make sure it is able to support the moving weight of the fan (at least 50 pounds).
8. After you install the fan, make sure that all mounting components are secured to prevent the fan from falling.
9. Do not insert anything into the fan blades while the fan is operating.
10. Turn the fan off and wait for the blades to stop completely before changing the fan direction.

WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY, MOUNT FAN ONLY TO A U.L. LISTED OUTLET BOX OR SUPPORTING SYSTEM MARKED
ACCEPTABLE FOR FAN SUPPORT AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX IN CONJUCTION WITH THE LOCK WASHERS PROVIDED WITH THE
FAN. MOST OUTLET BOXES COMMONLY USED FOR FAN SUPPORT OF LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND NEED TO BE REPLACED.
CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT.
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE HOLDERS WHILE INSTALLING, BALANCING THE BLADES OR CLEANING THE FAN. DO NOT
INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.
TO REDUCE THE RISK OF FIRE OR ELECTRONIC SHOCK, THIS FAN ONLY CAN USE MK668-90W0406A LED ONLY SOLID-STATE SPEED CONTROL WITH WCS213 WALL
CONTROL ONLY.
NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may
occur. It must be understood that common sense, caution and care are factors which can not be built into this product. These factors must be
supplied by the person (s) installing, caring for and operating the unit.
NOTE: READ AND SAVE ALL INSTRUCTIONS!

2
PACKAGE CONTENTS
Unpack your fan and check the contents. You should have the following items:
A
B
C
13
15
16
17
14a
14b
3
1
2
4
5
9
10
11
12
6
7
8
Fan blades (5 )
Hanger bracket
Canopy
Canopy cover
Downrod assembly
Coupling cover
Upper housing
Bulb holder assembly
Fan motor/housing assembly
Blade holders (5)
E11 4W LED bulbs (2)
Glass shade
Light kit stem
Wall Transmitter Incl. 2 Mounting
Screws and 3 Wire Nuts
Wall Plate w/2 Mounting screws
Receiver with 7 wire nuts
Extra Wall Plate w/2 Mounting screws
Balancing kit
Mounting Hardware:
#10 x 1.5" Wood Screws (2 PCs.)
#8 x 3/4" Machine screws (2 PCs.)
Lock washers (2 PCs.)
4mm Star washers (2 PCs.)
Wire nuts (3 PCs.), Washers (2 PCs.)
Blade Attachment Hardware:
3/16" x 7.5 mm Screws (16 PCs.)
Fibber Washers (16 PCs.)
Bracket Holder Hardware:
3/16" x 3/4" Screws with lock washers
(11 PCs.)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14a.
14b.
15.
16.
17.
A.
B.
C.

3
Tools Required: Phillips screw driver; slotted screw driver; step-ladder; wire cutters; electrical tape.
INSTALLING THE FAN
MOUNTING OPTIONS
If there isn't an existing mounting box, then read the following instructions. Disconnect the
power by removing fuses or turning off circuit breakers.
Secure the outlet box directly to the building structure. Use appropriate fasteners and building
materials. The outlet box and its support must be able to fully support the moving weight of
the fan (at least 50 lbs.). Use a UL Listed metal outlet box. Do not use a plastic outlet box.
Figure 1, 2 and 3 are examples of different ways to mount the outlet box.
Note:You may need a longer downrod to maintain proper blade clearance when installing on a
steep, sloped ceiling. Longer downrods are available from your Minka-Aire®dealer.
To hang your fan where there is an existing fixture but no ceiling joist, you may need to install
a hanger bar as shown in Fig. 4 (available at your Minka-Aire®dealer).
FIG. 1
FIG. 3
FIG. 2
FIG. 4
CROSS BRACE
CEILING
JOIST
CEILING
JOIST
CEILING
JOIST
OUTLET BOX
PARALLEL WOOD BRACE
(Min. 2" Thick)
OUTLET
BOX
OUTLET BOX
CEILING JOIST OR
CROSS BRACE
ANGLED CEILING
MAXIMUM 18 ANGLE PROVIDE
STRONG
SUPPORT
RECESSED
OUTLET BOX
HANGER
OPENING
MUST BE
FACING
UPSIDE
HANGER BAR
(OPTIONAL)
HANGER
BRACKET

4
Your fan is packed with the motor and Upper Housing unassembled, proceed
the following steps for fan assembly:
Step1. Remove the two screws and rubber washers from the top of the motor
center band. Place the upper housing over the motor center band and secure it
with the two screws and rubber washers previously removed. (Fig.5)
Step2. Engage the white wire connectors from the motor and the bulb holder
assembly make sure the connection is secured Follow the same procedure for the
orange and black wire connectors.(Fig.6)
Step3. Loosen the three screws (do not remove) from the motor coupling.(Fig. 7)
Step4. Place the bulb holder assembly key holes over the 3 screws previously
loosened from the motor coupling, turn the bulb holder assembly until it locks in
place at the narrow section of the key holes. secure by tightening the three
screws previously loosened.(Fig.7)
ASSEMBLING THE FAN
Fig. 5 Fig. 6
Fig. 7
TOP MOTOR
MOTOR
CENTER
BAND
SCREW
UPPER
HOUSING
RUBBER
WASHERS
MOTOR
WIRE
CONNECTORS
BULB HOLDER
ASSEMBLY

5
WARNING: All of the parts, hardware and components such as the
hanger bracket and hanger ball have been provided for your safety and
the proper installation of your new ceiling fan. The use of other parts,
hardware or components not supplied by Minka Aire®with the fan will
void the Minka Aire®Warranty.
REMEMBER to turn off the power. Follow the steps below to hang your
fan properly:
Step 1. Secure the hanger bracket to the ceiling outlet box using screws
included with your outlet box, lock washers included with the fan. (Fig.8)
Step 2. Loosen the two set screws and remove the hitch pin and lock pin
in the top coupling of the motor assembly. (Fig. 9)
Step 3. Remove hanger ball from downrod assembly by loosening set
screw, removing the cross pin, and sliding ball off rod. (Fig.10)
Step 4. Carefully feed fan wires up through the downrod. (Fig. 11)
Thread the rod into the coupling, next line up holes and replace lock
pin and hitch pin. Tighten set screws.
Step 5. Slip coupling cover, canopy cover and canopy onto downrod.
(Fig. 12) Carefully reinstall hanger ball onto rod being sure that cross
pin is in correct position, set screws are tighten and wires are not
twisted.
Step 6. Now lift motor assembly into position and place hanger ball
into hanger bracket. Rotate until the check groove has dropped into
the registration slot and seats firmly. (Fig. 13) Rod should not rotate if
this is done correctly.
HANGING THE FAN

Fig. 9 Fig.10 Fig. 11 Fig. 13
OUTLET BOX
HANGER BRACKET
Fig. 8
Coupling cover

6
WARNING: To avoid possible electrical shock be sure electricity is
turned off at the main fuse or breaker box before wiring.
NOTE: The Aire Control® System is equipped with a learning frequency
function which has 256 code combinations to prevent potential
interference from other remote units. The frequency on your Receiver
and Transmitter units have been preset at the factory. (Fig. 14) No
frequency change is necessary, should you desire to install another fan
within the same home or area with a seperate frequency code please
see the "frequency interference" troubleshooting section of this
instruction manual to learn how to change the frequency.
Step 1. Insert Receiver into Hanger Bracket with the flat side of the
Receiver facing the ceiling. (Fig. 15)
Step 2. Motor to Receiver Electrical Connections: Connect the
WHITE wire from the fan to the WHITE wire marked "TO MOTOR N"
from the Receiver. Connect the BLACK wire from the fan to the BLACK
wire marked "TO MOTOR L" from the Receiver. Connect the BLUE wire
from the fan to the BLUE wire marked "For Light" from the Receiver.
NOTE: If your ceiling fan features an UP Light: Connect the ORANGE wire
from the fan to the ORANGE wire marked "For Up Light" from the
Receiver. Otherwise disregard this step and proceed to secure all wire
connections with the plastic wire nuts provided. (Fig. 16 & 17)
Note: Fan must be installed at a maximum distance of 40 feet from the
transmitting unit for proper signal transmission between the
transmitting unit and the fan's receiving unit.
ELECTRICAL CONNECTIONS

Step 3. Receiver to House Supply Wires Electrical Connections:
Connect the WHITE wire (Neutral) from the outlet box to the WHITE
wire marked "AC in N" from the receiver. Connect the BLACK wire
(Hot) from the outlet box to the BLACK wire marked "AC in L" from
the receiver. Secure all wire connections with the plastic wire nuts
provided. (Fig. 16 & 17)
Step 4. If your outlet box has a GROUND wire (Green or Bare Copper)
connect this wire to the Hanger Ball and Hanger Bracket Ground
wires. If your outlet box does not have a Ground Wire, then connect
the Hanger Ball and Hanger Bracket Ground Wires together. Secure
wire connection with the plastic wire nut provided. (Fig. 16 & 17)
After all splices are made, check to make sure there are no loose
strands. As an additional precaution we suggest to secure the plastic
wire connectors to the wires with electrical tape.
Fig. 15
RECEIVER
HANGER BRACKET
Fig. 14

7
Fig. 18
WARNING! HOOK UP "IN SERIES" ONLY. DO NOT CONNECT NEUTRAL SUPPLY WIRE OF
ELECTRIC CIRCUIT TO THE TRANSMITTER WALL SWITCH, DAMAGE TO THE
TRANSMITTER WALL SWITCH AND POSSIBLE FIRE COULD OCCUR.
Step 1. Remove the existing wall plate and switch from the wall outlet box.
Step 2. Make the electrical connections as shown in Fig.17. If your outlet box has a ground
wire (Green or Bare Copper) connect the Transmitter's ground wire directly to one of the
screws from the outlet box . Secure all wire connections with the plastic wire nuts
provided.
Step 3. Carefully tuck the wire connections inside the outlet box. Use the screws provided
to secure the wall transmitter and wall plate to the outlet box. (Fig. 18)
NOTE: Your WC220 Aire ControlTM System includes two sets of face and decorative
plate color options. The wall control comes with standard white faceplate attached. If you
desire to replace it with the Ivory color faceplate included, use a small flat screw driver
and gently pry it apart from the top or bottom of the plate.
INSTALLING THE WALL TRANSMITTER

8
Step 1. Remove 1 of the 2 screws from the bottom of the hanger bracket and loosen the other
one half a turn from the screw head.
Step 2. Slide the canopy up towards the hanger bracket and place the key hole on the canopy
over the screw on the hanger bracket, turn canopy until it locks in place at the narrow section
of the key holes. (Fig. 19)
Step 3. Align the circular hole on canopy with the remaining hole on the hanger bracket,
secure by tightening the two set screws.
Note: Adjust the canopy screws as necessary until the canopy and canopy cover are snug.
FINISHING THE INSTALLATION
Fig. 19
OUTLET BOX
HANGER
BRACKET
HANGER
BALL
CANOPY
CANOPY
COVER

9
Fig 21
THE FOLLOWING OPERATION MUST BE ACCOMPLISHED
BEFORE INSTALLING THE LIGHT KIT.
Step1. Attach the fan blade to the blade holder using the
screws and fiber washers provided. Tighten screws
securely. Repeat process for remaining blades. (Fig. 20)
Step2. Rotate motor until holes become visible through
the light plate access window. Align the holes from the
blade holder to the holes from the motor and secure in
place with screws provided. (Fig. 21)
BLADE INSTALLATION
BLADE
HOLDER
BLADE
HOLDER
SCREW
ACCESS
WINDOW
LIGHT PLATE

10
Fig. 22
INSTALLING THE LIGHT BULBS & GLASS SHADE
BULB
SOCKET
GLASS SHADE
LIGHT PLATE
LIGHT KIT STEM
4W
LED
BULBS
WARNING: Shut of the power supply before removing or replacing lamp. In handling of LED
bulb, care should be taken not to touch it with your bare hands. Oil residue will shorten the life
of the LED bulb. If you accidentally come into contact, wipe thoroughly with a clean, lint-free,
cotton cloth. Allow the bulb to cool off for 10 minutes before changing the bulb. Use light bulb
in accordance with the fan's specification. TO REDUCE THE RISK OF FIRE DO NOT EXCEED
MAXIMUM WATTAGE RATING.
Step 1. Install 2x4W LED bulbs by screwing it clockwise into bulb sockets. (Fig. 22)
Step 2. Raise the glass shade up against the light plate and secure it to the fan with the light kit
stem. (Fig. 22)

11
OPERATING THE REMOTE CONTROL/WALL CONTROL
Restore Power to Ceiling Fan.
A. Buttons:
These buttons are used to set the fan speeds as
follows;
= Low Speed
= Medium Speed
= High Speed
B. Button:
This button turns the fan off.
C. Button:
These buttons turn the light ON or OFF and also
control the brightness settings of the light. The
following.
instructions apply to ceiling fans that feature a
DOWN light ( button) only or ceiling fans that
feature an UP light ( button) and a DOWN
light ( button) that are controlled independent
of each other;
Press and release the button for the desired
light to turn the light ON or OFF. Press and hold
the button to set the desired light brightness.
The light will cycle between bright and dim
settings as long as the button is pressed. The
light key has an automatic auto-resume feature
that allows the light to remain at the same
brightness as the last time it was turned off.
D. OFF-ON Slide Button (Wall Control Fans
Only)
This button turns the power Off and On to the
Fan and Light(s).
E. Button: (Full Function Remote Control
Units Only)
This button is used to change the direction of
the rotation of the blades; forward for warm
weather or reverse for cool weather.
NOTE: If your Remote Control or Wall Control
does not have a " " button, Please look for a
slide reverse switch on the motor housing.
Remote Control only: Install a A23 12 volt battery (included). To prevent damage to transmitter remove the battery if not used for long periods of time.