Minolta SC-100 User manual

INTRODUCTION
1
Thank you for purchasing the Minolta Slide Feeder SC-100.
The Slide Feeder SC-100 is designed for use with the Minolta Dimâge Scan Multi
scanner and allows you to automatically feed and continuously scan up to 50
mounted slides at one time.The Slide Feeder can be used with either the
Dimâge Scan Multi utility software, TWAIN driver, or plug-in and allows you to
select the file destination.
Before using the Slide Feeder, please read this instruction manual thoroughly. It
is also necessary to read the Accessory Information section in the scanner’s
software instruction manual.

FOR PROPER AND SAFE USE
2
To avoid fire or electric shock:
• Do not expose this unit to liquids.
• Do not insert metal objects into this unit.
•Do not attempt to disassemble this product. Take the
product to a Minolta Service facility for repairs.
If there is smoke, a strange smell, or any other unusual
conditions, shut down and unplug the unit, then contact a Minolta
Service Facility.
CAUTION
Unexpected damage may occur if this unit is left unattended near
young children.
Please read and understand each caution before using this product.

TABLE OF CONTENTS
3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..1
For Proper and Safe Use . . . . . . . . . . . . . . . . . . . ..2
Names of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . ..4
Attaching the Slide Feeder. . . . . . . . . . . . . . . . . . ..6
Recommended Slide Mounts . . . . . . . . . . . . . . . . 10
Loading Slides. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Detaching the Slide Feeder . . . . . . . . . . . . . . . . . 14
Removing Jammed Slides . . . . . . . . . . . . . . . . . . 18
Care and Handling. . . . . . . . . . . . . . . . . . . . . . . . 26
Indicator Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Technical Details . . . . . . . . . . . . . . . . . . . . . . . . . 28

NAMES OF PARTS
4
Slide-feeder cover
“IN” column
“OUT” column
Mount cover
Pressure bar
Indicator lamp
Power switch
Inside the Mount Cover
Transport Unit
Spring

5
Holding screw
Contacts
Holding screw
Holding screw
Slide carrier

ATTACHING THE SLIDE FEEDER
6
1. Remove the connector
cover from the top of
the scanner.
2. Press the power
switch to turn the
scanner on.
• Set-up will begin.
• The green indicator
lamp blinks slowly
while the scanner is
busy setting-up.Wait
until the lamp turns
off.

7Continued on next page.
3. Insert the slide carrier
into the film-slot in
the direction
indicated by the white
arrow on top of the
carrier.
• Do not insert the slide
carrier at an angle.
• The slide carrier is
included in the slide-
feeder package.
4. Gently push the
carrier into the
scanner until the
insertion mark is
aligned with the film-
slot door.
• The slide carrier will
be automatically
guided in past the
mark.

ATTACHING THE SLIDE FEEDER – CONT’D
8
5. Shut down the
computer, then turn
the scanner off.
• Always be sure the
scanner is off when
attaching and
detaching the slide
feeder.
6. Attach the slide feeder
to the scanner by
lining up the
scanner’s connector
with the contacts on
the slide feeder.
• Push the slide feeder
straight down so the
contacts are fully
inserted into the
connector.The two
pegs on either side of
the slide feeder’s
contacts should fit into
the notches on the
scanner.

9
7. Tighten the holding
screws on both sides
of the slide feeder,
then tighten the
holding screw on the
top of the scanner.
• Tighten the holding
screws by pressing
and turning.
8. Press the power
switch on the front of
the slide feeder to
turn the scanner on.
• Set-up will begin.
• The indicator lamp on
the front of the slide
feeder will blink slowly
while the scanner is
setting up. Wait until
the indicator lamp on
the front of the slide
feeder glows.
9. Turn on the computer.

RECOMMENDED SLIDE MOUNTS
10
Some slide mounts are not recommended for use in the slide feeder. Jamming is
likely to occur with the following slide mounts.
The Slide Feeder can load
approximately 50 mounted slides
(1.6mm thickness).The number of slides
that can be loaded depends on the
thickness of the slide mounts. Slide
mounts should be between 1 – 3mm
thick and have a flat, even surface on
both the top and bottom.
Mounts with indentations on the surface,
such as for labels or slots where film is
to be inserted.
Mounts with rounded edges.
Mounts with rough, uneven edges or
surfaces.
Max. thickness: 3mm
Remount slides if the mount is damaged or coming apart.