Minolta DIMAGE SCAN MULTI PRO User manual

HARDWARE MANUAL
9222-2887-11 P-A208
E

BEFORE YOU BEGIN
2
This manual may not be copied in part or whole without prior
written permission from Minolta. Every necessary precaution
has been taken to ensure the accuracy of this instruction man-
ual. Minolta is not responsible for any loss or damage caused
from the operation of this product.
Thank you for purchasing this Minolta product. Please take the time to read through this instruc-
tion manual so you can enjoy all the features of your new scanner.
This manual contains information regarding products introduced before September, 2002. To
obtain compatibility information for products released after this date, contact a Minolta Service
Facility (www.minoltasupport.com).This product is designed to work with accessories manufac-
tured and distributed by Minolta. Using accessories or equipment not endorsed by Minolta may
result in unsatisfactory performance or damage to the product and its accessories.
Check the packing list before using this product. If any items are missing, immediately contact
your dealer.
AC power cord
(Shape of plug varies
with destination)
Scanner unit Slide Mount Holder
SH-P1 35mm Film Holder
FH-P1
Universal Holder
UH-P1
Standard Attachment HA-P1
Glassless Attachment HA-P2
Film Mask Set FM-P1
SCSI cable SC-P1 IEEE 1394 cable FC-P1
DiMAGE Scan Utility CD-ROM,
DiMAGE Instruction Manuals-CD-ROM
Quick Reference Guide
and Minolta International
Warranty Certificate

3
FOR PROPER AND SAFE USE
Read and understand all warnings and cautions before using this product.
WARNING
•Use only within the voltage range specified on the unit. Inappropriate current may cause
damage or injury through fire or electric shock.
•Do not disassemble this product. Electric shock may cause injury if a high-voltage circuit inside
the product is touched. Take the product to a Minolta Service Facility when repairs are required.
•Immediately unplug the unit and discontinue use if the product is dropped or subjected to an
impact in which the interior is exposed. The continued use of a damaged product may cause
injuries or fire.
•Store this product out of reach of children. Be careful when around children not to harm them
with the product or parts.
•Do not operate this product or handle the power cord with wet hands. Do not place a container
with liquid near the product. If liquid comes in contact with the product, immediately unplug the
unit. The continued use of a product exposed to a liquid may cause damage or injury through
fire or electric shock.
•Do not insert hands, inflammable objects, or metal objects such as paper clips or staples into
this product. It may cause damage or injury through fire or electric shock. Discontinue use if an
object enters the product.
•Do not use the product near inflammable gases or liquids such as gasoline, benzine, or paint
thinner. Do not use inflammable products such as alcohol, benzine, or paint thinner to clean the
product. The use of inflammable cleaners and solvents may cause an explosion or fire.
•When unplugging the unit, do not pull on the power cord. Hold the plug when removing the cord
from an outlet.
•Do not damage, twist, modify, heat, or place heavy objects on the power cord. A damaged cord
may cause damage or injury through fire or electric shock.
•If the product emits a strange odor, heat, or smoke, discontinue use. Immediately unplug the
product. The continued use of a damaged product or part may cause injuries or fire.
•Take the product to a Minolta Service Facility when repairs are required.
•This product should only be operated in the upright position. Inappropriate placement may result
in fire.
•Damage or injury through fire or electric shock may result if the product is used or stored in the
following conditions:
In humid or dusty environments
In direct sunlight or hot environments
In smoky or oily areas
In unventilated areas
On unstable or unlevel surfaces
•Insert the plug securely into the electrical outlet.
•Do not use if the cord is damaged.
•Do not connect the ground to a gas pipe, telephone ground, or water pipe. Improper grounding
can result in injury from electric shock.
•Unplug the product when cleaning or when the unit is not in use for long periods.
•Periodically check that the power cord is not damaged and the plug is clean. Dust and dirt that
may collect between the prongs of the plugs may result in fire.
CAUTION

TABLE OF CONTENTS
4
System requirements......................................................................................................5
Names of parts ..............................................................................................................6
Scanner setup ................................................................................................................7
Removing the optics locking screw ....................................................................7
Transporting the scanner ........................................................................7
Before connecting the scanner to the computer ................................................7
Connecting the SCSI cable ................................................................................8
Connecting the IEEE 1394 (FireWire) cable ......................................................9
Auto Power Save ................................................................................................9
Loading the film holders ..............................................................................................10
Handling film......................................................................................................10
Where is the emulsion? ....................................................................................10
Loading 35mm film strips ..................................................................................10
Loading 35mm mounted slides ........................................................................10
Inserting attachments into the Universal holder................................................11
Using the standard attachment ........................................................................12
Using the glassless attachment ........................................................................12
Multi-format Set HS-P1 (sold separately)..........................................................13
Loading a film holder into the scanner..............................................................15
Ejecting a film holder ........................................................................................15
Scanner notes ..............................................................................................................16
Easy Scan Utility ..............................................................................................16
About the DiMAGE Scan Utility ........................................................................16
Film format and type settings............................................................................16
Disconnecting the scanner................................................................................16
SCSI cable ............................................................................................16
IEEE 1394 (FireWire) cable ..................................................................16
Digital ICE3system requirements......................................................................18
Scanner resolution ............................................................................................19
Scanner color profiles ......................................................................................19
Job file lists ..............................................................................................................20
35mm ..............................................................................................................20
6 X 4.5 ..............................................................................................................21
6 X 6 ..............................................................................................................22
6 X 7 ..............................................................................................................23
6 X 8 ..............................................................................................................24
6 X 9 and Multi-format 6 X 9 ............................................................................25
Multi-format 35mm ............................................................................................25
Troubleshooting ............................................................................................................26
Checking software installation - Windows ........................................................27
Technical support ..............................................................................................28
Warranty and product registration ....................................................................28
Image data sheet..........................................................................................................29
Technical specifications ................................................................................................30
This manual contains information specific to this model scanner. This includes hardware setup
and use as well as notes about software operation for this model scanner. See the supplied
DiMAGE Scan Utility software manual for information on the installation and operation of the scan-
ner software.

5
SYSTEM REQUIREMENTS
SCSI: Pentium 166MHz or later processor.
IEEE 1394: Pentium II or later processor.
A Pentium III processor is recommended when
scanning with 16-bit color depth. For Digital ICE3
requirements, see page18.
A minimum of 96 MB of RAM (Windows (128MB with Windows XP)) or 64 MB of RAM (Macintosh) in addi-
tion to the requirements for the operating system and applications is required. 256 MB or more is necessary
when scanning with 16-bit color depth; 512 MB or more is recommended.
For Digital ICE3requirements, see page18.
A High Color (16bit) 640 x 480 pixel monitor is
required.
1024 x 768 pixels is recommended.
TWAIN driver compatible with Photoshop 4.0.1,
5.0.2, 5.5, 6.0, and 7.0, and PhotoshopLE 5.0.
Recommended SCSI boards: Adaptec SCSI Card
19160, Adaptec SCSI Card 29160, Adaptec SCSI
Card 29160N.
Recommended IEEE boards: Adaptec Fireconnect
4300, PROCOMP SpeedDemon 400P. Standard
OHCI compatible non-DV-dedicated IEEE 1394
ports guarantied by the computer manufacturer can
be used.
PC / AT compatible computers
Operation is not guarantied for custom or home-built machines.
The scanner cannot be used with notebook computers.
SCSI: preinstalled Windows 98, 98 Second Edition,
Me, 2000 Professional, NT 4.0, XP.
IEEE 1394: preinstalled Windows Me, 2000
Professional, XP.
Mac OS 8.6* to 9.2.2, and
OS 10.1.3 to 10.1.5.
A 640 x 480 pixel monitor capable of displaying
32,000 colors is required.
1024 x 768 pixels is recommended.
SCSI: PowerPC 604 or later
FireWire: PowerPC G3 or later.
PowerPC G4 processor is recommended when
scanning with 16-bit color depth. For Digital ICE3
requirements, see page18.
Plug-in compatible with Photoshop 5.0.2, 5.5, 6.0,
and 7.0, and PhotoshopLE 5.0.
2 GB or more of available hard disk space is required. 6 GB or more of available hard disk space is neces-
sary when scanning with 16-bit color depth; 8 GB or more is recommended.
For Digital ICE3requirements, see page18.
Macintosh
Recommended SCSI boards: Adaptec
PowerDomain 29160N, PowerDomain 2930U,
PowerDomain 2940UW, or PowerDomain
2940U2W.**
Only the standard built-in IEEE interface supplied
by Apple Computer, Inc.
* To use preinstalled Mac OS 8.6 with a built-in FireWire port, a Firewire 2.2 to 2.3.3 extension
must be installed. This software can be downloaded free of charge from the apple web site at
http://www.apple.com.
**Boards must be guarantied by the manufacturer to work with the computer and operating sys-
tem.
The computer and the operating system must be guarantied by the manufacturer to support IEEE
1394 (FireWire), or SCSI interface.
Check the Minolta web site for the latest compatibility information:
Europe: http://www.minoltasupport.com
North America: http://www.minoltausa.com.

NAMES OF PARTS
6
Slide Mount Holder (p. 10)
35mm Film Holder (p. 10)
Universal Holder (p. 11)
Film attachments
Film masks
Front door
Indicator lamp
Power switch
Eject button
SCSI ID switch
IEEE 1394 (FireWire) ports
Dip switch
AC terminal
SCSI ports

7
SCANNER SETUP
Transporting the scanner
To prevent damage when transporting the scanner, the
optics locking screw must be used. Before inserting the
screw in the lock position, the scanner must be initial-
ized with the DiMAGE Scan Utility.
With the scanner connected to the
computer and the DiMAGE Scan
Utility running, press the control
(Windows) or command (Macintosh)
key plus the shift and L keys simulta-
neously. A window indicating the
command will be displayed; click the
OK button to move the optics to the lock position.
A message stating the completion of the operation will be displayed; click the OK button. Turn off
the computer and scanner. Disconnect the cable and power cord from the scanner and screw the
optic locking screw in the lock position.
Removing the optics locking screw
Before the scanner can be used, the optics locking screw on the bottom panel of the scanner
must be removed with a flat-head screwdriver.The locking screw is necessary to transport the
scanner. Place the screw in the storage position toward the front of the scanner body for future
use.
Before connecting the scanner to a computer
Before connecting the scanner to a computer, the the DiMAGE Scan Utility must first be installed.
Read the software instruction manual for the installation procedure.
The scanner should be placed on a level surface free from vibrations. It should be located away
from direct sunlight and in a clean, dry, well-ventilated area.

SCANNER SETUP
8
Connecting the SCSI cable
The scanner is supplied with an ultra SCSI D-sub half-pitch 50-pin cable. Contact your dealer if a
different cable is required.
The computer and all peripheral devices must be off
before connecting the scanner.
The terminator dip switch on the back of the
scanner eliminates the need for an external ter-
minator. If the scanner is to be the only SCSI
device connected to the computer or it is the last
device in a daisy chain, switch number 1 should
be in the on position; terminating the SCSI chain
helps to suppress noise, not terminating a chain
can cause slowdowns, data errors, and crashes.
If the scanner is to be connected somewhere
within a daisy chain, switch 1 should be in the
off position. The initial setting for all the switches
is on. Dip switch 4 must be in the on position to
use a SCSI interface.
Connect the scanner to the computer or SCSI
chain with the cable. Either SCSI port can be
used for the connection.
Plug the power cord into the back of the unit.
The other end of the power cord should be
plugged into a grounded outlet.
Set the SCSI ID for the scanner by pressing the buttons above and
below the ID number window. Devices in the same chain must have
unique ID numbers. Depending on the computer system, some SCSI
IDs may already be assigned:
IBM PC/AT 7 - SCSI host adapter
Macintosh 0 - internal hard drive
3 - internal CD-ROM drive
7 - operating system
IDE Macintosh systems do not use SCSI ID 0 for the hard drive. SCSI
ID 3 is available on the external bus on Macintosh systems with a
dual bus.

9
Connecting the IEEE1394 (FireWire) cable
The scanner is supplied with an IEEE 1394 (FireWire) cable. Up to 63 devices can be attached to
a computer using this interface. However, the number of devices is limited to 16 when using a
daisy-chain configuration.
The computer and all peripheral devices must be off
before connecting the scanner.
Set dip switch number 4 to the off position to
active the IEEE ports. Switch 4 must be
moved to the on position if a SCSI cable is
used.
Connect the scanner to the computer or
IEEE peripheral chain with the cable. Either
IEEE port can be used for the connection.
Plug the power cord into the back of the unit.
The other end of the power cord should be
plugged into a grounded outlet.
Auto Power Save
The scanner automatically turns the scan-
ning light source off during long periods of
inactivity to save energy and preserve the life
of the fluorescent tube. Though not recom-
mended, the auto-power-save function can
be disabled by setting dip switch number 2 to
the off position.

LOADING THE FILM HOLDERS
10
Loading 35mm mounted slides
The Slide Mount Holder SH-P1 is for mounted 35mm film.
Up to four slide can be placed in the holder. Slide mounts
must be between 1mm and 2mm thick to fit the holder.
Glass mounts cannot be used; the glass refracts the light
resulting in distorted and unevenly illuminated scans.
With the cover hinges away from you, open the holder by
lifting on the latch on the cover.
Handling film
To achieve the best possible reproduction from the scanner, the film and film holder should be
free from dust and dirt. Always work with processed film in a clean, dust-free environment. Handle
film by the edges or mount to prevent fingerprints and dirt marring the image area. Special lint
free gloves are available from photographic equipment retailers for film handling as well as anti-
static cloths, brushes, and blowers for removing dust. Film cleaner can be used to remove oil,
grease, or dirt from film; carefully follow the manufacturer's instructions and precautions for the
film cleaning solvent.
Loading 35mm film strips
The 35mm Film Holder FH-P1 is for unmounted 35mm
film. Film strips up to six frames in length can be placed
in the holder.
With the cover hinges away from you, open the holder by
lifting on the latch on the cover.
With the emulsion down, place the film sideways
into the holder and under the retaining tabs (1).
Align the film frames with the holder windows.
Carefully close the cover until the latch clicks. See
page 15 for instructions on how to load the holder
into the scanner.
1
Where is the emulsion?
When film is scanned, the emulsion side of the film should be down. When viewing the film image,
if the image is orientated correctly rather than a mirror image, the emulsion side is facing down. If
the image is abstract or symmetrical so its orientation is difficult to determine, the emulsion is
down if the frame numbers and edge markings can be read correctly. With mounted slides, the
emulsion is on the same side of the mount as the film manufacturer's or processor’s name is
printed.

11
With the emulsion down, place the slide mounts
sideways into the holder. The mount must be
oriented as illustrated otherwise the top and
bottom of the image will be cropped.
Carefully close the cover until the latch clicks.
See page 15 for instructions on how to load the
holder into the scanner.
When the slide mount holder is in the scanner, the
last slide can be removed and a new slide inserted
without ejecting the holder. A prescan should be
made each time a slide is inserted when using the
scanner’s autofocus and auto exposure functions,
see the DiMAGE Scan Utility manual.
Inserting attachments into the Universal Holder
The Universal Holder is used for scanning medium format film. All standard formats from 6X4.5 to
6X9 can be scanned. Two attachments with and without glass are supplied with the holder. An
attachment must be inserted to hold the film.
With the hinge to the top, slide the left side of
the attachment into the holder so the two pro-
trusions on the attachment are aligned to the
two slots in the Universal Holder.
Carefully press the right side of the attach-
ment down until the latch in the Universal
Holder clicks.
To remove an attachment, slide the latch (1)
and lift the attachment from the front right cor-
ner.
1

Using the glassless attachment
The glassless attachment allows scans without any
extra glass surfaces in the optical path. See page
11 for instructions on how to insert the attachment
into the Universal Holder.
LOADING THE FILM HOLDERS
12
Using the standard attachment
The standard attachment is equipped with glass to hold the film flat. A set of five masks are pro-
vided for standard formats: 6X4.5, 6X6, 6X7, 6X8, and 6X9. See page 11 for instructions on how
to insert the attachment into the Universal Holder.
To open, press the latch on the attach-
ment and lift the cover.
Slide the tabs of the appropriate mask
into the corresponding slots on each side
of the attachment hinge. Fit the holes on
the other side of the mask (1) over the
registration pins (2) on the base of the
attachment. Always use a mask when
scanning or newton rings and flare may
degrade the image quality.
With the emulsion down, place the film on the mask.
Align the frame with the mask aperture.
Carefully close the cover until the latch clicks. See
page 15 for instructions on how to load the holder
into the scanner.
To open, press the latch on the attach-
ment and lift the cover.
Adjust the masking bars on the attach-
ment to the film format. White markings
indicate the format positions: 6X4.5, 6X6,
6X7, 6X8, and 6X9.
12

13
Multi-format Set HS-P1 (sold separately)
The multi-format attachment allows non-standard
film sizes to be scanned. The set includes the
multi-format attachment cover (1), the multi-format
attachment base (2), and a set of three masks
(FM-P2)(3).
With the emulsion down, place the film on the
attachment. Align the frame with the attachment
aperture.
Carefully close the cover until the latch clicks. See
page 15 for instructions on how to load the holder
into the scanner.
1
2
3
Slide the left side of the attachment base into
the Universal Holder so the two protrusions on
the attachment are aligned to the two slots in
the holder.
Carefully press the right side of the base down
until the latch in the Universal Holder clicks.
Insert the two pin on the attachment cover into
the two corresponding holes in the Universal
Holder. Both pins should click into place.
The Multi-format attachment is designed for non-standard film sizes, special technical films, and
non-photographic transparent media. The maximum area that can be scanned at one time is
56.58 mm X 83.82 mm. This attachment can be used for 16 mm film, microfilm, or 24 X 65 mm
panoramic images. TEM (transmission electron microscopy) film can also be scanned. However,
since the image area of some TEM films is larger than the holder aperture, several scans need to
be made and then the image must be reconstructed digitally.

LOADING THE FILM HOLDERS
14
With a straight edge and sharp knife, cut the aperture for
the film from one of the masks. The aperture should be
the same dimensions as the image area, not the film size;
the mask should separate the film from the glass base of
the attachment to prevent newton rings, and the aperture
should only show the image area to eliminate flare from
the surrounding clear film.
Slide the tab of the mask into the slot
on the side of the Universal Holder.
Fit the holes on the other side of the
mask (2) over the registration pins on
the base of the the holder on each
side of the cover hinges.
With the emulsion down, place the film on the
mask. Align the image area with the mask aper-
ture.
Carefully close the cover until the latch clicks. See
page 15 for instructions on how to load the holder
into the scanner.
1
To remove the film, slide the latch toward the
center of the holder and lift the cover.
4To remove the glass base of the attachment, slide
the latch on the Universal Holder (4) and lift the
base from the holder.
To remove the multi-format attachment from the
Universal Holder, slide the latch near the hinge (3)
to remove the cover.
3
2

15
Ejecting a film holder
Use the eject button on the scanner body or in
the DiMAGE Scan Utility window to remove the
holder; the scanner automatically ejects the
holder to its initial insertion position. Do not
touch or hinder the holder while it is moving.
When the indicator lamp goes out, remove the
holder from the scanner.
Do not insert the film holder into the scanner while
the DiMAGE Scan Utility is launching or the scan-
ner is initializing (the indicator lamp blinks during
this period).
Loading a film holder into the scanner
Before using the scanner, install the DiMAGE Scan Utility; see the software instruction manual.
Tu rn on the scanner and then start the computer. Launch the DiMAGE Scan Utility before insert-
ing the film holder.
Insert the film holder into the scanner in the direction
indicated by the white arrow. Hold the holder straight
and level when inserting it into the scanner.
Carefully push the holder into the
scanner until the arrow mark (1) is
aligned with the scanner door; the
holder will be automatically fed into
the scanner from that point. Never
touch or hinder the holder while it is
moving.
1
Eject
button

SCANNER NOTES
16
Film format and type settings
When scanning, the film type and format as well as the holder type must be selected in the main
window of the DiMAGE Scan Utility. See scanner setup in the basic-scanning section of the soft-
ware manual.
When using the Slide Mount Holder SH-P1 or the 35 mm Film Holder FH-P1, select the 35 mm
option from the film-format drop-down menu. When scanning medium-format film with the stan-
dard or glassless attachment in the universal holder,
select the appropriate format from the drop-down
menu: 6 X 4.5, 6 X 6, 6 X 7, 6 X 8, or 6 X 9. When
using the optional Multi-format attachment HS-P1, two
menu options are available depending on the film
used: Multi Format 35mm and Multi Format 6X9. The
type of holder must also be specified between glass
and glassless from the holder-type drop-down menu
when the Universal Holder is used.
Film type can be selected between color and black
and white, positive and negative film. Film for prints is
negative film. Slide film is positive film. The transpar-
ent-media option is for use with the optional Multi-format attachment when scanning specialized
film or non-photographic originals such as microfilm or microscope slides. Also for the Multi-format
attachment, the TEM film option is for transmission electron microscopy film.
Disconnecting the scanner
SCSI cable
The scanner and computer must be turned off before the SCSI cable can be disconnected. If the
scanner is connected to a SCSI chain, all the devices in the chain must be turned off before dis-
connecting the cable.
IEEE 1394 (FireWire) cable
The easiest and safest way to disconnect the scanner from the computer is to turn both devices
off as well as any peripheral devices and remove the cable. However, the following procedures
can be used depending on the operating system employed.
Easy Scan Utility
The Easy Scan Utility software is a simple scanning interface designed for individuals with no
image processing or DTP experience. This software is not compatible with this scanner. The
DiMAGE Scan Utility’s custom wizard can be used to automate the scanning workflow, see the
software instruction manual.
About the DiMAGE Scan Utility
Prescan size can be selected in the preferences dialog box with this scanner model. See setting
scanner preferences in the advanced scanning section of the DiMAGE Scan Utility manual.

17
Quit the DiMAGE Scan Utility. Confirm that the scanner indicator lamp is not blinking. Turn the
scanner off and then disconnect the cable.
Windows 98, 98SE, 2000 professional, XP, and Macintosh
Windows Me
To disconnect the scanner, quit the DiMAGE Scan Utility. Left click on the unplug-or-
eject-hardware icon located on the task bar. A small window will open indicating the
device to be stopped.
Click on the small window to stop the
device. The safe-to-remove-hardware
window will appear. Click OK. Turn the
scanner off and then disconnect the
cable.
When more than one external device are connected to
the computer, repeat the procedure above except right
click on the unplug-or-eject-hardware icon. This will open
the unplug-or-eject-hardware window after clicking on the
small window indicating the unplug operation.
On the unplug-or-eject-hardware window, the hardware
devices to be stopped will be displayed. Highlight the
device by clicking on it then click the stop button.
A confirmation screen will open to indi-
cate the device to be stopped. Click the
OK button to stop the device.
A third and final screen will appear to
indicate the scanner can be safely dis-
connected from the computer; click OK.
Turn the scanner off and then disconnect
the cable.

SCANNER NOTES
18
Digital ICE3system requirements
Digital ICE3is a collection of powerful image-processing tools. To make use of the Digital ROC
and GEM functions, the following system requirements must be met:
Format
Interface
35 mm
Multi-format 35 mm
6 X 9
SCSI
IEEE 1394
Color
depth
8 bit
Minimum system requirements
CPU
Pentium 166MHz or later
RAM
128MB
Hard disk space
1.2GB
35 mm
Multi-format 35 mm
6 X 9
35 mm
Multi-format 35 mm
6 X 9
35 mm
Multi-format 35 mm
6 X 9
16 bit
8 bit
16 bit
Pentium II or later
256MB
128MB
256MB
PC/AT compatible computers
2GB
4GB
2GB
3GB
6GB
1.2GB
2GB
4GB
2GB
3GB
6GB
Recommended system requirements
35 mm
Multi-format 35 mm
6 X 9
SCSI
or
IEEE 1394
8 bit
Pentium III or later
2GB
35 mm
Multi-format 35 mm
6 X 9
16 bit
512MB
4GB
6GB
3GB
4GB
8GB
Macintosh computers
When determining the RAM available for a Macintosh computer, the volume required for the oper-
ating system and any application in use must be subtracted from the total memory allocation of
the computer.
35 mm
Multi-format 35 mm
6 X 9
SCSI
or
FireWire
8 bit PowerPC 604 or later
(SCSI)
PowerPC G3 or later
(FireWire)
96MB1.2GB
35 mm
Multi-format 35 mm
6 X 9
16 bit
192MB
2GB
4GB
2GB
3GB
6GB
Recommended system requirements
35 mm
Multi-format 35 mm
6 X 9
8 bit
PowerPC G4 or later
2GB
35 mm
Multi-format 35 mm
6 X 9
16 bit 512MB
4GB
6GB
3GB
4GB
8GB
256MB
384MB

19
Scanner color profiles
When the DiMAGE Scan Utility is installed, the scanner profiles listed below are automatically
installed for this model scanner. These profiles have been included for advanced color matching
with profile-to-profile conversions in sophisticated image-processing or DTP applications. When
using these profiles, the color reproduced may not be the same as the color matching system in
the utility software.
MLTF5000.icc - used with positive film at any color depth other than 16-bit linear.
MLTF5000p.icc - used with positive film with 16-bit linear color depth.
The profiles are located in the following locations:
Scanner resolution
The maximum resolution of this scanner is 4800 X 4800 dpi. The maximum optical resolution
varies with the format of the film: 35 mm film - 4800 X 4800, medium-format film - 3200 X 4800.
Scans of medium-format film can have a final resolution of 4800 X 4800 dpi through interpolation.
The minimum resolution is 300 dpi for 35mm and 200 dpi for medium-format film.
System32 Drivers
System
Mac OS (8, 9)
ColorSync profile
MLTF5000.icc
MLTF5000p.icc
Mac OS X
Users (User logon
name)
Library ColorSync Profiles
WINNT
Windows (2000)
Spool Color
System32 DriversWindows
Windows (XP)
Spool Color
Windows (98, 98SE, Me)
Windows System Color

JOB FILE LISTS
20
Category Job name Input res. Output res. Mag. Unit Lock (input) Output size Lock (output)
WH WH W H
4800 37.08 25.02 7008 4728
1.460 0.985
Default Default 1200 300 400 pixel 1752 1182 OFF 1752 1182 OFF 1752 1182
ColorLaserPrinter A4Full 4800 600 800 mm 35.38 25.02 OFF 283 200.152 ON 6685 4728
A4Half 3550 600 591 mm 35.53 25.04 OFF 210 148 ON 4960 3496
A4Quarter 2518 600 419 mm 35.32 25.06 OFF 148 105 ON 3496 2480
LetterFull 4800 600 800 inch 1.26 0.99 OFF 10.1 7.88 ON 6060 4728
LetterHalf 3494 600 582 inch 1.46 0.94 OFF 8.5 5.45 ON 5100 3270
LetterQuarter 2589 600 431 inch 1.26 0.99 OFF 5.45 4.25 ON 3270 2550
Photosensitive A3Full 4749 400 1187 mm 35.38 25.02 OFF 420 297 ON 6614 4677
A4Full 3358 400 839 mm 35.4 25.03 OFF 297 210 ON 4677 3307
A5Full 2366 400 591 mm 35.53 25.04 OFF 210 148 ON 3307 2330
LetterFull 3452 400 863 inch 1.26 0.99 OFF 10.9 8.5 ON 4360 3400
LetterHalf 2329 400 582 inch 1.46 0.94 OFF 8.5 5.45 ON 3400 2180
LetterQuarter 1726 400 431 inch 1.26 0.99 OFF 5.45 4.25 ON 2180 1700
8x10 3249 400 812 inch 1.23 0.99 OFF 10 8 ON 4000 3200
11x14 4460 400 1115 mm 31.93 25.02 OFF 356 279 ON 5606 4393
10x12 4061 400 1015 mm 30.05 25.02 OFF 305 254 ON 4803 4000
2L 2031 400 507 mm 35.11 25.05 OFF 178 127 ON 2803 2000
PostCard4x6 1644 400 411 inch 1.46 0.97 OFF 6 4 ON 2400 1600
Ink-Jet & SuperB 3945 300 1315 mm 36.73 25.02 OFF 483 329 ON 5704 3885
Dye-SubPrinter A3Full 3561 300 1187 mm 35.38 25.02 OFF 420 297 ON 4960 3507
A4Full 2518 300 839 mm 35.4 25.03 OFF 297 210 ON 3507 2480
A4Half 1775 300 591 mm 35.53 25.04 OFF 210 148 ON 2480 1748
A4Quarter 1259 300 419 mm 35.32 25.06 OFF 148 105 ON 1748 1240
LetterFull 2589 300 863 inch 1.26 0.99 OFF 10.9 8.5 ON 3270 2550
LetterHalf 1747 300 582 inch 1.46 0.94 OFF 8.5 5.45 ON 2550 1635
LetterQuarter 1295 300 431 inch 1.26 0.99 OFF 5.45 4.25 ON 1635 1275
Photo4x6 1214 300 404 mm 37.13 24.75 OFF 150 100 ON 1771 1181
Photo3x5 1068 300 356 mm 35.67 25 OFF 127 89 ON 1500 1051
WebPage 1240x836 850 72 1180 pixel 1240 836 OFF 1240 836 ON 1240 836
1112x750 762 72 1058 pixel 1112 750 OFF 1112 750 ON 1112 750
984x663 674 72 936 pixel 984 663 OFF 984 663 ON 984 663
792x534 543 72 754 pixel 792 534 OFF 792 534 ON 792 534
760x512 521 72 723 pixel 760 512 OFF 760 512 ON 760 512
600x404 411 72 570 pixel 600 404 OFF 600 404 ON 600 404
320x240 300 72 416 pixel 320 240 OFF 320 240 ON 320 240
PhotoCD PhotoCD2048x3072 2105 300 701 pixel 3072 2048 OFF 3072 2048 ON 3072 2048
PhotoCD1024x1536 1053 300 351 pixel 1536 1024 OFF 1536 1024 ON 1536 1024
PhotoCD512x768 527 300 175 pixel 768 512 OFF 768 512 ON 768 512
Screen 1920x1200 1316 72 1827 pixel 1920 1200 OFF 1920 1200 ON 1920 1200
1600x1200 1219 72 1693 pixel 1600 1200 OFF 1600 1200 ON 1600 1200
1280x1024 1040 72 1444 pixel 1280 1024 OFF 1280 1024 ON 1280 1024
1280x960 975 72 1354 pixel 1280 960 OFF 1280 960 ON 1280 960
1152x870 884 72 1227 pixel 1152 870 OFF 1152 870 ON 1152 870
1024x768 780 72 1083 pixel 1024 768 OFF 1024 768 ON 1024 768
832x624 837 72 1162 pixel 832 824 OFF 832 824 ON 832 824
800x600 610 72 847 pixel 800 600 OFF 800 600 ON 800 600
640x480 488 72 677 pixel 640 480 OFF 640 480 ON 640 480
Document A4Half 426 72 591 mm 35.53 25.04 OFF 210 148 ON 595 419
A4Quarter 302 72 419 mm 35.32 25.06 OFF 148 105 ON 419 297
A4Eighth 300 72 416 mm 25.24 17.79 OFF 105 74 ON 297 209
LetterHalf 420 72 583 inch 1.46 0.93 OFF 8.5 5.45 ON 612 392
LetterQuarter 311 72 431 inch 1.26 0.99 OFF 5.45 4.25 ON 392 306
LetterEighth 300 72 416 inch 1.02 0.65 OFF 4.25 2.72 ON 306 195
FilmRecorder 4K 2806 2400 116 pixel 4096 2731 OFF 4096 2731 ON 4096 2731
2K 1403 2400 58 pixel 2048 1365 OFF 2048 1365 ON 2048 1365
Input size Input pixels
35mm
Jobs can be used to make scan settings based on the final use of the image. See making-the-
final-scan section in the DiMAGE Scan Utility manual. The following charts list the parameters of
the scanner’s Job files: