MiraBox HSV373 User manual

HDMI Over IP Extender
HDMI CAT5/CAT5e/6 Extender 120m
Model #:HSV373

In ca p a b le o f u sa g e d u e to d a m a g e d p a cka g e
P le a se co n ta ct w ith u s
if yo u h ave proble m s b e lo w .
D o n o t kn o w h o w to u se
O th e r p ro b le m s
Congratulations for owning a MiraBox product.
Our products
aim to meet all your connectivity needs wherever
you go.
Have fun with our products!
Please read this manual carefully before first use.
https://www.amazon.com/s?marketplaceID=ATVP
DKIKX0DER&me=A3IK7HWRZCAKOB&merchant=A
3IK7HWRZCAKOB&redirect=true
E-mail:[e-mail]
Skype:jack.hotspot

Introduction
This product not only can work as other normal
HDMI extender by CAT5/5e/6 cable up to 120
meters, but also can transmit HDMI data over local
network. The data could be transmitted over
switch, router and other ethernet device, and
extend the transfer distance to over 20km.
It also could work in broadcast mode, like HDMI
splitter, broadcast HDMI signal from one sender to
multiple receivers.
Specifications
Output Signal
HDMI
Protocol
M-JPEG
Resolution
Up to 1080p
Transmission Distance
Up to 120m (394ft)
Network Cable
CAT5/5e/6
HDMI Cable
Up to 2m (Input & Output)
Power Supply
DC 5V/1A

Package Contents
•HDMI CAT5/5e/6 Extender - 120m (TX & RX)
•2x Power adapters
•User's guide
Layout
●HDMI In: Connect your HDMI source here with
an HDMI cable (cable not included)
Rj45
HDMI TX
Reset
Power Jack
HDMI In

●Power Jack: Connect the included 5V DC power
adapter here
●Reset: Press to reset if HDMI Extender doesn't
work properly
●RJ45: Link to the Receiver's RJ45 via a Cat5/5e/6
cable
●HDMI Out: Connect to your HDMI display
here with an HDMI cable (cable not
included)
Rj45
HDMI RX
Reset
Power Jack
HDMI Out

●Reset: Press to reset if HDMI Extender
doesn't work properly
Hardware Installation
Note: To achieve optimal performance, a
CAT6 cable is recommended.
1. Power off all devices including your HDMI
source and display.
2. Connect your HDMI source to the
Transmitter's HDMI IN connector.
3. Connect your HDMI display to the
Receiver's HDMI OUT connector with an
HDMI cable (not included).
4. Connect and link the Transmitter and
Receiver by a CAT5/5e/6 cable.
5. Plug the included power adapters into
the Transmitter'sand Receiver's Power Jacks,
then plug both power adapters into reliable
power outlets.

HDMI Source HDMI Extender
Sender
HDMI Extender
Receiver
Cat5e/6 Cable
HDMI IN HDMI OUT
Xbox One
Monitor
HDMI IN
Cat5e/6 Cable
Cat5e/6Cable
Cat5e/6 Cable
HDMI OUT
HDMI OUT
HDMI OUT
Cat5e/6 Cable
HDMI Extender
Sender
HDMI Extender
Receiver
HDMI Extender
Receiver
HDMI Extender
Receiver
HDMI Media player
Monitor
Monitor
Monitor
6. Power on your HDMI device and HDMI
display.
7. The HDMI Extender is ready for use.
Application
1. Single output: Extend HDMI signals up to
120 meters over one CAT5/5e/6 cable.
2. Multiple outputs: Extend and split using
network router/switch.
- One Extender (TX) to several Receivers(RX)

HDMI IN
Cat5e/6Cable
Cat5e/6 Cable
HDMI Extender
Sender
HDMI Media player
Cat5e/6Cable
Cat5e/6 Cable
HDMI Extender
Receiver
HDMI OUT
HDMI Extender
Receiver
HDMI OUT
HDMI Extender
Receiver
HDMI OUT
HDMI Extender
Receiver
HDMI OUT
... ... ...
MonitorMonitorMonitorMonitor
3.Cascade: Unlimited extension with
network router/repeater.
FAQ & Solutions
Q: The TV displays "Waiting for
connection..." on the bottom-right corner:
A: 1) Check whether the power adapter of
Transmitter (TX),Receiver (RX) or Network
Switch (if used) is connected.
2) Make sure the Network cable (CAT5/5e/6) is
firmly connected between TX and RX.
Q: The TV displays "Searching TX ":

A: 1) Make sure the HDMI device is connected
to the Transmitter (TX).
2) Use other HDMI cables to connect.
3) If still doesn't work, connect the HDMI
device to the TV directly to see if there's a
signal.
Q: The HDMI extender isn't working
properly:
A: 1) Please check the cable lengths are within
below:
- HDMI cables: 2m
- Network cable (CAT5/5e/6): 120m
2) Press the "Reset" button on the TX/RX and
reconnect.

Thank you for choosing MiraBox