Miranda picoLink Series Instruction Manual

SDM-171p
Video DAC
Guide to Installation
and Operation
M144-9900-202
Copyright 2007
Miranda Technologies Inc.
Specifications may be subject to change.
Printed in Canada
March 2007
SDM-171p
picoLink Series
Miranda
Technologies inc.
3499 Douglas-B.-Floreani
St-Laurent, Québec, Canada H4S 1Y6
Tel. [phone]
Fax. [phone]
www.miranda.com

Guide to Installation and Operation
SDM-171p
Radio Frequency Interference and Immunity
This unit generates, uses, and can radiate radio
frequency energy. If the unit is not properly installed and
used in accordance with this guide, it may cause
interference with radio communications. Operation with
non-certified peripheral devices is likely to result in
interference with radio and television reception. This
equipment has been tested and complies with the limits
in accordance with the specifications in:
FCC Part 15, Subpart B
CE EN50081-1:1992
CE EN50082-1:1992.
CONTACT MIRANDA
For technical assistance, please contact the Miranda
Technical Support centre nearest you:
Americas
Telephone:
[phone]
e-mail:
[email protected]
Asia
Telephone:
[phone]
e-mail:
[email protected]
Europe, Middle East, Africa, UK
Telephone:
[phone]
e-mail:
[email protected]
France (only)
Telephone:
[phone]
e-mail:
[email protected]
Visit our web site at
www.miranda.com

Guide to Installation and Operation
SDM-171p
CONTENTS
page
1.0 SDM-171p.............................................. 1
1.1 Introduction....................................................1
1.2 Features........................................................1
2.0 Physical Layout.....................................2
3.0 Installation.............................................3
3.1 Power Supply................................................3
3.2 4:2:2 Input ...................................................4
3.3 CAV Outputs .................................................4
4.0 Operation...............................................5
4.1 Switch Settings..............................................5
4.2 Status LED....................................................6
5.0 Specifications........................................7

Guide to Installation and Operation
SDM-171p

Guide to Installation and Operation
SDM-171p | 1
1.0 SDM-171p
1.1 Introduction
The SDM-171p is the industry’s smallest 4:2:2 serial
digital video to component analog video DAC. This
product automatically detects 525-line and 625-line 4:2:2
signals conforming to the SMPTE 259M-C standard and
provides BETA/EBU or GBR output signals. An internal
test pattern generator provides a color bars test signal
for both BETA/EBU and GBR outputs. In addition, this
feature-packed unit delivers ease-of-use, a simplified
design, easy installation and operation.
Figure 1: SDM-171p functional block diagram
1.2 Features
•Automatic 525-line and 625-line format input
detection
•Output standard selection: BETA/EBU or GBR with or
without setup
•Color bars generator
•Bi-color LED showing error status on input 4:2:2
signal
•Very small packaging with aluminum extruded body
Serial to
parallel DAC4:2:2 IN B/B-Y
G/Y
R/R-Y
COMPONENT OUT

Guide to Installation and Operation
2| SDM-171p
2.0 Physical Layout
Figure 2 illustrates the SDM-171p’s major parts and their
locations. The video source is connected to the 4:2:2
input BNC and the component analog output signals are
provided by the CAV outputs. Error status is provided by
the status LED and mode settings are configured by two
3-position slide switches. Finally, the power source is
connected to the power connector.
.
Figure 2: Physical layout of the SDM-171p
4:2:2 input
Power connector
CAV outputs
Status LED
3-position slide switches

Guide to Installation and Operation
SDM-171p | 3
3.0 Installation
3.1 Power Supply
The power supplies LKS-WSA and LKS-WSE, for 110 V
and 220 V operation respectively, are used to power the
SDM-171p. Each power supply provides a regulated +5
VDC@750 mA power source. The SDM-171p employs a
mini XLR-3 connector for its power needs. Figure 3
provides a detailed pinout of the male connector.
13
2
(male connector-facing)
Pin 1: Shield
Pin 2: GND
Pin 3: +5 VDC
Figure 3: Power connector pinout

Guide to Installation and Operation
4| SDM-171p
3.2 4:2:2 Input
Connect a 4:2:2 serial digital signal to the BNC labeled
4:2:2 IN. The 4:2:2 input signal must conform to the
SMPTE 259M-C standard.
3.3 CAV Outputs
The CAV outputs consist of green, blue, and red color
coded male BNC connectors. Male connectors are
provided so as to connect the SDM-171p directly to
monitoring equipment. Available CAV output standards
are:
•BETA/EBU
BETA/EBU operation provides Y/B-Y/R-Y
signals on the green, blue, and red BNCs
respectively (BETA = 60Hz; EBU = 50Hz.).
•GBR
The GBR format can be with or without setup.
Refer to Section 4.0 Operation in order to select the
desired output CAV standard.

Guide to Installation and Operation
SDM-171p | 5
4.0 Operation
4.1 Switch Settings
Figure 4 shows the slide switch locations and functions.
Figure 4: SDM-171p switch settings
Output CAV standard switch (SW1)
BETA: For BETA/EBU CAV outputs, set SW1 to
this position.
•BETA: 60 Hz with setup
•EBU: 50 HZ, no setup
The Y/B-Y/R-Y outputs are provided by the
green, blue, and red connectors
respectively.
GBR 7.5: With 525-line inputs, set SW1 to this
position for GBR outputs with 7.5 IRE setup.
There is no setup for 625-line GBR outputs.
GBR: For GBR outputs with 0 IRE setup, set SW1
to this position.
Normal and test pattern switch (SW2)
Normal: For normal operation, set SW2 to this
position.
BETA GBR 7.5 GBR Normal Test
SDM-171p
Miranda Technologies inc.
Made in Canada
Output CAV standard (SW1)
Normal and test (SW2)

Guide to Installation and Operation
6| SDM-171p
Test: Set SW2 to Test in order to enable the test
pattern generator. Make sure a valid 4:2:2
input signal is installed. 525-line outputs
produce a 75% color bars signal whereas
625-line outputs produce a 75% color bars
with 100% white bar signal.
4.2 Status LED
The bi-colored status LED, located next to the CAV
output cable, is provided to identify any input errors and
the selection of the test pattern. The following lists all
possible situations.
Green: Indicates the SDM-171p is powered and has
detected a valid 4:2:2 serial digital signal.
Red: Indicates an error with the input signal has
been detected or simply, there is no input
signal installed.
Yellow: The test pattern is selected.
If an input signal error is detected during a test
pattern selection, the status LED will remain red.