Miranda SDM-771p Instruction Manual

SDM-771P/75/110
i
Radio Frequency Interference and Immunity
This unit generates, uses, and can radiate radio frequency energy. If the unit
is not properly installed and used in accordance with this guide, it may cause
interference with radio communications. Operation with non-certified periph-
eral devices is likely to result in interference with radio and television recep-
tion. This equipment has been tested and complies with the limits in accor-
dance with the specifications in:
-FCC Part 15, Subpart B
-CE EN50081-1:1992
-CE EN50082-1:1992.
How to contact us:
For technical assistance, please contact the Miranda Technical Support cen-
tre nearest you:
Americas Asia
Telephone: Telephone:
[phone] [phone]
e-mail: e-mail:
[email protected] [email protected]
Europe, Middle East, Africa, UK France (only)
Telephone: Telephone:
[phone] [phone]
e-mail: e-mail:
[email protected] [email protected]
Visit our web site at www.miranda.com

Guide to Installation and Operation
ii
Contents
page
1 SDM-771p AES/EBU Digital to Analog Converter....1
1.1 Introduction...............................................................1
1.2 Features....................................................................1
2 Overall View................................................................... 2
3 Installation......................................................................4
3.1 Power Supply............................................................4
3.2 AES Input................................................................. 4
3.3 Analog Output...........................................................5
4 Operation........................................................................ 6
4.1 Configuring the Switches..........................................6
4.2 Indicating the Status of the AES-EBU Carrier.......... 6
5 Specifications................................................................8

Guide to Installation and Operation
1
1 SDM-771p AES/EBU Digital to Analog Converter
1.1 Introduction
This picoLink module is a 24-bit digital-to-audio converter.
It converts AES/EBU or SP-Dif signals into analog stereo signals.
It has three output levels to optimize the dynamics of the analog
circuit.
A de-emphasis stage in 50/15 µs (48 or 44.1 kHz) format accu
-
rately restores the signal when it has been emphasized.
This module is available in two versions, depending on the stan
-
dard selected:
SDM-771p/110: symmetric AES3 110 Ω / XLR input
SDM-771p/75: asymmetric AES3-id 75 Ω
or SP-Dif / BNC input
Figure 1 Functional Block Diagram
1.2 Features
-AES3 110 Ωor AES3-id 75 Ωinput
-Stereo analog output
-Adjustable output level
-De-emphasis: 50-15 µs

2 Overall view
The figures below represents the SDM-771P/75 and the SDM-
771P/110. The input is connected to the BNC socket over 75 Ω
and to a three-point XLR connector over 110 Ω.
A multicolor LED indicates the status of the AES-EBU carrier. A
mini DE-EMPH switch is used to configure the de-emphasis cir-
cuit. The output level can be adjusted using the two mini LEFT
and RIGHT three-position switches.
Power is provided via the power connector
Figure 2.1 SDM-771p, 75 ΩVersion
SDM-771P/75/110
2

Guide to Installation and Operation
3
Figure 2.2 SDM-771p, 110 ΩVersion

SDM-771P/75/110
4
3 Installation
3.1 Power Supply
The power supplies LKS-WSA and LKS-WSE, for 110V and 220V
operation respectively, are used to power the SDM-771p/75/110.
Each power supply provides a regulated +5VDC@750mA power
source. Plug the power supply into a wall or power bar outlet.
The SDM-771p uses a mini XLR-3 connector for its power needs;
figure 3.1 provides a detailed pinout of the male connector.
Figure 3.1 Power connector pinout
3.2 AES Input
SDM-771p/75:
BNC socket: Connect an asymmetricAES 75 Ωsignal to an AES
IN BNC connector. This signal must comply with the AES3-id or
SPDif standard.
SDM-771p/110:
Three-point female XLR connector: Connect a symmetric AES-
110 Ωsignal to an AES IN connector (refer to figure 3.2 for con-
nector pinout). This signal must comply with the AES3 standard
(professional or consumer).
+5VDC
GND
Shield

Guide to Installation and Operation
5
Figure 3.2 Female XLR connector pinout
3.3 Analog Output
SDM-771p/75 & SDM-771p/110:
Refer to the Configuration section to set the signal output level
and the de-emphasis type.
Figure 3.3 Male XLR connector pinout
GND
Signal _
Signal +
Signal +
Signal _
GND

SDM-771P/75/110
6
4 Operation
4.1 Configuring the switches
Figure 5 Switch Location
Level Switches
The level of each stereo output can be set using the two three-
position LEFT & RIGHT switches
+24 0 dBFS = +24 dBu
+22 0 dBFS = +22 dBu
+20 0 dBFS = +20 dBu
De-emphasis Switch
De-emphasis (50-15 µs) is available for signals sampled at fre-
quencies of 44.1k or 48k. The three-position DE-EMPH switch
can be used to select the customized mode of operation. This
selection is valid for both channels.
4.2 Indicating Status of the AES-EBU Carrier
A multicolored LED, located beside the output cord, indicates the
status of the carrier by changing color.
Configuring the left output level
Configuring the right output level
Configuring de-emphasis
Position