MistKing HT-24 User manual

Go to
MistKing
.com for more information on systems and parts
Mistking
®
is a Registered Trade Mark of © All Rights Reserved
Controller is ON and connected MistKing® system is misting
Controller is OFF and idle
Current time clock
Low relative humidity alarm
System is in day mode
System is in night mode
LCD Display
Hygrostat - Thermometer Timer Connection
1.
Connect the BLUE lead on the hygrostat controller to the
power adapter of your MistKing misting system.
2.
Connect the BLACK lead to your pump and ZipDrip (if
available). DO NOT plug ZipDrip to blue lead.
REMEMBER
REMEMBER to keep the humidity sensor away from direct
mist or it will become waterlogged and read humidity at
99.9% for several days until it dries. If this happens, use a
hair dryer to dry the sensor. Be careful not to burn it.
NOTE: Hygrostat controller works only with
MistKing systems and therefore requires
additional Mistking components to work
properly.
Using the hygrostat with non-MistKing
equipment voids warranty.
MistKing® Hygrostat Controller (HT-24), with humidity probe, is able to precisely monitor the humidity and maintain specified levels
based on programmed requirements. Different settings can be set for day and night.
Model: HT-24
Hygrostat Controller

Go to
MistKing
.com for more information on systems and parts
Mistking
®
is a Registered Trade Mark of © All Rights Reserved
MENU ITEM
DAY SET
NIGHT SET
DIFFERENCE
ALARM
CLOCK
Description
Day humidity setting
Night humidity setting
Variance from day/night humidity setting before pump will engage to mist
Duration of OFF cycle during the day
Low humidity alarm
C
Current Time
Settings Range
1-99%
1-99%
1-20%
1-70%
00:00 - 23:59
Tips:
a) RAPID ADJUST: While setting individual values, press and hold “up arrow” or “down arrow” for faster advancement of settings
b) SAVE & EXIT: When done modifying values press and hold “SET” key for 3 seconds to Save & Exit. Alternatively don't input anything
for 15 seconds and controller will exit automatically saving and displaying the main screen.
Switch between “
o
C and
o
F”: In normal status, pressing up and down arrow key together for 5 seconds switches temperature between
“
o
C and
o
F”.
Q
Quick-ON Function: In normal status, press and hold up arrow key for 5 seconds to active the quick-on function. While pressed the
controller will activate allowing you to quickly bypass any congured settings and manually activate the misting system. Quick ON, does
not affect any settings. When up arrow is released, controller resumes normal operation and misting stops.
Energy-Saving: If there is no key activity on the HT-24 for approximately 10 minutes the LCD backlight automatically turns off. Pressing
any key will reactivate the back light again.
Setup Instructions:
1. Set Current Time (picture A):
Press “ O ” key once to set the clock: When in setup, press “ O ” key to switch between
hour and minute; press up arrow or down arrow to adjust the values when ashing.
2. Configure Humidity settings (picture B):
In normal status, press and hold “SET” for 3 seconds to enter into the setting mode.
a.
a. In the setting mode, “DAY SET” ashes, use up arrow or down arrow to set
required humidity for the day.
b. Press “SET” key once to switch to “NIGHT SET”. When ashing, use up arrow or
down arrow to modify the humidity value for the night.
c. Press “SET” key once to switch to “DIFFERENCE”. When “DIFFERENCE” ashes,
press up arrow or down arrow key to adjust the value. Difference refers to the
allowed humidify drop before the pump will engage.
d
d. Press “SET” key once to switch to “ALARM”. When “ALARM” ashes, use up
arrow or down arrow key to set the ALARM value.
e. Press “SET” key once to save and exit the setting mode.
LL