Mitone MITSP65 User manual

STEREO TWIN BLUETOOTH SPEAKER
USER MANUAL
Please read the manual carefully before use
and keep it well for further use
i
MODEL: Mitone MITSP65
Package Contents
-Rechargeable Portable Speaker 2 Pcs
-3.5mm audio cable
-Micro USB Charging cable
-User guide
Product Description
FRONT VIEW
1: Aux In-put Jack
2: Function Indicates LED
3: Micro USB Charge Jack
4: Power ON/OFF
5: Volume-/Previous Sound
6: MicroPhone
7: Volume+/Next Sound
8: Handfree/Play/Pause Button
Pairing The Speakers For Stereo Use
1. Slide the power switch at the back of both speakers to on. Both speaker
will give a beeping sound. The blue LED light will flash quickly.
2. Press the button on top of both speakers and keep pressed until the
LED starts flashing slower. The speakers will give a few beeps to indicate
the speakers are paired with each other. This will take about 30 sec.
3. To pair both speakers with your mobile device, turn on Bluetooth on your
mobile device. Usually you can find this on your phone or tablet in the
settings
4. Now press on just one (left) of the speakers again the phone button until the
led starts flashing fast. On your phone or tablet you will see now MiTone
MITSP65. Press connect on your mobile device.
5. After connecting the LED on the speaker will stop flashing on one speaker,
the other speaker LED with flash slowly. The speakers are paired with your
mobile device.
6. Hold the or Button on the unit to adjust the system volume.
7. Press or button to select Previous song and next Song.
NOTE :You need to do this set up ones. After pairing the speakers will be
automatically paired the next time you switch on.If this is not the case, repeat the
steps above.
RE AR V IE W
DC 5VLINE-IN ON/OFF
1 3 42
VOL+/VOL /
VOL+/
VOL /
VOL+/
VOL /
VOL+/
VOL /
5 6 7 8
Making Calls With A Bluetooth Mobile Phone
Before you make a call with the unit, you need to pair and link your
Bluetooth-enabled phone with the unit. Please refer to Pairing procedure
1. To answer a call, Press the button of Master unit (Left channel),
Now you can use the unit as a speakerphone.
2. Speak into the MIC and press the or Button on the unit and
mobile to adjust the call volume.
3. To end the call, press the Button.
NOTE: make sure you use the one with the solid blue led when use in
stereo mode.
VOL+/
VOL /
Pairing The Speakers For Mono Use
1. Slide the power switch at the back of the speaker to on. The speaker will
give a beeping sound. The blue LED light will flash quickly.
2. Go to settings on your smartphone or tablet and switch on Bluetooth.
3. On the display you will find MiTone MITSP65, press to connect. ( no
password requiered).
4. After pairing the blue LED on the speaker will stop flashing and turn into
solid blue.
5. Hold the or Button on the unit to adjust the system volume.
6. Press or button to select Previous song and next Song.
7. Press button to pause/play music
VOL+/
VOL /
VOL+/
VOL /
What the LED indicates in Stereo use
Power on both unit- The LED’s are flashing quickly and is in pairing search
mode.
After pairing- The led is solid blue on one speaker and flashes slowly on the
other speaker.
Charging- The led is red and will turn of when fully charged.
Charging The Battery
1. Use the included USB Charging cable , Plug one end into the DC 5V jack
located at the bottom of the unit, Plug the other end into a USB powered
port or any other USB AC adapter (not included).
2. The battery is fully charged in 2 - 2.5 hours .
3. The red LED light indicates that the unit is charging , The red LED turns
off when the battery is fully charged, You can disconnect the charging
cable when charging is complete.
To prevent the possibility of the battery from leaking,
heating, fire .please observe the following precautions:
Warnings
1: Please use attached USB charging cable in the package to charge unit
2: Please disconnect charge cable after fully charged the unit, Do not charge the unit
for long time after unit full charged
3: Do not immerse the product in water and seawater
4: Do not use and leave the product near a heat source as fire or heater
5: Do not place it into water , any other liquid ,Fire or any heater machine .
6: Do not strike or throw the product.
Cautions
1: Do not use or leave the product at very high temperature (for example, at strong
direct sunlight or a vehicle in extremely hot conditions).Otherwise, it can overheat
or fire or its performance will be degenerate and its service life will be decreased.
2: Do not use it in a location where static electricity is great, otherwise, the safety
devices may be damaged, which will cause hidden trouble of safety.
3: The batteries should be stored at room temperature, charged to about 30% to 50%
of capacity. In case of over-discharge, batteries should be charged for one time
every
4: months while storing and batteries should be discharge and charge after being
stored more than a year in order to activate it and restore energy.
5: Please following Waste battery recycling method to dispose the unit
Trouble Shooting Guide
Symptoms Possible Problems or Causes
Two speaker
unit can not
pair successful
Bluetooth Sound
starts to cut in and
cut out in Stereo
work mode
Distortion sound
or Noise in Stereo
work mode
Do please turn off the power of two speaker unit and
then re-open the power of two speaker unit, and
re-connect with audio device or Switch off audio device
and switch on again.
Music can't play
automatically after
call in Stereo work
mode
Please turn of the power of the two speakers and then
re-open the power. Follow the instructions on pairing in
stereo or use the quick guide.
Make sure your mobile device is not connected to any
other speaker system
Microphone
handsfree does
not work
If you want to use the speaker as a hands-free device
make sure you use the one with the solid blue led
when use in stereo mode.
After you use the speaker as a hands-free device the
music will stop when you take the call. After the call
the music will come back. If this is not the case press
play again on your mobile device.
This product bears the selective sorting symbol for waste electrical and
electronic equipment (WEEE).
This means that this product must be handled pursuant to European
Directive 2002/96/EC in order to be recycled or dismantled to minimize
its impact on the environment.
For further information, please contact your local or regional authorities.
If at any time in the future you should need to dispose of this product please
note that Waste electrical products should not be disposed of with household
waste.Please recycle where facilities exist.Check with your Local Authority or
retailer for recycling advice.(Waste Electrical and Electronic Equipment Directive)
www.mitone.eu
Guarantee
worldwide
What The LED Indicates
What the LED indicates in Mono use
Power on- The let is flashing quickly and is in pairing search mode.
After pairing- The led is solid blue
Charging- The led is red and will turn of when fully charged.
Aux Play Mode
1. Plug one end of the included 3.5 mm audio cable into the headphone or
line out jack of your audio device.
2. Plug the other end of the cable into the LINE IN jack located on the back
of the unit.
3. Slide the power switch of the speaker to ON position.
4. Turn on your audio device and play music. Make sure your audio device
is charged and turned to medium volume.
5. Adjust the volume of your audio device to the desired level.
6. When you use the aux cable you can only use one speaker at the time.
Stereo playback using the aux cable is not possible.
7. Hold the or Button on the unit to adjust the system volume.
VOL+/
VOL /