Mitsubishi Electric trium aria User manual

RVA : Création X GLASSON 10/99 Rédigé par Verifié par Approuvé par
ERB: MAJ exploded diagram 01/00 Written by Checked by Approuved by
V S C: MAJ charging meas. 05/00 X. GLASSON B. LEGORGEU G. LEBASTARD
I I
SO
IN
OS
N
S
Mitsubishi Electric Telecom Europe Version C
ZA le Piquet, 35370 Etrelles Date: 05/00
Phone: [phone]
Fax: [phone]
+LEVEL 2 SERVICE
FA9M037810
ARIA
(DUAL BAND)

Level 2 Service Manual
ARIA
Mitsubishi Electric Telecom Europe Version C
ZA le Piquet, 35370 Etrelles Date: 05/00
Phone: [phone]
Fax: [phone]
TABLE OF CONTENTS
1GENERAL DESCRIPTION...................................................................................................................1
2MAIN FEATURES OF TRANSCEIVER ..............................................................................................2
2.ADESCRIPTION OF TRANSCEIVER ........................................................................................................... 2
2.BIMEI LABEL....................................................................................................................................... 3
2.CART LABEL....................................................................................................................................... 3
2.DSIM LATCHING.................................................................................................................................. 4
3EXPLODED DIAGRAM AND SPARE PART LIST ............................................................................5
3.AEXPLODED DIAGRAM OF ARIA........................................................................................................... 5
3.BSPARE PART LIST OF ARIA.................................................................................................................. 6
4TEST AND MEASUREMENTS.............................................................................................................7
4.ACHARGING MEASUREMENTS................................................................................................................ 7
4.BE-GSM / DCS MEASUREMENTS .......................................................................................................... 8
4.b.1 Transmitter Power and Ramp profile......................................................................................... 8
4.b.2 Phase / Frequency / Time relationship....................................................................................... 8
4.b.3 Receiver Bit Error Rate (RX sensitivity) .................................................................................... 8
4.b.4 Handover between E-GSM 900 AND DCS 1800 standards ........................................................ 8
4.COPERATING INSTRUCTIONS ................................................................................................................. 9
4.DBUZZER AND SPEAKER TESTS ............................................................................................................ 10
5SERVICE SOFTWARES ..................................................................................................................... 11
5.ASOFTWARE DOWNLOAD WITH IPLTRIUM ........................................................................................... 11
5.a.1 How to install IPLTrium software and equipment ........................................................................ 11
5.a.2 Software description.................................................................................................................... 12
5.a.3 Start download ............................................................................................................................ 13
5.a.4 End of Download......................................................................................................................... 13
5.BSETTINGS DOWNLOAD WITH MS TOOLS ............................................................................................ 14
5.b.1 How to install MS Tools software and equipment..................................................................... 14
5.b.2 Software description................................................................................................................ 15
5.b.3 Start download ........................................................................................................................ 15
5.b.4 End of download...................................................................................................................... 17
5.CHOW TO PRINT LABELS USING MS TOOLS .......................................................................................... 18
5.c.1 Equipment, Software and drivers required................................................................................... 18
5.c.2 Print labels.................................................................................................................................. 19
6SOFTWARE AND SETTING VERSION............................................................................................ 20
7OPERATOR DEBUGGING................................................................................................................. 20

Level 2 Service Manual
ARIA
Mitsubishi Electric Telecom Europe Version C
ZA le Piquet, 35370 Etrelles Date: 05/00
Phone: [phone]
Fax: [phone]
1General Description
ARIA is designed for use in a E-GSM/DCS network. This phone operates and complies with the ETSI GSM
Phase 2 specifications.
Main features
•Weight : 85 g
•80 hours idle time
•1.5 hour conversation time
•Graphic LCD
•Data fax fonction included
•TEGIC fonction (word recognition)
Standart kit includes following items :
•Tranceiver (retractable antenna type)
•Battery pack (3.8V 580mA Li-ion)
Reference : FZ-2538A
•AC/DC adapter for battery rapid charging (5.5V 500mA)
Reference : FZA-0033A
Speech codec :
•ARIA uses a speech codec which
is able to switch from half rate (HR) to full rate (FR)
or to enhanced full rate (EFR) according to network and
the software & settings version.
•Enhanced full rate (EFR) allows better voice quality at
same rate as full rate.
•Half rate (HR) is coding on 6.5 kb/sec (1/2 than full rate)
the network may put two customers on one timeslot.
each customer will use this timeslot every two frames.
Actual size

Level 2 Service Manual
ARIA
Version C Mitsubishi Electric Telecom Europe
Date: 05/00 ZA le Piquet, 35370 Etrelles
Phone: [phone]
2/20 Fax: [phone]
2Main Features of Transceiver
2.a Description of transceiver
For M4 family, to enter test mode is not possible directly from mobile. This is possible only using a PC and the
relevant software .
Retractable
antenna
Extend the
antenna fully
when sending or
receiving a call
LED
Call and battery
charge indicator
Headset socket
Connect the
headset here
Grafic display
Telephone
number, menus,
message etc. here
Softkeys
Earpiece
You can hear the
caller’s voice here
Call/Send key
Dials displayed
number and
answers calls
On/Off key
Hold down to turn
on or off the
phone
Options key
Microphone
End key
Press to end a call
or return to stanby
display
Volume key
TEGIC key
TEGIC on or off
Alphanumeric
keys
To enter text and
telephone
numbers
Multifunction
key

Level 2 Service Manual
ARIA
Mitsubishi Electric Telecom Europe Version C
ZA le Piquet, 35370 Etrelles Date: 05/00
Phone: [phone]
Fax: [phone]
2.b IMEI label
IMEI label stands for International Mobile Equipment Identity. The IMEI label is stuck on the rear case of the
terminal. It is held in the logic circuitry of the main board itself. If the main board is changed then IMEI will
change.
Date Code is made of 3 digits and indicates the date of shipment from factory.
For example: in I11, I stands for 1999 and 11 for November (12 for december).
Bar code indicates 15 digits 123456 45 456789 4 ( for example) of the IMEI written in plain letters above the
bar code:
- 123456 : The 6 first digits indicate the Type Approval Code. It is different according the type of mobile.
- 45 : These 2 digits are allocated to production site.
- 456789 : The 6 last digits are a sequential number, it is different for each mobile.
- 4: Check digit.
2.c ART Label
The Label Art Plate identifies the type of assembly and test the mobile has been through.
XXXXXXXXXX : 10 characters for the article code of the terminal.
A: 1 character for the assembly version of M/U.
C: 1 character for the board version.
WW : 2 characters related to production site.
Logo Norme
Europe
Kit designation Date code
Made in France
Information
IMEI number
and bar code

Level 2 Service Manual
ARIA
Version C Mitsubishi Electric Telecom Europe
Date: 05/00 ZA le Piquet, 35370 Etrelles
Phone: [phone]
4/20 Fax: [phone]
2.d SIM Latching
SIM Lock consists in restricting the use of the terminal to a family of SIM cards. For the SIM Lock, three
principal informations are used. These informations are read from data fields in the SIM card.
1°) IMSI (International Mobile Subscriber Identity), 15 Digits :
Example of IMSI : 208 01 55 12312312
208 = MCC = Mobile Country Code (ex : 208 for France)
01 = MNC = Network Country Code (ex : 01 for FT)
55 = NS = Network Subset
12312312 = Indifferent serial number
2°) Group IDentifier 1 (GID1):
This data field can contain digits or letters which identify a family of SIM
Ex : XX for a type for of prepaid SIM card of Service provider Y
3°) Group IDentifier 2 (GID2) :
same as GID1 to identify a sub family of SIM.
Then, from this information, we have 5 types of latch :
1°) Network Level :
latch on MCC MNC of IMSI of the SIM only
(ex : only the cards 208 01 be able to operate the mobile.
Mitsubishi uses to call this latch NCK (NCK stands for “ Network Control Keys” and is the password to lock
the mobile at the network level)
2°) Network Subset Level :
Latch on MCC, MNC and digit 6 and 7 of the IMSI
Ex : latch on 208 01 55, only the SIM cards with an IMSI starting with 208 01 55 will operate the mobile.
Mitsubishi uses to call this latch NSCK (Network Subset Control Key)
3°) Service provider level :
latch on Network (value of MCC MNC) and value of GID1 data field.
Ex : latch on the value “XX” in GID1 and MCC MNC=208 01, only the SIM cards of service provider Y with
XX stored in data field GID1 will operate the mobile.
Mitsubishi uses to call this latch SPCK (Service Provider Control Key)
4°) Corporate Provider Level :
latch on network (value of MCC and MNC) and a value stored in GID2
Mitsubishi uses to call this latch CPCK (Corporate Provider Control Key)
5°) IMSI level
latch on the complete IMSI of one SIM card.
Only one SIM card corresponding to the correct IMSI operates the mobile. Usually, this latch is done in an
automatic way (the first SIM card inserted in the mobile is the only SIM which can be usesd by this mobile).
General information :
To lock /unlock a mobile, you need 8 digits password for each level concerned, and each mobile (one set of
passwords for one IMEI). These passwords are calculated with a special algorithm. You have only 10 attempts
to unlock correctly a mobile. After 10 unsuccessful attempts, the mobile is permanently blocked.
To enter the unlock procedure, you need to access special menus with specific access codes.

Level 2 Service Manual
ARIA
Mitsubishi Electric Telecom Europe Version C
ZA le Piquet, 35370 Etrelles Date: 05/00
Phone: [phone]
Fax: [phone]
3EXPLODED DIAGRAM AND SPARE PART LIST
3.a Exploded Diagram of ARIA

Level 2 Service Manual
ARIA
Version C Mitsubishi Electric Telecom Europe
Date: 05/00 ZA le Piquet, 35370 Etrelles
Phone: [phone]
6/20 Fax: [phone]
3.b Spare part list of ARIA
Position Designation Reference
ANTENNA 7N14153510
CAP RF F431932010
CASE ASSY V237 PEARL SILK F232909G10
COVER ASSY V237 PEARL SILK F232908G10
FLIP ARIA PEARL SILK LOGO TRIUM FK8L011610
FLIP ARIA PEARL SILK LOGO MITSUBISHI FK8L011810
CASE ASSY V237 SABLE SILK F232909G20
COVER ASSY V237 SABLE SILK F232908G20
FLIP ARIA SABLE SILK LOGO TRIUM FK8L011710
FLIP ARIA SABLE SILK LOGO MITSUBISHI FK8L011910
CUSHION-LCD F335839010
HINGE-L 1N1129701A
HINGE-R 1N1129711A
HOLDER MIC F432075010
KEY-RUBBER F233074010
LABEL ART FS2D003110
LCD MODULE 5U88338010
MIKE 7R00000070
MOTOR VIBRATOR 7T73921410
PIPE-ANT-213 F431660010
SCREW PTP1,7*5-TPR 1B79921610
SCREW PTP2,0*8-TPR-NI 1B79921410
RUBBER I/O F432010010
SHIELD BOX-F F133132G10
SHIELD BOX-R F133133010
WINDOW ARIA F233232010
EL/SW-MODULE ARIA 6R57172510
FPC ARIA F232910G10
RECEIVER 7R14377410
SPACER-SHIELD-2 F432185010
CUSHION-BB F432183010
SPACER-SHIELD-1 F432184010
SOCKET-MIC 7R11489010
CUSHION-ANT F432262010
Connectors of ARIA
Position Designation Reference
J100 CONNECTOR I/O M4 SO 6T78676110
J101 BATTERY PROBE CONNEC 6T89736010
J200 CONNECTOR(ETP) 6T84927810
J201 CONNECTOR(ETP) 6T84927810
J300 CONNECTOR(ETP) 6T84937610
J900 CONNECTOR RF 6T25974510

Level 2 Service Manual
ARIA
Mitsubishi Electric Telecom Europe Version C
ZA le Piquet, 35370 Etrelles Date: 05/00
Phone: [phone]
Fax: [phone]
4TEST AND MEASUREMENTS
4.a Charging measurements
To check the charging, we uses a modified AC/DC and an ampermeter connected as follow :
When you plug the charger into the wall socket, the charging current is displayed by ampermeter
The charging indicator scroll on the LCD and the red top led lights up.
During pre-charge, the value of the curent is 84 mA (measurment without backlight)
During rapid charge, the value of the current is 610 mA (measurment without backlight)
For more details about charging, see the LEVEL 3 SERVICE MANUAL FA9M037910 at page 5.
Mobile with
empty battery
without SIM

Level 2 Service Manual
ARIA
Version C Mitsubishi Electric Telecom Europe
Date: 05/00 ZA le Piquet, 35370 Etrelles
Phone: [phone]
8/20 Fax: [phone]
4.b E-GSM / DCS measurements
4.b.1 Transmitter Power and Ramp profile
These two are interrelated, since the power ramp shape and its final peak value is stored in EEPROM as
adjustment values.
The peak power output must lie within 3 dB of specification and be flat to within 0.5 dB over the active period.
The ramp profile is designed to give minimum harmonics, and hence it is important to ensure it is adhered to.
Power ramp profile must be checked on all frequencies (in practice channels 975, 37 and 124 for the 900 MHz
band and channels 512, 698 and 885 for the 1800 MHz band). In conclusion, the ramp must fit the mask at all
frequencies and all power levels. The mask is usually stored in the radiocommunication tester. The test will
also be available to cover the frequency and power range automatically.
4.b.2 Phase / Frequency / Time relationship
This is a test of the quality of the modulation including the IQ balance and the Gaussian filters. The phase of
the carrier changes according to the arrival of 1s and 0s. Phase error must not be more than 20° peak and 5°
RMS.
4.b.3 Receiver Bit Error Rate (RX sensitivity)
The specification is a Bit Error Rate (BER) of better than 2.44% for an input signal : -102 dBm for the E-GSM
900 band, and –100 dBm for the DCS 1800 band. There should be no error for -90 dBm to -20 dBm input
signal. The maximum workable error rate is 13%.
It is important that BER and RX sensitivity is good since measures of RXLEV (from -103 to -41 dBm) and
RXQUAL (from 0 to 7) are reported back to the base station on the SACCH to assist in handovers and power
level control. Errors in reporting will lead to sub optimum uses of channel space, or interference to others.
4.b.4 Handover between E-GSM 900 AND DCS 1800 standards
The M4 dual band may handover from the E-GSM 900 band to the DCS 1800 band automatically. If the
subscribed network has frequencies in both bands, the M4 dual band will work either in 900 MHz or 1800 MHz
band depending on the availability of frequencies.

Level 2 Service Manual
ARIA
Mitsubishi Electric Telecom Europe Version C
ZA le Piquet, 35370 Etrelles Date: 05/00
Phone: [phone]
Fax: [phone]
4.c Operating instructions
1. Insert Test SIM in the mobile
2. Connect a charged battery
3. Make a call with a RADIOCOMMUNICATION TESTER and check the following parameters,
or uses the autotest (CMD55 or CMD55 under MTS or Wavetek 4107)
Power levels : check the transmitted power (dBm)
E-GSM 900
PCL Power Level (dBm) tolerance DCS 1800 PCL Power level (dBm) tolerance
5 33 +/-2dB 0 30 +/-2dB
6 31 +/-3dB 1 28 +/-3dB
7 29 +/-3dB 2 26 +/-3dB
8 27 +/-3dB 3 24 +/-3dB
9 25 +/-3dB 4 22 +/-3dB
10 23 +/-3dB 5 20 +/-3dB
11 21 +/-3dB 6 18 +/-3dB
12 19 +/-3dB 7 16 +/-3dB
13 17 +/-3dB 8 14 +/-3dB
14 15 +/-3dB 9 12 +/-4dB
15 13 +/-3dB 10 10 +/-4dB
16 11 +/-5dB 11 8 +/-4dB
17 9 +/-5dB 12 6 +/-4dB
18 7 +/-5dB 13 4 +/-4dB
19 5 +/-5dB 14 2 +/-5dB
15 0 +/-5dB
RF Cable NN 50 OHMS 0.8
(FT7Y005610)
NSMA ADAPTATOR FEMALE
(FT7Y010010)
ARIA RF CABLE L300
(FT7Y010410)
Mobile with full
battery
RADIOCOMMUNICATION TESTER

Level 2 Service Manual
ARIA
Version C Mitsubishi Electric Telecom Europe
Date: 05/00 ZA le Piquet, 35370 Etrelles
Phone: [phone]
10/20 Fax: [phone]
Power ramping: Check the burst fit the mask below
RX levels : Check the values for differents signal strenght
RX LEVEL RSSI (dBm)
0Less than -110 dBm
1-110 to -109
2-109 to -108
27 -84 to -83
50 -61 to -60
62 -49 to -48
63 Better than -48
Bit error : Check the value for differents type
Check the Reception Bit Error Rates (RBER) and Frame Error Rates on channels 1,62 and 124 at –102dBm for
GSM band and on channels 512, 698 and 885 for the DCS band according the following specifications :
Bit error type Value
RBER Class Ib < 0.41 %
RBER Class II < 2.44 %
FER < 0.12%
4.d Buzzer and Speaker tests
Insert a test SIM in mobile set with battery.
The volume levels of the ring tone, key tones and incoming audio can be individually adjusted in the setting
menu.
•Press Menu choose Settings by pressing and validate by pressing for Select
•Choose Tones by pressing and validate by pressing for Select
•Choose Volume by pressing and validate by pressing for Select
And adjust Ring and Conversation to check buzzer and speaker
+4
+1
-6
-1
-30
-70
(dB)
Level
8µS
10µS
8µS
10µS
542.8µS
147 « useful » bits

Level 2 Service Manual
ARIA
Mitsubishi Electric Telecom Europe Version C
ZA le Piquet, 35370 Etrelles Date: 05/00
Phone: [phone]
Fax: [phone]
5Service SOFTWARES
The software in the mobile consist of two files downloaded independantly.
The corp of this software is downloaded using IPLTrium.
The settings file (ringing, customization…) is downloaded with MS Tools. MS tools also allows to enter test
mode in order to reset usesr data (security code) , to print labels (imei & factory name plate), to reset the
permantly blocked indicator providing you have the access rights.
5.a Software download with IPLTrium
5.a.1 How to install IPLTrium software and equipment
Equipment description : Mobile without battery
To COM1
IPL trium is available on Windows 95, 98, NT4 OS and is made of differents files :
(These files can be provided under one ZIP file)
To install IPLTRIUM software, create a folder named M4_soft_aria
And copy the files into this folder. In this folder, create two new folders named Software and Setting
In the Software folder, copy the software file (*.BIN) available for the mobile you have to download.
You are now ready to download the software.
AC/DC
FZA0033A
PC Cable S4 & D
FK8L011110

Level 2 Service Manual
ARIA
Version C Mitsubishi Electric Telecom Europe
Date: 05/00 ZA le Piquet, 35370 Etrelles
Phone: [phone]
12/20 Fax: [phone]
5.a.2 Software description
Adjust the serial parameters as folowing
Click here to adjust
Serial Parameters
Progress Indicator
Information Window

Level 2 Service Manual
ARIA
Mitsubishi Electric Telecom Europe Version C
ZA le Piquet, 35370 Etrelles Date: 05/00
Phone: [phone]
Fax: [phone]
5.a.3 Start download
5.a.4 End of Download
When download is completed, press the mobile Power key (mobile shuts down), disconnect the ARIA PC
Cable, connect a full battery and press the power key (mobile switches on).
Click here to
Startdownload
Click here to select the
Sofware for download
Click here to select
Flash Loader
(iplm4so.bin for aria (SOcial))

Level 2 Service Manual
ARIA
Version C Mitsubishi Electric Telecom Europe
Date: 05/00 ZA le Piquet, 35370 Etrelles
Phone: [phone]
14/20 Fax: [phone]
5.b Settings download with MS Tools
5.b.1 How to install MS Tools software and equipment
Equipment description : Mobile with full battery
To COM1
MS Tools is available on Windows 95, 98, NT4 OS and to install it you need theses 3 files :
Setup procedure :
1Launch Setup.exe
2Click on Finish
3Click on OK
MS Tools is now installed on your computer and available in your START menu
You are now ready to download the setting file.
PC Cable S4 & D
FK8L011110

Level 2 Service Manual
ARIA
Mitsubishi Electric Telecom Europe Version C
ZA le Piquet, 35370 Etrelles Date: 05/00
Phone: [phone]
Fax: [phone]
5.b.2 Software description
5.b.3 Start download
In TestMode menu, click on Start from NormalMode, then information window displays Operation completed
Test Mode menu :
TEST MODE enter and exit
Mobile menu :
Download perso
Initialization data users
Mobile identification
Exit:
To quit MS Tools
(Click on is not availlable)
Informatio
n window Version of MS Tools
Informatio
n window

Level 2 Service Manual
ARIA
Version C Mitsubishi Electric Telecom Europe
Date: 05/00 ZA le Piquet, 35370 Etrelles
Phone: [phone]
16/20 Fax: [phone]
In Mobile menu, click on Download Personification, then, choose the right settings file and valid by select
information window displays Operation completed
Informatio
n window

Level 2 Service Manual
ARIA
Mitsubishi Electric Telecom Europe Version C
ZA le Piquet, 35370 Etrelles Date: 05/00
Phone: [phone]
Fax: [phone]
5.b.4 End of download
In TestMode menu, choose Stop and go back to NormalMode, then information window displays Operation
completed
Informatio
n window