Mitsubishi Electric City Multi PUHY-P192TSKMU-A Owner's manual

Job Name: Location:
Engineer Name: Contractor:
System No.: Date:
Model: PUHY-P192TSKMU-A
(Consists of One PUHY-P120TKMU-A, One PUHY-P72TKMU-A and One CMY-Y100CBK3 Twinning Kit)
OUTDOOR VRF HEAT PUMP SYSTEM FEATURES
• 3-phase, 208/230V
• Modular variable refrigerant flow (VRF) systems;
smaller capacity units can be piped together to form a single,
large-capacity two-pipe system
• Required Twinning Kit allows for easy field piping connection
• Selectable fan static, 0.12 or 0.24"WG external static pressure;
factory set to 0"WG
• Connects to CITY MULTI indoor units; controlled via
CITY MULTI Controls Network (CMCN)
• External finish: Pre-coated Galvanized-steel Sheets
• Operating Temperature Range
Cooling (Outdoor): 23° ~ 115°F (-5° ~ +46°C) DB
Heating (Outdoor): -4° ~ +60°F (-20° ~ +16°C) WB
OPTIONAL PARTS
□Twinning Kit*.…………………………………...…….CMY-Y100CBK3
□T-Branch Joint (≤ 72,000 Btu/h)………………..........CMY-Y102SS-G2
□T-Branch Joint (≤ 144,000 Btu/h)……………….…....CMY-Y102LS-G2
□T-Branch Joint (≤ 234,000 Btu/h)……………….........CMY-Y202S-G2
□Header (4-Branch;≤72,000 Btu/h)........………………CMY-Y104C-G
□Header (8-Branch;≤144,000 Btu/h)......………………CMY-Y108C-G
□Header (10-Branch;≤234,000 Btu/h)....………………CMY-Y1010C-G
* Twinning Kit is necessary to combine the refrigerant flows of the
modules and is sold separately.
Specifications System Module 1 Module 2
Unit Type PUHY-P192TSKMU-A PUHY-P120TKMU-A PUHY-P72TKMU-A
Nominal Cooling CapacityBtu/h 192,000 120,000 72,000
Nominal Heating CapacityBtu/h 215,000 135,000 80,000
External Dimensions (H x W x D)In. / mm Refer to Module Data 65 x68-29/32 x 29-5/23 /
1,650 x1,750 x740
65 x36-1/4 x 29-5/32 /
1,650 x920 x 740
Net Weight Lbs. / kg 1,127 / 511 697 / 316 430 / 195
Electrical Power Requirements Voltage, Phase, Hertz Refer to Module Data** 208 / 230V, 3-phase, 60Hz**
Cooling Power Input kW 14.81 Refer to System Data
Heating Power Input kW 16.91
Cooling Current (208/230V)R.L.A. 45.6 / 41.3 Refer to System Data
Heating Current (208/230V)R.L.A. 52.1 / 47.1
Minimum Circuit Ampacity
(MCA)** ARefer to Module Data** 45 / 42** 25 / 23**
Maximum Breaker Size** ARefer to Module Data** 50** 30**
Maximum Overcurrent Protection** ARefer to Module Data** 73 / 67** 42 / 38**
Piping Diameter
Refer to System Data
From Twinning Kitto Indoor Units
(Brazed) (In. /mm)
Liquid (High Pressure) 5/8 / 15.88
Gas (Low Pressure) 1-1/8 / 28.58
From Modules to Twinning Kit
(Brazed) (In. / mm)
Liquid (High Pressure) Refer to Module Data 1/2 / 12.7 3/8 / 9.52
Gas (Low Pressure) 1-1/8 / 28.58 7/8 x 22.2
Indoor Unit Total Capacity 50 to 130% of ODUs Refer to System Data
Model / Quantity P06 ~ P96 / 2 to 41
Sound Pressure Levels dB(A) 62.5 60.0 58.0
Fan
Refer to Module Data
Type x Quantity Propeller Fan x 2 Propeller Fan x 1
Airflow Rate CFM 11,300 6,200
Direct-drive InverterMotor Output kW 0.92 + 0.92 0.92
Compressor Operating Range 6% to 100% Refer to System Data
Compressor Type x Quantity
Refer to Module Data
Inverter-driven Scroll Hermetic x 1 Inverter-driven Scroll Hermetic x 1
Compressor Motor Output kW 8.1 5.5
Compressor Crankcase Heater kW - -
Refrigerant Refer to Module Data R410A
Lubricant MEL32
High-pressure Protection Device
Refer to Module Data
601 psi / 4.15 MPa 601 psi / 4.15 MPa
Compressor / Fan Protection Device Overheat Protection / Thermal Switch Overheat Protection / Thermal Switch
Inverter Protection Device Overheat / Overcurrent ProtectionOverheat / Overcurrent Protection
Blue FinAnti-corrosion Protection: Cellulose- and polyurethane-resin coating treatment applied to condenser coil that protects it from air contaminants;
≥1μm thick; Salt Spray Test Method - no unusual rust development to 480 hours.
PUHY-P120TKMU-A
** Each individual module requires a separate electrical connection. Reference electrical data for each individual module.
PUHY-P72TKMU-A

Module : PUHY-P192TSKMU-A – DIMENSIONS
ø28.58(1-1/8) ø15.88(5/8)
CMY-Y100CBK3
PUHY-P72TKMU-A(-BS)
PUHY-P120TKMU-A(-BS)
PUHY-P192TSKMU-A(-BS)
b
a
Gas
Liquid
Outdoor unit 2 Outdoor unit 1
Indoor unit~Twinning pipe
Outdoor Twinning Kit(optional parts)
Component unit name
Package unit name
Twinning pipe connection size
Note 1.Connect the pipes as shown in the figure above. Refer to the table above for the pipe size. 2.Twinning pipes should not be tilted more than 15 degrees from the horizontal plane. Be sure to see the Installation Manual for details of Twinning pipe installation.
3.The pipe section before the Twinning pipe (sections "a" and "b" in the figure) must have at least 500mm(19-11/16) of straight section
(*including the straight pipe that is supplied with the Twinning pipe). 4.Only use the Twinning pipe by Mitsubishi (optional parts).
d or fc or e
Gas
Liquid
P72 P120
Unit model
Twinning pipe~Outdoor unit
Front view
Left view
To indoor unit
Liquid Twinning pipe<optional parts> Gas Twinning pipe<optional parts>
To indoor unit
Outdoor unit 2
Outdoor unit 1
Discharge air
Intake air
Intake air
Intake air
ø28.58(1-1/8) ø22.2(7/8)
ø12.7(1/2) ø9.52(3/8)
dfb
a
e
c
920(36-1/4)30(1-3/16)1750(68-29/32)
1650(64-31/32)
740(29-5/32)
PUHY-P192TSKMU-A(-BS)
Unit : mm(in.)

Module : PUHY-P120TKMU-A or 144TKMU-A – DIMENSIONS
(7/8)
(1-3/4)
(1-3/8)
(2-15/32) (1-11/32)
(2-1/16) (2-9/16)
(3-23/32)(5-29/32)
(5-17/32) (3-1/16)
(1/2)
(1/2)
(1-1/8)
(1-1/8)
(3/8)
(1/2)
Fan box
ø12.7 Brazed
ø12.7
ø28.58 Brazed
ø28.58
ø9.52 Brazed
Note1.Please refer to the next page for information regarding necessary spacing around the unit and foundation work. 2.At brazing of pipes, wrap the refrigerant service valve with wet cloth and keep the temperature of refrigerant service valve under 120°C(248°F).
Refrigerant pipe Service valve
Diameter
Model
Connecting pipe specifications
(ø12.7 Brazed)
PUHY-P144TKMU PUHY-P120TKMU
Gas Gas
3
(26-23/32~26-15/16)
(26-13/16)
(3-5/32)
(3-5/32)
=(5-29/32)X4
(2-25/32)
(11-15/16)
(4-25/32)
(5-23/32)
(3-5/16)
(1-3/16)
(1-3/16)
(3-23/32)
(5-31/32)
(7-23/32) (8-9/16)
(3-17/32) (3-1/16)
(23-5/8)
(25/32)
(25/32)
(13/16) (13/16)
(2-1/4) (2-1/4)
2
1
4
7
2X2-80(3-5/32)X35(1-13/32) Oval hole
<Sling hole>
56
Discharge air
Intake air
Intake air
Service panel
Intake air
2X3-14(9/16)X20(13/16) Oval hole
(Mounting pitch)
(Mounting pitch)
(Mounting pitch)
Control box
Refrigerant service valve <liquid>
Refrigerant service valve <gas>
Service panel
2X7-ø4.6(3/16) Hole (Make hole at the plastic fan guard for snow hood attachment)
<Snow hood attachment hole>
Refrigerant service valve <gas>
Refrigerant service valve <liquid>
(6-25/32)
(8-25/32)
ø34 Knockout hole
ø52 Knockout hole ø65 Knockout hole
ø43.7 or ø22.2 Knockout hole
ø62.7 or ø34.5 Knockout hole
150 × 94 Knockout hole
140 × 77 Knockout hole
Specifications
For transmission cables
For pipes
Bottom through hole Front through hole
Usage
For wires
Front through hole
Front through hole Bottom through hole Bottom through hole
Front through hole
NO.
*1 Expand the on-site piping and connect to the refrigerant service valve piping. *2 Use the pipe joint(field supply) and connect to the refrigerant service valve piping. *3 Indicates dimensions and connection specifications in the case the unit is used in combination with other outdoor units. *4 Furthest piping length (OU from IU) 40m(131ft)
*1 *3 *4
*2
*1
*2
58(2-5/16)
75(2-31/32)
541(21-5/16)
217
172
196
151
121
303
1347(53-1/16)
1650(64-31/32)
1750(68-29/32)
19.5
831(32-23/32)
831(32-23/32)
19.5
600=150X470
(740)
(29-5/32)
29.5 29.5
562(22-5/32)
740(29-5/32)
7789
80
795(31-5/16) 795(31-5/16)
80
681 (678~684)
140(5-17/32)
49(1-15/16)
54(2-5/32)
57
20
586(23-3/32) 57
20
223
145
590(23-1/4) 83(3-9/32)
150(5-29/32)
561(22-3/32)
516(20-11/32)
8494
Front view
Top view
Left side view
Bottom view
PUHY-P120,144TKMU-A(-BS)
Unit : mm(in.)
1
2
3
4 5
6
7
> =
Liquid Liquid

Module : PUHY-P72TKMU-A – DIMENSIONS
2. EXTERNAL DIMENSIONS
(7/8)
(1-3/4)
(1-3/8)
(2-15/32) (1-11/32)
(2-1/16) (2-9/16)
(3-23/32)(5-29/32)
(5-17/32) (3-1/16)
(1-1/8)(3/8)(7/8)
(3/8) ø28.58ø9.52
PUHY-P72TKMU
ø22.2 Brazed
ø9.52 Brazed
Gas
Connecting pipe specifications
Service valveModel
Diameter
Liquid
Refrigerant pipe
Liquid Gas
Note1.Please refer to the next page for information regarding necessary spacing around the unit and foundation work. 2.At brazing of pipes, wrap the refrigerant service valve with wet cloth and keep the temperature of refrigerant service valve under 120°C(248°F).
(8-9/16)
Control box
<Snow hood attachment hole>
2X5-ø4.6(3/16) Hole (Make hole at the plastic fan guard for snow hood attachment)
(2-25/32) =(5-29/32)X4
(23-5/8)
(11-15/16)
(3-17/32)
Service panel
Intake air
Intake air
Intake air
Discharge air
(6-25/32)
(8-3/4)
(2-5/32)
(13/16)(13/16)
(2-1/4)
(2-1/4)
Refrigerant service valve <gas>
Refrigerant service valve <liquid>
(4-25/32)
(7-23/32)
(5-3/4)
(3-9/32)
Refrigerant service valve <liquid>
Refrigerant service
valve <gas>
(Mounting pitch)
(3-5/32) (3-5/32)
(26-13/16)
(678~684)
(Mounting pitch)
(26-23/32~26-15/16) (1-3/16)
(1-3/16)
(3-23/32)
(2-31/32)
(25/32) (25/32)
(7-15/16)
(8-3/4)
(8-3/4)
(9-29/32)
(6-31/32)
7
4
3
1
2X2-14(9/16)X20(13/16) Oval hole
2X2-80(3-5/32)X35(1-13/32) Oval hole
<Sling hole>
2
6 5
2
6 5
ø34 Knockout hole
ø52 Knockout hole ø65 Knockout hole
ø43.7 or ø22.2 Knockout hole
ø62.7 or ø34.5 Knockout hole
150 × 94 Knockout hole
140 × 77 Knockout hole
Specifications
For transmission cables
For pipes
Bottom through hole Front through hole
Usage
For wires
Front through hole
Front through hole Bottom through hole Bottom through hole
Front through hole
NO.
*1 Expand the on-site piping and connect to the refrigerant service valve piping. *2 Use the pipe joint(field supply) and connect to the refrigerant service valve piping.
*2
*1
217
58(2-5/16)
75
201
Left side view
Top view
Front view
Bottom view
145(5-23/32)
740(29-5/32)
140(5-17/32)
89 77(3-1/16)
3031347(53-1/16)
1650(64-31/32)
600=150X4
150(5-29/32)
70
19.519.5
920(36-1/4)
881(34-11/16)
222
29.5
29.5 681
80 760(29-15/16) 80
(740)(29-5/32)
29.5
29.5
54
57
20
586(23-3/32)
20
57
94 84(3-5/16)
222
172
222 150(5-29/32)
251 83
177
121
146
196
PUHY-P72TKMU-A(-BS)
Unit : mm(in.)
1
2
3
4 5
6
7

Mitsubishi Electric Sales Canada Inc.
www.MitsubishiElectric.ca
Specifications are subject to change without notice.
SB_PUHY-P192TSKMU-A_201206
Mitsubishi Electric Air Conditioning & Refrigeration Systems Wo rks acquired ISO
based on a review of quality warranties for the production of refrigeration and air
conditioning equipment.
ISO Authorization System
The ISO 9000 series is a plant authorization system relating to quality warranties as
development, production, installation and auxiliary services" for products built at
an authorized plant.
Mitsubishi Electric Air Conditioning & Refrigeration Systems Works acquired environmental
The ISO 14000 series is a set of standards applying to environmental protection set by the
International Standard Organization (ISO).
Twinning Kit: CMY-Y100CBK3
1-15/16"
(2 pcs.)
(2 pcs.)
3-7/8"
9-1/2"
7-7/32"
3-9/32"
19-29/32"
13-15/32"
23-5/32"
6-5/16"
2-15/32"
1-15/16"
2-15/32"
Distributer Distributer
Pipe cover
(Dot-dashed part)
1/2"
1/2"
1/2"
1/2"
Local brazing
Note 2
5/8"
5/8"
1-1/8"
Note 2
1"
7/8"
1"
7/8"
Pipe cover
(Dot-dashed
part)
Local brazing
1-1/8"
(2 pcs.)
7/8"
3/4"
1/2"
5/8"
1/2" 3/8"
1-1/8"
7/8"
For Gas pipe: For Liquid pipe:
ID: Inner Diameter OD: Outer Diameter
Ref.: CMY_Y100VBK2_EXD_EUDB_SI
in.
CMY-Y100CBK3
<Reducer(Accessory)>
The angle of the branch pipe for high pressure is within against the horizontal plane.
2. Use the attached pipe to braze the port-opening of the distributer.
3. Pipe diameter is indicated by inside diameter.
4. Only use the Twinning pipe by Mitsubishi (optional parts) .
Note 1. Reference the attitude angle of the branch pipe below the fig.
Distributer
15
15
Notes: