Mitsubishi Electric Mr.Slim Zuba Central User manual

Zuba Central
Heat Pump
User Manual
EnglishU
Page 1 of 23

Introduction
The Zuba-Central is a Heat Pump using Hyper Heat technology. The Zuba-Central
consists of outdoor unit and multi position ducted air handling indoor unit which are
connected together and controlled by a PAR 21MAA controller.
Application
Constant energy price increases in Canada and around the globe is increasing the
consumer’s requirements to source more efficient ways to cool and heat their homes.
The Zuba-Central Hyper Heat Pump can save energy and reduce greenhouse gas
emissions due to its high seasonal operation efficiency in both cooling and heating
seasons. In addition to this the new two phases liquid gas injection technology allows
high heating output at ambient temperatures below -30°C. The system is available with
auxiliary back-up heating options of hydronic hot water, electrical resistance heat or SCR
ducted heater.
Emergency Auxiliary back-up heat is also activated in case of system malfunction.
Page 2 of 23

Contents
Safety Precautions 3
Zuba-Central controller --PAR21MAA 5
Screen Configuration 6
Setting the Day of the Week and Time 8
Operation 9
Timer 11
Error Codes indication 22
User maintenance 23
Safety Precautions
•Before installing the unit, make sure you read all the “Safety Precautions”.
•The “Safety Precautions” provide very important points regarding safety.
Make sure you follow them.
•Please report to or obtain necessary permits from Local Electrical authority
before connection to the system
Symbols used in the text
Warning:
Describes precautions that should be observed to prevent danger of injury or death
to the user
Caution:
Describes precautions that should be observed to prevent damage to the unit
Page 3 of 23

Warnings:
•For appliances when installed should not be accessible to the general public.
•The unit must not be installed by the user. Ask the dealer or an authorized
company to install the unit. If the unit is installed improperly, water leakage,
electric shock or fire may result.
•Do not stand on, or place any items on the unit.
•Do not splash water over the unit and do not touch the unit with wet hands.
An electric shock may result.
•Do not spray combustible gas close to the unit. Fire may result.
•Do not place a gas heater or any other open-flame appliance where it will
be exposed to the air discharged from the unit. Incomplete combustion may
result.
•Do not remove the front panel or the fan guard from the outdoor unit or the
panels from the indoor unit when it is running.
•When you notice exceptionally abnormal noise or vibration, stop operation,
turn off the power switch, and contact your dealer.
•Never insert fingers, sticks etc. into the intakes or outlets.
•If you detect odd smells, stop using the unit, turn off the power switch and
consult your dealer. Otherwise, a breakdown, electric shock or fire may
result.
•This system is NOT intended for use by children or infirm persons without
supervision.
•Young children must be supervised to ensure that they do not play with the
air conditioner.
•If the refrigeration gas blows out or leaks, stop the operation of the system,
thoroughly ventilate the room, and contact your dealer.
Caution:
•Do not use any sharp object to push the buttons, as this may damage the
remote controller.
•Never block or cover the indoor or outdoor unit’s intakes or outlets.
Disposing of the unit
•When you need to dispose of the unit, consult your dealer.
Page 4 of 23

Zuba-Central controller
Page 5 of 23

How to use the Zuba-Central controller
Screen Configuration
Page 6 of 23

Screen Types
For details on setting the language for the remote controller display, refer to
section 8. Function Selection.
The initial language setting is English.
•Function Selection of remote controller:
Set the functions and ranges available to the remote controller (timer
functions, operating restrictions, etc.)
•Set Day/Time
Set the current day of the week or time.
•Standard Control Screens
View and set the air conditioning system’s operating status
•Timer Monitor
View the currently set timer (weekly timer, simple timer, or Auto Off
timer)
•Timer Setup
Set the operation of any of the timers (weekly timer, simple timer, or Auto
Off timer).
How to change the screen
A. Hold down both the Mode button and the Timer On/Off button for 2
seconds.
B. Press the Timer Menu button.
C. Press the Mode (Return) button.
D. Press either of the Set Time buttons (Back or Ahead)
To return to main screen
Hold down both the Mode button and the Timer On/Off button for 2
seconds.
Page 7 of 23

4. Setting the Day of the Week and Time
Note: The day and time will not appear if clock use has been disabled at Function
Selection of remote controller.
1. Press the or Set Time button (11) to show display [2].
2. Press the Timer On/Off (Set Day) button (9) to set the day.
Each press advances the day shown at [3]:
3. Sun > Mon > ...> Fri > Sat.
4. Press the appropriate Set Time button (11) as necessary to set the time.
As you hold the button down, the time display (at 4) will increment first in
one-minute intervals, then in ten-minute intervals, and then in one-hour
intervals.
5. After making the appropriate settings at Steps 2 and 3, press the Filter
button (4) to lock in the values.
6. Press the Mode button (2) to exit
Page 8 of 23

5. Operation
5.1. Turning ON/OFF
<To Start Operation>
Press the ON/OFF button.
• The ON lamp [1] and the display area will light up or come on.
Note: When the unit is restarted, initial settings are as follows.
Remote Controller settings
Mode Last operation mode
Temperature setting Last set temperature
<To Stop Operation>
Press the ON/OFF button again.
• The ON lamp [ 1] and the display area go off.
Page 9 of 23

5.2. Mode select
Press the operation mode ( ) button and select the operation mode displays
in [2] above.
Cool Mode
Drying mode
Fan mode
Heating mode
Automatic (cooling/heating) mode <Only heat pump type>
Ventilation mode
Only indicated on Wired remote controller when LOSSNAY
connected
5.3. Temperature setting
To decrease the room temperature:
Press button (3) to set the desired temperature. The selected temperature is
displayed [3].
To increase the room temperature:
Press button (3) to set the desired temperature. The selected temperature is
displayed [3].
• Available temperature ranges are as follows:
Cooling/Drying: 19 - 30 °C, 67 - 87 °F
Heating: 17 - 28 °C, 63 - 83 °F
Automatic: 19 - 28 °C, 67 - 83 °F
• The display blinks either 8 °C - 39 °C, 46 °F - 102 °F to inform you if the room
temperature is lower or higher than the displayed temperature.
5.4. Fan speed setting
Pressing the Fan Speed button will display the follow
“NOT AVAILABLE” message
The ZUBA Central has fixed speeds for Heating and Cooling.
Page 10 of 23