Mitsubishi Electric PVA-A30AA4 User manual

SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS
SERVICE MANUAL
Model name
<Indoor unit>
Model name
<Indoor unit>
Series PVA
2015
PVA-A30AA4
PVA-A36AA4
PVA-A42AA4
INDOOR UNIT
HWE1406A.qx 3/19/15 9:01 AM Page 1

HWE1406A.qx 3/19/15 9:01 AM Page 2

CONTENTS
1. SAFETY PRECAUTION 2
2. PART NAMES AND FUNCTIONS 3
3. SPECIFICATION 4
4. FAN PERFORMANCE AND CORRECTED AIR FLOW 6
5. SOUND PRESSURE LEVELS 10
6. OUTLINES & DIMENSIONS 12
7. WIRING DIAGRAM 14
8. REFRIGERANT SYSTEM DIAGRAM 15
9. EATER CONTROL 16
10. UMIDIFIER CONTROL 19
11.ERV (ENERGY RECOVERY VENTILATION) CONTROL 20
12. TROUBLES OOTING 21
13. DISASSEMBLY PROCEDURE 34
HWE1406A.qx 3/19/15 9:01 AM Page 3

2
SAFETY PRECAUTION
1
1-1. ALWAYS OBSERVE FOR SAFETY
Cautions for units utilising refrigerant R410A
Use new refrigerant pipes.
Make sure that the inside and outside of refrige-
rant piping is clean and it has no contamination
such as sulfur hazardous for use, oxides, dirt,
shaving particles, etc.
In addition, use pipes with specified thickness.
Store the piping to be used indoors during
installation and both ends of the piping sealed
until just before brazing. (Leave elbow joints, etc.
in their packaging.)
Use ester oil, ether oil or alkylbenzene oil (small
amount) as the refrigerant oil applied to flares
and flange connections.
In case of using the existing pipes for R22, be careful with
the followings.
·For A36 and A42, be sure to perform replacement oper-
ation before test run.
·Change flare nut to the one provided with this product.
Use a newly flared pipe.
·Avoid using thin pipes.
Charge refrigerant from liquid phase of gas
cylinder.
If the refrigerant is charged from gas phase, composition
change may occur in refrigerant and the efficiency will be
lowered.
Do not use refrigerant other than R410A.
If other refrigerant (R22 etc.) is used, chlorine in refrige-
rant can cause deterioration of refrigerant oil etc.
Use a vacuum pump with a reverse flow check
valve.
Vacuum pump oil may flow back into refrigerant cycle and
that can cause deterioration of refrigerant oil etc.
Use the following tools specifically designed for
use with R410A refrigerant.
The following tools are necessary to use R410A refrigerant.
Handle tools with care.
If dirt, dust or moisture enters into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of com-
pressor.
Do not use a charging cylinder.
If a charging cylinder is used, the composition of refrigera-
nt will change and the efficiency will be lowered.
Flare tool
Electronic refrigerant
charging scale
Vacuum pump adaptor
Size adjustment gauge
Gauge manifold
Torque wrench
Gas leak detector
Charge hose
Tools for R410A
Contamination inside refrigerant piping can cause deterio-
ration of refrigerant oil etc.
If dirt, dust or moisture enters into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of com-
pressor.
If large amount of mineral oil enters, that can cause deterio-
ration of refrigerant oil etc.
Ventilate the room if refrigerant leaks during
operation. If refrigerant comes into contact with
a flame, poisonous gases will be released.
[1] Cautions for service
(1) Perform service after recovering the refrigerant left in unit completely.
(2) Do not release refrigerant in the air.
(3) After completing service, charge the cycle with specified amount of refrigerant.
(4) When performing service, install a filter drier simultaneously.
Be sure to use a filter drier for new refrigerant.
[2] Additional refrigerant charge
When charging directly from cylinder
·Check that cylinder for R410A on the market is syphon type.
·Charging should be performed with the cylinder of syphon stood vertically. (Refrigerant is charged from liquid phase.)
Before obtaining access to terminal, all supply
circuits must be disconnected.
1-2. CAUTIONS RELATED TO NEW REFRIGERANT
HWE1406A.qx 3/19/15 9:02 AM Page 2

3
Gravimeter
Unit
[3] Service tools
Use the below service tools as exclusive tools for R410A refrigerant.
No. Tool name Specifications
1Gauge manifold ·Only for R410A
·Use the existing fitting specifications. (UNF1/2)
·Use high-tension side pressure of 5.3MPa·G or over.
2Charge hose ·Only for R410A
·Use pressure performance of 5.09MPa·G or over.
3Electronic scale
4Gas leak detector ·Use the detector for R134a, R407C or R410A.
5Adaptor for reverse flow check ·Attach on vacuum pump.
6Refrigerant charge base
7Refrigerant cylinder ·Only for R410A ·Top of cylinder (Pink)
·Cylinder with syphon
8Refrigerant recovery equipment
PART NAMES AND FUNCTIONS
2
•Indoor Unit
Air inlet
Air outlet
Air
inlet Air
outlet
(1)Vertical (2)Horizontal Right
HWE1406A.qx 3/19/15 9:02 AM Page 3

4
Service Ref.
Power supply (phase, cycle, voltage)
Max. Fuse Size
Min. Circuit Ampacity A
A
External finish
Heat exchanger
Fan
Fan (drive) ×No.
F
Fan motor
an motor output kW
F.L.A
Airflow (Low-Mid-High) m3/min (CFM)
External static pressure Pa (in.WG)
Operation control & Thermostat
Sound pressure level
(Low-Mid-High) dB (A)
Drain pipe mm (in.)
Dimensions W mm (in.)
D mm (in.)
H mm (in.)
kg (lbs)
INDOOR UNIT
Weight
75Pa (0.30 in.WG)
125Pa (0.50 in.WG)
200Pa (0.80 in.WG)
1 phase, 60Hz, 208/230V
15
4.13
PVA-A30AA4
Galvanized steel cabinet - Powder coated Slate Gray
Plate fin coil
Sirocco fan ×1
0.121
3.3
17.3-21.1-24.8 (613-744-875)
75-125-200 (0.30-0.50-0.80)
Remote controller & built-in
30-34-38
32-36-40
35-39-43
19.05 (3/4) FPT
534 (21)
548 (21-5/8)
1378 (54-1/4)
64 (141)
Service Ref.
Power supply (phase, cycle, voltage)
Max. Fuse Size
Min. Circuit Ampacity A
A
External finish
Heat exchanger
Fan
Fan (drive) ×No.
F
Fan motor
an motor output kW
F.L.A
Airflow (Low-Mid-High) m3/min (CFM)
External static pressure Pa (in.WG)
Operation control & Thermostat
Sound pressure level
(Low-Mid-High) dB (A)
Drain pipe mm (in.)
Dimensions W mm (in.)
D mm (in.)
H mm (in.)
kg (lbs)
INDOOR UNIT
Weight
75Pa (0.30 in.WG)
125Pa (0.50 in.WG)
200Pa (0.80 in.WG)
1 phase, 60Hz, 208/230V
15
5.50
PVA-A36AA4
Galvanized Steel Cabinet - Powder coated Slate Gray
Plate fin coil
Sirocco fan ×1
0.430
4.40
22.3-27.1-31.9 (788-956-1125)
75-125-200 (0.30-0.50-0.80)
Remote controller & built-in
30-34-38
32-36-40
37-41-45
19.05 (3/4) FPT
635 (25)
548 (21-5/8)
1511 (59-1/2)
78 (172)
SPECIFICATION
3
Air
inlet
Air
outlet
Air inlet
Air outlet
(3)Horizontal left (4)Down flow
HWE1406A.qx 3/19/15 9:02 AM Page 4

5
Service Ref.
Power supply (phase, cycle, voltage)
Max. Fuse Size
Min. Circuit Ampacity A
A
External finish
Heat exchanger
Fan Fan (drive) ×No.
F
Fan motor
an motor output kW
F.L.A
Airflow (Low-Mid-High) m3/min (CFM)
External static pressure Pa (in.WG)
Operation control & Thermostat
Sound pressure level
(Low-Mid-High) dB (A)
Drain pipe mm (in.)
Dimensions W mm (in.)
D mm (in.)
H mm (in.)
kg (lbs)
INDOOR UNIT
Weight
75Pa (0.30 in.WG)
125Pa (0.50 in.WG)
200Pa (0.80 in.WG)
PVA-A42AA4
1 phase, 60Hz, 208/230V
15
5.63
Galvanized Steel Cabinet - Powder coated Slate Gray
Plate fin coil
Sirocco fan ×1
0.430
4.50
29.4-35.7-42.0 (1040-1262-1485)
75-125-200 (0.30-0.50-0.80)
Remote controller & built-in
34-38-42
36-40-44
39-43-47
19.05 (3/4) FPT
635 (25)
548 (21-5/8)
1511 (59-1/2)
78 (172)
HWE1406A.qx 3/19/15 9:02 AM Page 5

6
0
[0]
25
[0.10]
75
[0.30]
50
[0.20]
100
[0.40]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
15
[530]
20
[706]
25
[883]
29
[1024]
25
[0.10]
50
[0.20]
100
[0.40]
75
[0.30]
125
[0.50]
150
[0.60]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
15
[530]
20
[706]
25
[883]
29
[1024]
75
[0.30]
100
[0.40]
150
[0.60]
125
[0.50]
175
[0.70]
200
[0.80]
225
[0.90]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
15
[530]
20
[706]
25
[883]
29
[1024]
0
[0]
25
[0.10]
75
[0.30]
50
[0.20]
100
[0.40]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
15
[530]
20
[706]
25
[883]
29
[1024]
25
[0.10]
50
[0.20]
100
[0.40]
75
[0.30]
125
[0.50]
150
[0.60]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
15
[530]
20
[706]
25
[883]
28
[989]
75
[0.30]
100
[0.40]
150
[0.60]
125
[0.50]
175
[0.70]
200
[0.80]
225
[0.90]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
15
[530]
20
[706]
25
[883]
27
[953]
Low
Low
Low
Middle
Middle
Middle
High
High
High
Low
Low Low
Middle
Middle Middle
High
High
High
PVA-A30AA4
• Vertical, Horizontal Right, Horizontal Left • Downflow
External static pressure 0.30 [in.WG] (75Pa) 208/230V 60Hz
External static pressure 0.50 [in.WG] (125Pa) 208/230V 60Hz
External static pressure 0.80 [in.WG] (200Pa) 208/230V 60Hz
External static pressure 0.30 [in.WG] (75Pa) 208/230V 60Hz
External static pressure 0.50 [in.WG] (125Pa) 208/230V 60Hz
External static pressure 0.80 [in.WG] (200Pa) 208/230V 60Hz
FAN PERFORMANCE AND CORRECTED AIR FLOW
4
HWE1406A.qx 3/19/15 9:02 AM Page 6

7
0
[0]
25
[0.10]
75
[0.30]
50
[0.20]
100
[0.40]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
20
[706]
25
[883]
30
[1059]
37
[1306]
35
[1236]
20
[706]
25
[883]
30
[1059]
37
[1306]
35
[1236]
20
[706]
25
[883]
30
[1059]
37
[1306]
35
[1236]
25
[0.10]
50
[0.20]
100
[0.40]
75
[0.30]
125
[0.50]
150
[0.60]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
75
[0.30]
100
[0.40]
150
[0.60]
125
[0.50]
175
[0.70]
200
[0.80]
225
[0.90]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
0
[0]
25
[0.10]
75
[0.30]
50
[0.20]
100
[0.40]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
25
[0.10]
50
[0.20]
100
[0.40]
75
[0.30]
125
[0.50]
150
[0.60]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
75
[0.30]
100
[0.40]
150
[0.60]
125
[0.50]
175
[0.70]
200
[0.80]
225
[0.90]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
20
[706]
25
[883]
30
[1059]
37
[1306]
35
[1236]
20
[706]
25
[883]
30
[1059]
37
[1306]
35
[1236]
20
[706]
25
[883]
30
[1059]
37
[1306]
35
[1236]
Low Low
Low
Middle Middle
Middle
High
High
High
Low
Low Low
Middle
Middle Middle
High
High High
PVA-A36AA4
• Vertical, Horizontal Right, Horizontal Left • Downflow
External static pressure 0.30 [in.WG] (75Pa) 208/230V 60Hz
External static pressure 0.50 [in.WG] (125Pa) 208/230V 60Hz
External static pressure 0.80 [in.WG] (200Pa) 208/230V 60Hz
External static pressure 0.30 [in.WG] (75Pa) 208/230V 60Hz
External static pressure 0.50 [in.WG] (125Pa) 208/230V 60Hz
External static pressure 0.80 [in.WG] (200Pa) 208/230V 60Hz
HWE1406A.qx 3/19/15 9:02 AM Page 7

8
0
[0]
25
[0.10]
75
[0.30]
50
[0.20]
100
[0.40]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
26
[918]
30
[1059]
35
[1236]
47
[1660]
45
[1589]
40
[1412]
26
[918]
30
[1059]
35
[1236]
43
[1518]
40
[1412]
26
[918]
30
[1059]
35
[1236]
44
[1554]
40
[1412]
50
[0.20]
100
[0.40]
75
[0.30]
125
[0.50]
150
[0.60]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
75
[0.30]
100
[0.40]
150
[0.60]
125
[0.50]
175
[0.70]
200
[0.80]
225
[0.90]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
0
[0]
25
[0.10]
75
[0.30]
50
[0.20]
125
[0.50]
100
[0.40]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
50
[0.20]
75
[0.30]
125
[0.50]
100
[0.40]
150
[0.60]
175
[0.70]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
75
[0.30]
100
[0.40]
150
[0.60]
125
[0.50]
175
[0.70]
200
[0.80]
225
[0.90]
Airflow rate (m3/min)[cfm]
Static pressure (Pa)[in.WG]
26
[918]
30
[1059]
35
[1236]
43
[1518]
40
[1412]
26
[918]
30
[1059]
35
[1236]
43
[1518]
40
[1412]
26
[918]
30
[1059]
35
[1236]
43
[1518]
40
[1412]
Low Low
Low
Middle Middle
Middle
High
High
High
Low
Low
Low
Middle
Middle
Middle
High
High
High
PVA-A42AA4
• Vertical, Horizontal Right, Horizontal Left • Downflow
External static pressure 0.30 [in.WG] (75Pa) 208/230V 60Hz
External static pressure 0.50 [in.WG] (125Pa) 208/230V 60Hz
External static pressure 0.70 [in.WG] (175Pa) 208/230V 60Hz
External static pressure 0.30 [in.WG] (75Pa) 208/230V 60Hz
External static pressure 0.50 [in.WG] (125Pa) 208/230V 60Hz
External static pressure 0.80 [in.WG] (200Pa) 208/230V 60Hz
HWE1406A.qx 3/19/15 9:02 AM Page 8