Mitsubishi Electric LAN CONTROL UTILITY User manual

LAN Control Utility
User Manual
Contents
1. Introduction ............................................................................................................ 2
1.1. Preparing to use network features .......................................................................................... 2
1.2. Functions and features ............................................................................................................ 2
1.3. Operation environment ............................................................................................................ 2
2. Setup...................................................................................................................... 4
2.1. Installation of “ProjectorView Global+”.................................................................................... 4
2.2. When deleting “ProjectorView Global+” (Uninstallation) ......................................................... 5
3. Main screen............................................................................................................ 6
3.1. System settings ....................................................................................................................... 8
4. Projector registration .............................................................................................. 9
4.1. Connection............................................................................................................................... 9
4.2. Registration of projector to “ProjectorView Global+”.............................................................11
4.3. When changing the projector IP settings .............................................................................. 13
4.4. When changing projector settings......................................................................................... 14
4.5. When deleting projector registration ..................................................................................... 14
5. Operation of projector .......................................................................................... 15
5.1. Operation of projector by remote controller .......................................................................... 15
5.2. Confirmation of projector status............................................................................................ 16
6. Schedule setting................................................................................................... 17
6.1. Creation of projector group ................................................................................................... 17
6.2. When changing schedule setting .......................................................................................... 18
6.3. When deleting group.............................................................................................................. 19
7. E-mail setting........................................................................................................ 20
7.1. Connection with E-mail server............................................................................................... 20
7.2. E-mail setting ......................................................................................................................... 20
7.3. Sending test E-mail................................................................................................................ 20
8. Visual PA2 (Visual PA2 enabled projectors only).................................................. 21
8.1. Starting Visual PA2 ................................................................................................................ 21
8.2. Saving messages entered and settings specified in Visual PA2........................................... 22
8.3. Loading saved data in Visual PA2 ......................................................................................... 22
8.4. Deleting data from Visual PA2 ............................................................................................... 22
8.5. Configuring the Schedule function of Visual PA2.................................................................. 23
9. ProjectorView (ProjectorView enabled projectors only)........................................ 24
9.1. Starting ProjectorView ........................................................................................................... 24
10.Telnet setup (Telnet enabled projectors only)....................................................... 25
10.1. Displaying the Telnet setting screen...................................................................................... 25
11. Web UI (RoomView Connected projectors only) .................................................. 26
11.1. Main functions ....................................................................................................................... 26
11.2. Starting Web UI...................................................................................................................... 26
12.Others................................................................................................................... 30
12.1. Troubleshooting ..................................................................................................................... 30
12.2.Supported projectors............................................................................................................. 30

EN-2
1.1. Preparing to use network features
This projector is equipped with the network function.
Before using the network function, perform the following 2 preparation steps.
• Installing the ProjectorView Global+
• Configuring the projector IP address, network password, and network certification settings
The projector IP address, network password, and network certification settings can be configured in the projector
menu. For more information, see the section describing network settings provided in the projector’s User Manual.
<Note>
• It is recommended that you assign an IP address of the projector to the fixed IP address and set DHCP
Function to Off.
• Set the IP addresses, subnet masks, and default gateways of the projectors and computer correctly. For
details, contact your network administrator.
• Be sure to make a note of the IP addresses and default gateways you set. If you forget the setting values, you
may not be able to detect the projectors again.
1.2. Functions and features
ProjectorView Global+
• 200 units of projectors can be remote-controlled at the maximum.
• Settings such as the IP address of the projector can be configured.
• You can register multiple projectors in a group and control them collectively.
• Various conditions of connected projectors can be monitored.
• Schedule of the power supply ON/OFF can be set every group.
• Schedule of the power supply ON/OFF can be set every day.
• When the communication with the projector monitored by the theft detector is disrupted, warning E-mail is
issued to the designated address.
• Message can be displayed on the screen of the operating projector. (Visual PA2 enabled projectors only)
• The projector is capable of reading aloud on-screen messages. (Text Speech enabled projectors only)
Web UI
• Each projector can be controlled and monitored separately using a Web browser.
• When an error or warning occurs with the projector, you can check its details.
1.3. Operation environment
• Supported OS
Windows XP, Windows Vista and Windows 7 (Operation on a 64bit version of any operating system isn't
guaranteed.)
• CPU
Higher than the minimum specifications for the above operating systems to work
• Memory
More than the minimum specifications for the above operating systems to work
• Free HDD space
32 MB or more (recommended)
• Web browser (When using Web UI)
Internet Explorer Ver. 8.0 and Ver. 9.0 (recommended)
(To use this function, install Adobe Flash Player on your computer. Download Adobe Flash Player from the
website of Adobe Systems Incorporated.)
1. Introduction

EN-3
Microsoft®and Windows®are the registered trademark or trademark of Microsoft Corporation in the United
States and other countries.
(The official name of Windows is Microsoft Windows Operating System.)
Adobe, Flash, and Adobe Flash Player are trademarks or registered trademarks of Adobe Systems Incorporated.
Crestron, RoomView, Crestron RoomView and RoomView Connected are registered trademarks of Crestron
Electronics, Inc.
Other company names and product names described in this document are the registered trademark or trademark
of the respective holders.
Furthermore, “®” mark and “TM” mark are omitted in this document.
• Windows XP is referred to as Microsoft Windows XP Home Edition/Professional.
• Windows Vista is referred to as Microsoft Windows Vista Home Basic/Home Premium/Business/Enterprise/
Ultimate.
• Windows 7 is referred to as Microsoft Windows 7 Home Basic/Home Premium/Professional/Enterprise/
Ultimate.
1. Introduction

EN-4
2.1. Installation of “ProjectorView Global+”
Before starting installation, be sure to read “ReadMe.txt” contained in the CD-ROM.
Copy “ProjectorView Global+v3_3.msi” contained in the Tools folder of CD-ROM to the hard disk of your
personal computer.
(1) Double click “ProjectorView Global+v3_3.msi”, and start up the installer of “ProjectorView
Global+”.
(2) The setup window is displayed. Click [Next].
(3) Select the folder to be installed, and click [Next].
<Note>
• When installing “ProjectorView Global+” to Windows Vista or Windows 7, do not change the installation
destination folder.
(4) Click [Next].
• Installation is started.
2. Setup

EN-5
(5) When the installation has been completed, click [Close].
2.2. When deleting “ProjectorView Global+” (Uninstallation)
<Note>
• When uninstalling “ProjectorView Global+”, “ProjectorView Global+” should be ended in advance. If the
application continues operating, uninstallation can not be performed normally.
(1) Double click “ProjectorView Global+v3_3.msi”, and start up the installer of “ProjectorView
Global+”.
(2) Select “Remove ProjectorView Global+”, and click [Finish].
• The uninstallation is started.
(3) When the uninstallation has been completed, click [Close].
• Logs and setting files are not automatically deleted. Delete them manually.
2. Setup

EN-6
Menu bar
Configuration You can specify the following settings:
Add New Group: You can create a new group.
Edit Schedule Setting: You can edit schedule settings set for existing groups.
Search Projector: Automatically searches available projectors.
Assign IP: You can configure IP settings of the projector.
Edit Projector Setting: You can edit projector settings.
Edit E-mail Setting: You can configure E-mail settings used for this application.
Search Projector Setting: You can specify a search range for communication with the projector via a
router.
System Configuration: You can configure system settings of this application.
Help The version information is displayed.
Tool bar
ProjectorView You can control each projector separately using a Web browser. (ProjectorView
enabled projectors only.) In case of an error in the projector, the details of the error
are displayed. For details, see page 24.
Telnet You can make various settings using Telnet. (Telnet enabled projectors only.) You
can set the password, ProjectorView display language, LAN control, and PJLink
certification. For details, see page 25.
Visual PA2 You can display a line of any text on the projector screen (Visual PA2 enabled
projectors only). For details, see page 21.
Remote Controller Remote Controller window can be displayed to operate the projector. You can turn
on/off the power, and select the input source.
Refresh Status The current status of Power, Input Source, AV Mute, and Lamp Time 1/2 (Low) of the
projectors being displayed in the projector list can be reacquired. The status of Input
Source and AV Mute will not be obtained under the following conditions:
• when the projector is powered off
• during warm-up or cool-down.
Select All All projectors currently displayed on the projector list can be set to selected/non
selected state.
Exit You can exit “ProjectorView Global+”. However, you cannot exit the application
during the automatic projector search and the projector status refreshing. Even
during the projector status acquisition, you can exit the application forcefully by
clicking the button at the upper right corner of the main screen. In this case,
Windows warning message is displayed.
3. Main screen







EN-7
3. Main screen
Group Name Group of the projector can be selected. When you select “All”, all the registered
projectors are displayed. Newly created group(s) are added to the list. When you
select your choice of group, all projectors that belong to the selected group are
displayed.
Status tag Property and status of the projector can be indicated. When clicking each tag button
(except the MAC address), the list can be rearranged (sorted).
Projector list display column
List of the projector which belongs to the selected group can be displayed. Status of
the projector can also be displayed. The display color changes as follows depending
on the condition of the projector:
Black: In normal condition
Red: In abnormal condition (Check the abnormal condition by ProjectorView
or Web UI. When the communication fails, see “12.1. Troubleshooting.”)
Black (yellow background): Warning about the lamp lifetime
White (red background): The communication with the projector monitored by the theft detector has
been disrupted. (Check the condition. There is a possibility of theft.)
Gray: In communication inoperable condition
Error Message Error messages detected in communicating with the projector can be displayed.
Operation status display column
Operation status of “ProjectorView Global+” can be indicated. Operation status
during communication processing by remote-controlling and schedule can be
indicated.

EN-8
3. Main screen
3.1. System settings
(1) Select “System Configuration” from “Configuration” of the menu bar on the main screen.
• “System Configuration” window is displayed. (Default settings are shown in the following example.)
Item Description
Language You can select the user interface language, Japanese or English.
Refresh Status Cycle You can set the cycle to obtain the projector status. Select an integer value with
no decimal part from 1 to 60 minutes.
(2) Change the settings as needed and click [Save].
• To update the settings you changed, it is necessary to restart “ProjectorView Global+”.

EN-9
4. Projector registration
4.1. Connection
Connect the controller computer and the projector, which have installed “ProjectorView Global+”, to a
commercially available LAN cable or wireless LAN adapter.
When connecting multiple projectors, use a commercially available ethernet hub.
• A LAN terminal or 802.11b/g/n wireless LAN adapter is required for the controller computer.
• Use a LAN cable compatible with Category 5 and 100BASE-T.
Both crossover and straight-through cables can be used.
(In the case of connection examples 5 and 6, see the instruction manual of the router.)
<Note>
• The LAN function may be unavailable depending on the standby mode setting of the projector. To enable the
LAN function, change the setting referring to the User Manual of your projector.
• Some USB wireless adapters cannot be used for your projector depending on the specifications.
Connection example 1
Controller computer
Projector
Commercially available LAN cable
Projector
Projector
Connection example 2
Controller computer
Connection example 3
Controller computer
External
ethernet hub Commercially available LAN cable

EN-10
4. Projector registration
External
ethernet hub
External
ethernet hub
External
ethernet hub
External
ethernet hub
Projector
Projector
External
ethernet hub
Router
Router
Projector
Projector
Projector
Projector
Projector
Connection example 4
Connection example 5
Connection example 6
Controller computer
Controller computer
Controller computer
Commercially
available LAN cable

EN-11
4. Projector registration
4.2. Registration of projector to “ProjectorView Global+”
The procedures to register projectors vary among the foregoing connection examples.
• In connection examples 1 to 4 (where projectors are installed within the same local network), the projectors
within such network are automatically detected and registered. For details, see procedure A below.
• In connection examples 5 and 6 (where projectors are installed via a router), specify the range of the
projectors’ IP addresses and then carry out automatic projector search within the range to register projectors.
For details, see procedure B below.
• Up to 200 units of projectors can be registered at the maximum.
• Projectors that have just been registered by the automatic projector search aren’t belonging to any group.
When the projectors you registered aren’t displayed on the projector list on the main screen, select “All” from
the group select pull-down menu.
Procedure A - For connection examples 1 to 4 (where projectors are installed within the
same local network)
(1) Start up “ProjectorView Global+”.
(2) Select “Search Projector” from “Configuration” of the menu bar on the main screen.
• The projectors connected to LAN are searched automatically.
• Some projectors may require you to enter the password when establishing projector connections for the first
time. If the projector password is changed, you need to enter that new password.
<Note>
• Note that a different IP address may be assigned every time you start the projectors. If a connection cannot
be established, execute “Search Projector”.
• If you change the IP address in the projector menu after the projectors have been detected, execute “Search
Projector” again.
• If several projectors with the same IP address are registered, delete the ones which are not connected to the
network from “Edit Projector Setting”.
• Ensure that the IP address of the computer and that of the projector are in the same network group. (The last
octet of the IP address should contain a different value.)
• Be sure to make a note of the IP addresses you set. If you forget the IP addresses, you may not be able to
detect the projectors again.
• It is recommended that you assign an IP address of the projector to the fixed IP address.

EN-12
4. Projector registration
Procedure B - Connection examples 5 and 6 (where projectors are installed via a router)
To automatically detect projectors connected via a router, specify a range of IP addresses to search that
particular IP address using “Search Projector Setting”.
(1) Start up “ProjectorView Global+”.
(2) Select “Search Projector Setting” from “Configuration” of the menu bar.
• “Search Projector Setting” window is displayed.


Item Description
Start IP Address Specify the IP address that is the start of the search range.
(You cannot specify an IP address that contains a range other than 1 to 254 for
the first and last octets and a range other than 0 to 255 for the second and third
octets.)
End IP Address Specify the last octet of the IP address that is the end of the search range. (You
cannot specify a value that contains a number other than 1 to 254. In addition,
you cannot specify a value that is smaller than the last octet of the search start IP
address specified in step .)
Search Projector The settings you made are saved and then the automatic projector search is
performed.
(3) Specify the projector search range by IP address (and ).
• Up to 16 search ranges can be set. (Settings can be configured for each line of the search range.)
(4) To save the settings, click [Save]. To continue the projector search, click [Search Projector].
• When you click [Save], the search ranges you specify are saved and the “Search Projector Setting” window
is closed.
• When you don’t want to save the search ranges, click [Cancel] to close the “Search Projector Setting”
window.
• After saving the settings, by selecting “Configuration” on the menu bar and then selecting “Search
Projector”, you can perform automatic projector search within the search ranges you saved.
• Some projectors may require you to enter the password when establishing projector connections for the
first time. Authentication is automatically performed from the second time onwards unless projectors are
deleted from the list.

EN-13
4. Projector registration
<Note>
• If you want to connect a projector via a router after automatically detecting it, you need to specify a search
range of IP addresses that includes the projector’s IP address in advance.
• Note that a different IP address may be assigned every time you start the projectors. If a connection cannot
be established, specify the projector search range and execute “Search Projector” again.
• If you change the IP address in the projector menu after the projectors have been detected, execute “Search
Projector” again.
• If several projectors with the same IP address are registered, delete the ones which are not connected to the
network from “Edit Projector Setting”.
4.3. When changing the projector IP settings
You can change the projector IP settings.
(1) Select the projector which you like to change from the projector list on the main screen.
(2) Select "Assign IP" from “Configuration” of the menu bar on the main screen.
• “Assign IP” window is displayed.
(3) To automatically assign an IP address, select [Auto] and then select DHCP. To manually
assign an IP address, select [Manual] and enter values for IP Address, Subnet Mask, and
Default Gateway.
Item Description
DHCP Obtain an IP address via a DHCP server.
IP Address Enter an IP address.
Subnet Mask Enter the subnet mask.
Default Gateway Enter the default gateway address.
<Note>
• Even when you change the projector IP settings in the “Assign IP” window, settings of DHCP Function, Start
IP Address, and End IP Address in the projector menu are not changed.
• An error dialog for theft detection may be displayed after the IP settings have been changed.
• If a connection cannot be established after the IP settings have been changed, execute “Search Projector”.

EN-14
4. Projector registration
4.4. When changing projector settings
(1) Select the projector which you like to change from the projector list on the main screen.
(2) Select “Edit Projector Setting” from “Configuration” of the menu bar.
• “Edit Projector Setting” window is displayed.
(3) Set the Projector Name and its group and the theft detector.
Item Description
Projector Name Enter the projector name within 64 characters in one-byte alphanumeric symbol.
MAC Address The MAC address is displayed. The displayed address cannot be changed.
IP Address The IP address is displayed. The displayed address cannot be changed. When it
is required to change the IP address, use [Assign IP].
Group Name From the pull-down menu, select the group to which the projector is belonging.
(A new group can be created by clicking [Add New Group]. See “6.1. Creation
of projector group”.)
Theft Check Turn on or off the theft detector.
<Note>
In right-click menu also, the setting of the projector can be changed. (Multiple projectors can be selected.)
• Add to New Group : Addition to a newly created group
• Add to Existing Group : Change of the belonging group
• Theft Check Setting : Change of theft detector setting (ON/OFF)
4.5. When deleting projector registration
(1) Select the projector which you like to delete from the projector list on the main screen.
(2) Select “Edit Projector Setting” from “Configuration” of the menu bar.
• “Edit Projector Setting” window is displayed.
(3) Click [Delete].
• The selected projector is deleted.

EN-15
5. Operation of projector
5.1. Operation of projector by remote controller
Group or single unit of projector can be operated.
(1) Select the projector which you like to operate from the projector list on the main screen.
• When selecting more than one projector simultaneously, select while pressing the Ctrl key.
(2) Click [Remote Controller] of the tool bar on the main screen or when you like to operate a
certain projector, double click the projector on the projector list on the main screen.
• “Remote Controller” window is displayed.
(3) Operate the projector by selecting each operating button on the window.
Command Button Description
Power Power ON Turn on the power supply of the projector.
Power OFF Turn off the power supply of the projector.
Input Source COMPUTER 1 Change the input signal to COMPUTER 1.
COMPUTER 2 Change the input signal to COMPUTER 2.
VIDEO Change the input signal to VIDEO.
S-VIDEO Change the input signal to S-VIDEO.
COMPONENT Change the input signal to COMPONENT.
DIGITAL 1 *1Change the input signal to DIGITAL 1 *1.
DIGITAL 2 *1Change the input signal to DIGITAL 2 *1.
DIGITAL 3 *1Change the input signal to DIGITAL 3 *1.
STORAGE 1 *2Change the input signal to USB VIEWER *2.
STORAGE 2 Change the input signal to USB Display.
NETWORK Change the input signal to LAN Display.
Exit Close the Remote Controller window.
*1DIGITAL 1-3 are displayed with HDMI (HDMI 1/HDMI 2), DVI-D or SDI by a connected projector.
*2STORAGE 1 is displayed with PC Less Presentation or USB Viewer by a connected projector.
<Note>
• The next operation can not be performed until the previous operation has been completed.
• The operation can not be performed during re-obtaining (refreshing) the projector status.
• Available input sources vary depending on the type of projectors. You cannot select input sources that aren’t
supported by the projector.

EN-16
5. Operation of projector
5.2. Confirmation of projector status
The status of the projector is displayed on the projector list on the main screen.
Item Description
Check Theft detector setting (ON/OFF)
No. Projector list registration number
Projector Name Projector name set in the application
MAC Address MAC address of the projector
IP Address IP address of the projector
Power Power supply status of the projector (ON/OFF)
Input Source *1Input signal of the projector (COMPUTER 1/COMPUTER 2/VIDEO/S-VIDEO/HDMI
(HDMI1/HDMI2)/DVI-D/SDI/USB Viewer/PC Less Presentation/USB Display/LAN
Display/COMPONENT)
AV Mute Mute status of the projector (ON/OFF)
Lamp 1/2 Time (Low) Lamp illuminating time (HHHH:MM or HHHHH:MM)
In the case of the projector equipped with two lamps, illuminating time for
the lamp 1 is displayed in the left side and illuminating time for the lamp 2 is
displayed in the right side. For the lamp-free projectors, light source usage
time is displayed instead of lamp times. In this case, the time is not Low-mode
equivalent time but actual usage time.
Group Name The belonging group of projector
*1HDMI and DVI-D are displayed with DIGITAL 1 or DIGITAL 2 by a connected projector.
• The projector status is re-obtained (refreshed) automatically and periodically, but the present status can
also be obtained by the user’s instruction. When clicking [Refresh Status] of the tool bar on the main screen,
Power, Input Source, AV Mute, and Lamp 1/2 Time (Low) status of each projector is re-obtained.
• The status of Input Source and AV Mute will not be obtained under the following conditions:
- when the projector is powered off
- during warm-up or cool-down.
• When clicking the status tag of the projector list (except the MAC address), the list can be rearranged (sorted).
The list can be rearranged in reversed order by pressing one more time.
• When clicking [Select All] of the tool bar, all projectors in the projector list become selected/non selected
state.
• If any abnormal state of the projector is detected by acquiring the projector status, an error message will be
displayed on the error message display column at the lower part of the screen.
<Note>
• The default cycle of the automatic re-acquisition is 10 minutes. To change this cycle, see “3.1. System
settings.”
• When multiple projectors are connected, it may take time to acquire the status. During acquiring the status,
the status bar at the lower part of the main screen becomes “Getting status...”, and it becomes “Done” when
the acquisition has been completed.

EN-17
6. Schedule setting
6.1. Creation of projector group
Multiple projectors can be controlled and batched by sorting groups.
Also, each group can set each time of the power supply ON/OFF every day.
Since the schedule of the power supply ON/OFF is performed by each group, the projector which you like to
operate at the same schedule should be integrated into the same group.
When Power ON and Power OFF are enabled, their time settings are indicated on the schedule list.
[Example] When setting the schedule for the group “group 1” to turn the power supply ON at 8:00 on Monday,
turning OFF at 18:00 on the same day, ON at 8:40 on Thursday, and OFF at 17:00 on Friday.
Time of power supply ON/OFF
Group name
Day of the week
Time of power supply ON
Time of power supply OFF
When validating the setting,
put a check mark in the box.
Schedule list
(1) Select “Add New Group” from “Configuration” of the menu bar.
• “Add New Group” window is displayed.
(2) Input the group name to be created in the “Group Name” column (within 16 characters in
one-byte alphanumeric symbol).
(3) Select the day of the week to be set for the time of the power supply ON/OFF.
(4) Only when setting the time of the power supply ON, set the time in the “Power ON” column,
and put a check mark in the “Enable” box.
(5) Only when setting the time of power supply OFF, set the time in the “Power OFF” column,
and put a check mark in the “Enable” box.
(6) When there are more than one day of the week to be set for the power supply ON/OFF
schedule, repeat the procedure (3) to (5).
(7)Click [Add].

EN-18
6. Schedule setting
<Note>
• The power supply ON and the power supply OFF can not be selected at the same time of the same day of the
week.
• The Schedule Setting will be executed while “ProjectorView Global+” is in operation.
• Depending on usage conditions, such as when there are so many projectors that you need to control, the time
to be executed by the power supply control may deviate from the setting time of the schedule.
• When utilizing the Network Time Protocol (NTP) function on the Internet, the schedule operation may not be
executed because the setting time of the schedule jumps over.
• When the automatic time adjustment by summer time is valid, the schedule operation may not be executed
because the time is automatically adjusted before and after switching over.
6.2. When changing schedule setting
(1) Select a group which you like to change from the Group select pull-down menu on the main
screen.
(2) Select “Edit Schedule Setting” from “Configuration” of the menu bar.
• “Edit Schedule Setting” window is displayed.
(3) Change the contents which you like to correct, and click [Save].
• Corrected contents are reflected.

EN-19
6. Schedule setting
6.3. When deleting group
(1) Select the group which you like to delete from the Group select pull-down menu on the main
screen.
(2) Select “Edit Schedule Setting” from “Configuration” of the menu bar.
• “Edit Schedule Setting” window is displayed.
(3) Click [Delete].
• The selected group is deleted.
<Note>
• When deleting a group, the projector which has belonged to the relevant group will not belong to any group.
Set a new group to belong again on “Edit Projector Setting” window.

EN-20
7. E-mail setting
When the communication with the projector monitored by the theft detector is disrupted, a warning E-mail can be
sent to the designated address, enabling to serve for early detection of the projector theft.
The E-mail setting can not be set at every projector and every group. The same setting should be set for all
projectors.
7.1. Connection with E-mail server
Connect the E-mail server to the network to which the controller computer and the projector are connected that
“ProjectorView Global+” is operating.
7. 2 . E- ma il set t in g
Designate the address of the E-mail server and the address of the destination to be sent.
<Note>
• As for the network environment, confirm to the network administrator.
(1) Select “Edit E-mail Setting” from “Configuration” of the menu bar on the main screen.
• “Edit E-mail Setting” window is displayed.
(2) Input the setting item for the network environment, and click [Save].
Item Description
E-mail Server (SMTP) Enter the IP address of the E-mail server (Example: 192.168.7.230), or
input the server name (Example: mail.example.com).
Destination E-mail Address Enter the destination E-mail address using up to 64 single-byte
characters. (Up to 3 places can be designated at the maximum.)
7.3. Sending test E-mail
After completing the setting of the each item on the E-mail Setting window, a test E-mail can be sent to confirm
whether the E-mail is correctly delivered to the destination. When clicking [Test E-mail] at the upper right on
the Email Setting window, the test E-mail is issued. Confirm whether the E-mail is correctly delivered to the
destination address.
<Note>
• The E-mail function will be executed while “ProjectorView Global+” is in operation.
• If the test E-mail is not correctly received, confirm the address of the E-mail server and the destination, and
the connection status of the network. For details, make an inquiry to the network administrator.
• The E-mail may possibly not be delivered depending on the certification function of the E-mail server. For
details, make an inquiry to the network administrator.
• When the communication with the projector monitored by the theft detector is disrupted, a theft check error
dialog is displayed.
However, the projector list isn’t updated at the same time because it takes some time to update the list.