Mitsubishi Electric PJLink FD630U User manual

LAN Control Utility
User Manual
Contents
1. Introduction ............................................................................................... 2
1.1. Preparing to use network features.......................................................................... 2
1.2. Functions and features ........................................................................................... 2
1.3. Operation environment ........................................................................................... 2
2. Setup......................................................................................................... 4
2.1. Installation of "ProjectorView Global+" ................................................................... 4
2.2. When deleting "ProjectorView Global+" (Uninstallation)......................................... 5
2.3. Connection.............................................................................................................. 6
3. Main screen............................................................................................... 7
3.1. System settings ...................................................................................................... 9
4. Projector registration ............................................................................... 10
4.1. Registration of projector to "ProjectorView Global+" ............................................ 10
4.2. When changing the projector IP settings .............................................................. 12
4.3. When changing projector settings ........................................................................ 13
4.4. When deleting projector registration ..................................................................... 13
5. Operation of projector.............................................................................. 14
5.1. Operation of projector by remote controller .......................................................... 14
5.2. Confirmation of projector status............................................................................ 15
6. Schedule setting...................................................................................... 16
6.1. Creation of projector group ................................................................................... 16
6.2. When changing schedule setting.......................................................................... 17
6.3. When deleting group............................................................................................. 18
7. E-mail setting........................................................................................... 19
7.1. Connection with E-mail server .............................................................................. 19
7.2. E-mail setting ........................................................................................................ 19
7.3. Sending test E-mail............................................................................................... 19
8. ProjectorView .......................................................................................... 20
8.1. Main functions....................................................................................................... 20
8.2. Starting ProjectorView .......................................................................................... 20
8.3. Entering projector information............................................................................... 22
8.4. Setting the network password............................................................................... 23
8.5. Resetting the network settings.............................................................................. 24
9. Visual PA2 (Visual PA2 enabled projectors only).................................... 25
9.1. Starting Visual PA2............................................................................................... 25
9.2. Saving messages entered and settings specified in Visual PA2 .......................... 26
9.3. Loading saved data in Visual PA2 ........................................................................ 26
9.4. Deleting data from Visual PA2.............................................................................. 26
9.5. Configuring the Schedule function of Visual PA2 ................................................. 27
10. Telnet setup (Telnet enabled projectors only)......................................... 28
11. PJLink ..................................................................................................... 29
11.1. About PJLink......................................................................................................... 29
12. Others ..................................................................................................... 30
12.1. Troubleshooting .................................................................................................... 30
12.2. Supported Projectors ............................................................................................ 30

2
1. Introduction
1.1. Preparing to use network features
• Installing the ProjectorView Global+
• Assigning the projector IP address
• Configuring settings such as PASSWORD, E-mail Setting, Language, and PJLink Certification Setting by running
Telnet (Telnet enabled projectors only) or using ProjectorView
The projector IP address, password, and PJLink certification can be configured on the projector main screen. For
more information, see the section describing network settings provided in the projector's User Manual.
1.2. Functions and features
ProjectorView Global+
• 200 units of projectors can be remote-controlled at the maximum.
• Settings such as the IP address of the projector can be configured.
• You can register multiple projectors in a group and control them collectively.
• Various conditions of connected projectors can be monitored.
• Schedule of the power supply ON/OFF can be set every group.
• Schedule of the power supply ON/OFF can be set every day.
• When the communication with the projector monitored by the theft detector is disrupted, warning E-mail is issued
to the designated address.
• Message can be displayed on the screen of the operating projector. (Visual PA2 enabled projectors only)
• The projector is capable of reading aloud on-screen messages. (Text Speech enabled projectors only)
ProjectorView
• Each projector can be controlled separately using a Web browser.
• When an error or warning occurs with the projector, warning E-mail is issued to the designated address.
PJLink
• The product supports the industry standard protocol PJLink for projector control.
1.3. Operation environment
• Supported OS
Windows XP, Windows Vista
•CPU
Pentium II 233 MHz or higher (recommended)
•Memory
128 MB or more (recommended)
• Free HDD space
32 MB or more (recommended)
• Web browser (When using ProjectorView)
Internet Explorer Ver. 6.0 and Ver. 7.0 (recommended)
(Java Plug-in *1 must be installed and JavaScript must be enabled.)
*1 Installing Java Plug-in:
(1) Download JRE6 from the JAVA download center on the Sun Microsystems Web site
(http://java.sun.com/javase/downloads/index.jsp).
(When this file URL is not a valid location, search for "JRE6 download" using a search engine and access the
download site.)
(2) Execute the downloaded file.
(3) After installation is complete, disable the cache settings as following procedures.
1. Select [Start] - [Control Panel] - [Java].
2. Select [General] tab and click [Settings...].
3. Click [Delete Files...].
4. Click [OK] in the Delete Temporary Files window.

3
1. Introduction
Microsoft®and Windows®are the registered trademark or trademark of Microsoft Corporation in the United States
and other countries.
(The official name of Windows is Microsoft Windows Operating System.)
Pentium is the trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and
other countries.
The trademark of PJLink is trademark applied for registration or registered trademark of Japan Business Machine
and Information System Industries Association (JBMIA) in Japan, the United States, and other countries and areas.
Other company names and product names described in this document are the registered trademark or trademark of
the respective holders.
Furthermore, "®" mark and "TM" mark are omitted in this document.
• Windows XP is referred to as Microsoft Windows XP Home Edition/Professional.
• Windows Vista is referred to as Microsoft Windows Vista Home Basic/Home Premium/Business/Enterprise/
Ultimate.

4
2. Setup
2.1. Installation of "ProjectorView Global+"
Before starting installation, be sure to read "ReadMe.txt" contained in the CD-ROM.
Copy ProjectorView Global+v2.msi contained in the Tools folder of CD-ROM to the hard disk of your personal
computer.
(1) Double click "ProjectorView Global+v2.msi", and start up the installer of "ProjectorView
Global+".
(2) The setup window is displayed. Click [Next].
(3) Select the folder to be installed, and click [Next].
<Note>
• When installing "ProjectorView Global+" to Windows Vista, do not change the installation destination folder.
(4) Click [Next].
• Installation is started.

5
2. Setup
(5) When the installation has been completed, click [Close].
2.2. When deleting "ProjectorView Global+" (Uninstallation)
<Note>
• When uninstalling "ProjectorView Global+", "ProjectorView Global+" should be ended in advance. If the
application continues operating, uninstallation can not be performed normally.
(1) Double click "ProjectorView Global+v2.msi", and start up the installer of "ProjectorView
Global+".
(2) Select "Remove ProjectorView Global+", and click [Finish].
• The uninstallation is started.
(3) When the uninstallation has been completed, click [Close].
• Logs and setting files are not automatically deleted. Delete them manually.

6
2. Setup
2.3. Connection
Connect the controller PC and the projector, which have installed "ProjectorView Global+", to a commercially
available LAN cable.
When connecting multiple projectors, use a commercially available hub.
• A LAN terminal is required for the controller PC.
• Use a LAN cable compatible with Category 5 and 100BASE-T.
Use a crossover LAN cable in the case of connection example 1 and use a straight-through LAN cable in the case
of connection example 2.
(In the case of connection example 3, see the instruction manual of the router.)
• Do not touch metal parts of the LAN terminal and LAN cable by hands charged of static electricity. Discharge of
static electricity may cause a failure of the projector.
• Up to 200 units of the projectors can be registered at the maximum.
<Note>
• The LAN function may be unavailable depending on the standby mode setting of the projector. To enable the LAN
function, change the setting referring to the User Manual of your projector.
Connection example 1
Connection example 2
Connection example 3
Controller PC
Commercially available LAN cable
(Crossover cable)
Projector
External hub
Controller PC
Commercially available
LAN cable
(Straight-through cable)
Projector
Router
Controller PC
Projector
External hub
External hub
Projector

7
3. Main screen
AMenu bar Configuration You can specify the following settings:
• Add New Group: You can create a new group.
• Edit Schedule Setting: You can edit schedule settings set for
existing groups.
• Search Projector: Automatically searches available
projectors.
• Assign IP: You can configure IP settings of the
projector.
• Edit Projector Setting: You can edit projector settings.
• Edit E-mail Setting: You can configure E-mail settings used for
this application.
• Search Projector Setting: You can specify a search range for
communication with the projector via a
router.
• System Configuration: You can configure system settings of this
application.
Help The version information is displayed.
BTool bar ProjectorView You can control each projector separately using a Web browser.
In case of an error in the projector, the details of the error are displayed.
For details, see page 20.
Telnet You can make various settings using Telnet. (Telnet enabled projectors
only)
You can set the password, ProjectorView display language, LAN
control, and PJLink certification. For details, see page 28.
Visual PA2 You can display a line of any text on the projector screen (Visual PA2
enabled projectors only).
For details, see page 25.
Remote Controller Remote Controller window can be displayed to operate the projector.
You can turn on/off the power, and select the input source.
Refresh Status The current status of Power, Input Source, AV Mute, and Lamp Time
(Low) of the projectors being displayed in the projector list can be
reacquired. The status of Input Source and AV Mute will not be
obtained under the following conditions:
• when the projector is powered off
• during warm-up or cool-down.
BA
C
E
F
G
D

8
3. Main screen
Select All All projectors currently displayed on the projector list can be set to
selected/non selected state.
Exit You can exit "ProjectorView Global+". However, you cannot exit the
application during the automatic projector search and the projector
status loading. Even during the projector status acquisition, you can
exit the application forcefully by clicking the button at the upper right
corner of the main screen. In this case, Windows warning message is
displayed.
CGroup Name Group of the projector can be selected. When you select "All", all the
registered projectors are displayed. Newly created group(s) are added
to the list. When you select your choice of group, all projectors that
belong to the selected group are displayed.
DStatus tag Property and status of the projector can be indicated.
When clicking each tag button (except the MAC address), the list can
be rearranged (sorted).
EProjector list display column List of the projector which belongs to the selected group can be
displayed.
Status of the projector can also be displayed.
The display color changes as follows depending on the condition of the
projector:
• Black: In normal condition
• Red: In abnormal condition (→Check the abnormal condition by
ProjectorView. When the communication fails, see "12.1.
Troubleshooting.")
• Black (yellow background):
Warning about the lamp lifetime
• White (red background):
The communication with the projector monitored by the
theft detector has been disrupted. (→Check the condition.
There is a possibility of theft.)
• Gray: In communication inoperable condition
FError Message Error messages detected in communicating with the projector can be
displayed.
GOperation status display column Operation status of "ProjectorView Global+" can be indicated.
Operation status during communication processing by remote-
controlling and schedule can be indicated.

9
3. Main screen
3.1. System settings
(1) Select "System Configuration" from "Configuration" of the menu bar on the main screen.
• "System Configuration" window is displayed. (Default settings are shown in the following example.)
(2) Change the settings as needed and click [Save].
• To update the settings you changed, it is necessary to restart "ProjectorView Global+."
Item Description
Language You can select the user interface language, Japanese or English.
Refresh Status Cycle You can set the cycle to obtain the projector status. Select an integer value with no
decimal part from 1 to 60 minutes.

10
4. Projector registration
4.1. Registration of projector to "ProjectorView Global+"
The procedures to register projectors vary among the foregoing connection examples.
• In connection examples 1 and 2 (where projectors are installed within the same local network), the projectors
within such network are automatically detected and registered. For details, see procedure A below.
• In connection example 3 (where projectors are installed via a router), specify the range of the projectors' IP
addresses and then carry out automatic projector search within the range to register projectors. For details, see
procedure B below.
• Up to 200 units of projectors can be registered at the maximum.
• Projectors that have just been registered by the automatic projector search aren't belonging to any group. When
the projectors you registered aren't displayed on the projector list on the main screen, select "All" from the group
select pull-down menu.
Procedure A - For connection examples 1 and 2 (where projectors are installed within the
same local network)
(1) Start up "ProjectorView Global+".
(2) Select "Search Projector" from "Configuration" of the menu bar on the main screen.
• The projectors connected to LAN are searched automatically.
• Some projectors may require you to enter the password when establishing projector connections for the first
time. If the projector password is changed, you need to enter that new password.
<Note>
• Ensure that the IP address of the PC and that of the projector are in the same network group. (The last octet of the
IP address should contain a different value.)
• Be sure to make a note of the IP addresses you set. If you forget the IP addresses, you may not be able to detect
the projectors again.
• At initial setup, DHCP or Auto IP (169.254.0.1 through 169.254.255.254) automatically assigns an IP address.
Note that a different IP address may be assigned every time you start the projectors. If a connection cannot be
established, execute "Search Projector".
• If you change the IP address in the projector menu after the projectors have been detected, execute "Search
Projector" again.
• It is recommended that you assign an IP address of the projector to the fixed IP address.

11
4. Projector registration
Procedure B - Connection example 3 (where projectors are installed via a router)
To automatically detect projectors connected via a router, confirm the IP address in the projector network menu and
specify a range of IP addresses to search that particular IP address using "Search Projector Setting".
<Note>
If you want to connect a projector via a router after automatically detecting it, you need to specify a search range of
IP addresses that includes the projector's IP address in advance.
(1) Start up "ProjectorView Global+".
(2) Select "Search Projector Setting" from "Configuration" of the menu bar.
• "Search Projector Setting" window is displayed.
(3) Specify the projector search range by IP address (Aand B).
• Up to 16 search ranges can be set. (Settings can be configured for each line of the search range.)
(4) To save the settings, click [Save]. To continue the projector search, click [Search Projector].
• When you click [Save], the search ranges you specify are saved and the "Search Projector Setting" window is
closed.
• When you don't want to save the search ranges, click [Cancel] to close the "Search Projector Setting" window.
• After saving the settings, by selecting "Configuration" on the menu bar and then selecting "Search Projector",
you can perform automatic projector search within the search ranges you saved.
• Some projectors may require you to enter the password when establishing projector connections for the first
time. Authentication is automatically performed from the second time onwards unless projectors are deleted
from the list.
Item Description
AStart IP Address Specify the IP address that is the start of the search range.
(You cannot specify an IP address that contains a range other than 1 to 254 for
the first and last octets and a range other than 0 to 255 for the second and third
octets.)
BEnd IP Address Specify the last octet of the IP address that is the end of the search range.
(You cannot specify a value that contains a number other than 1 to 254. In
addition, you cannot specify a value that is smaller than the last octet of the
search start IP address specified in step A.)
CSearch Projector The settings you made are saved and then the automatic projector search is
performed.
C
A B

12
4. Projector registration
<Note>
• Set the default gateways of the projectors and PC correctly. For details, contact your network administrator.
• Be sure to make a note of the IP addresses and default gateways you set. If you forget the setting values, you may
not be able to detect the projectors again.
• At initial setup, DHCP or Auto IP (169.254.0.1 through 169.254.255.254) automatically assigns an IP address.
Note that a different IP address may be assigned every time you start the projectors. If a connection cannot be
established, execute "Search Projector".
• If you change the IP address in the projector menu after the projectors have been detected, execute "Search
Projector" again.
• It is recommended that you assign an IP address of the projector to the fixed IP address.
4.2. When changing the projector IP settings
You can change the projector IP settings.
(1) Select the projector which you like to change from the projector list on the main screen.
(2) Select "Assign IP" from "Configuration" of the menu bar on the main screen.
• "Assign IP" window is displayed.
(3) To automatically assign an IP address, select [Auto] and then select DHCP. To manually assign
an IP address, select [Manual] and enter values for IP Address, Subnet Mask, and Default
Gateway.
<Note>
• An error dialog for theft detection may be displayed after the IP settings have been changed.
• If a connection cannot be established after the IP settings have been changed, execute "Search Projector".
• If you want to change the IP address of a projector connected via a router, you need to specify a search range of
IP addresses that includes the new IP address in "Search Projector Setting".
• Consult your network administrator about the subnet mask and default gateway in advance.
Item Description
DHCP Obtain an IP address via a DHCP server.
IP Address Enter an IP address.
Subnet Mask Enter the subnet mask.
Default Gateway Enter the default gateway address.

13
4. Projector registration
4.3. When changing projector settings
(1) Select the projector which you like to change from the projector list on the main screen.
(2) Select "Edit Projector Setting" from "Configuration" of the menu bar.
• "Edit Projector Setting" window is displayed.
(3) Set the Projector Name and its group and the theft detector.
<Note>
In right-click menu also, the setting of the projector can be changed. (Multiple projectors can be selected.)
• Add to New Group : Addition to a newly created group
• Add to Existing Group : Change of the belonging group
• Theft Check Setting : Change of theft detector setting (ON/OFF)
4.4. When deleting projector registration
(1) Select the projector which you like to delete from the projector list on the main screen.
(2) Select "Edit Projector Setting" from "Configuration" of the menu bar.
• "Edit Projector Setting" window is displayed.
(3) Click [Delete].
• The selected projector is deleted.
Item Description
Projector Name Input the projector name within 64 characters in one-byte alphanumeric symbol.
MAC Address The MAC address is displayed. The displayed address cannot be changed.
IP Address The IP address is displayed. The displayed address cannot be changed. When it
is required to change the IP address, use [Assign IP].
Group Name From the pull-down menu, select the group to which the projector is belonging.
(A new group can be created by clicking [Add New Group]. →See "6.1. Creation
of projector group".)
Theft Check Turn on or off the theft detector.

14
5. Operation of projector
5.1. Operation of projector by remote controller
Group or single unit of projector can be operated.
(1) Select the projector which you like to operate from the projector list on the main screen.
• When selecting more than one projector simultaneously, select while pressing the Ctrl key.
(2) Click [Remote Controller] of the tool bar on the main screen or when you like to operate a
certain projector, double click the projector on the projector list on the main screen.
• "Remote Controller" window is displayed.
(3) Operate the projector by selecting each operating button on the window.
*1 DIGITAL 1 and DIGITAL 2 are HDMI or DVI active. See your projector User Manual for more information.
<Note>
• The next operation can not be performed until the previous operation has been completed.
• The operation can not be performed during re-obtaining (refreshing) the projector status.
• Available input sources vary depending on the type of projectors. You cannot select input sources that aren't
supported by the projector.
Command Button Description
Power Power ON
Power OFF
Turn on the power supply of the projector.
Turn off the power supply of the projector.
Input Source COMPUTER 1
COMPUTER 2
VIDEO
S-VIDEO
DIGITAL 1*1
DIGITAL 2*1
NETWORK
Change the input signal to COMPUTER 1.
Change the input signal to COMPUTER 2.
Change the input signal to VIDEO.
Change the input signal to S-VIDEO.
Change the input signal to DIGITAL 1*1
.
Change the input signal to DIGITAL 2*1
.
Change the input signal to NETWORK.
Exit Close the Remote Controller window.

15
5. Operation of projector
5.2. Confirmation of projector status
The status of the projector is displayed on the projector list on the main screen.
*1 DIGITAL 1 and DIGITAL 2 are enabled in HDMI or DVI. For the details of the functions, see the projector's
User Manual.
• The projector status is re-obtained (refreshed) automatically and periodically, but the present status can also be
obtained by the user's instruction. When clicking [Refresh Status] of the tool bar on the main screen, Power, Input
Source, AV Mute, and Lamp Time (Low) status of each projector is re-obtained.
• The status of Input Source and AV Mute will not be obtained under the following conditions:
- when the projector is powered off
- during warm-up or cool-down.
• When clicking the status tag of the projector list (except the MAC address), the list can be rearranged (sorted).
The list can be rearranged in reversed order by pressing one more time.
• When clicking [Select All] of the tool bar, all projectors in the projector list become selected/non selected state.
• If any abnormal state of the projector is detected by acquiring the projector status, an error message will be
displayed on the error message display column at the lower part of the screen.
<Note>
• The default cycle of the automatic re-acquisition is 10 minutes. To change this cycle, see "3.1. System settings."
• When multiple projectors are connected, it may take time to acquire the status. During acquiring the status, the
status bar at the lower part of the main screen becomes "Getting status...", and it becomes "Done" when the
acquisition has been completed.
Item Description
Check Theft detector setting (ON/OFF)
No. Projector list registration number
Projector Name Projector name set in the application
MAC Address MAC address of the projector
IP Address IP address of the projector
Power Power supply status of the projector (ON/OFF)
Input Source Input signal of the projector (COMPUTER 1/COMPUTER 2/VIDEO/S-VIDEO/
DIGITAL 1*1/DIGITAL 2*1/NETWORK)
AV Mute Mute status of the projector (ON/OFF)
Lamp Time (Low) Lamp illuminating time (HHHH:MM)
Group Name The belonging group of projector

16
6. Schedule setting
6.1. Creation of projector group
Multiple projectors can be controlled and batched by sorting groups.
Also, each group can set each time of the power supply ON/OFF every day.
Since the schedule of the power supply ON/OFF is performed by each group, the projector which you like to
operate at the same schedule should be integrated into the same group.
When Power ON and Power OFF are enabled, their time settings are indicated on the schedule list.
[Example] When setting the schedule for the group "group 1" to turn the power supply ON at 9:00 on Monday,
turning OFF at 17:00 on the same day, ON at 8:30 on Thursday, and OFF at 17:40 on Friday.
(1) Select "Add New Group" from "Configuration" of the menu bar.
• "Add New Group" window is displayed.
(2) Input the group name to be created in the "Group Name" column (within 16 characters in one-
byte alphanumeric symbol).
(3) Select the day of the week to be set for the time of the power supply ON/OFF.
(4) Only when setting the time of the power supply ON, set the time in the "Power ON" column, and
put a check mark in the "Enable" box.
(5) Only when setting the time of power supply OFF, set the time in the "Power OFF" column, and
put a check mark in the "Enable" box.
(6) When there are more than one day of the week to be set for the power supply ON/OFF
schedule, repeat the procedure (3) to (5).
(7) Click [Add].
Group name
Day of the week
Time of power supply ON
Time of power supply OFF
When validating the
setting, put a check mark
in the box.
Schedule list
Time of power supply ON/OFF

17
6. Schedule setting
<Note>
• The power supply ON and the power supply OFF can not be selected at the same time of the same day of the
week.
• The Schedule Setting will be executed while "ProjectorView Global+" is in operation.
• Depending on usage conditions, such as when there are so many projectors that you need to control, the time to
be executed by the power supply control may deviate from the setting time of the schedule.
• When utilizing the Network Time Protocol (NTP) function on the Internet, the schedule operation may not be
executed because the setting time of the schedule jumps over.
• When the automatic time adjustment by summer time is valid, the schedule operation may not be executed
because the time is automatically adjusted before and after switching over.
6.2. When changing schedule setting
(1) Select a group which you like to change from the Group select pull-down menu on the main
screen.
(2) Select "Edit Schedule Setting" from "Configuration" of the menu bar.
• "Edit Schedule Setting" window is displayed.
(3) Change the contents which you like to correct, and click [Save].
• Corrected contents are reflected.

18
6. Schedule setting
6.3. When deleting group
(1) Select the group which you like to delete from the Group select pull-down menu on the main
screen.
(2) Select "Edit Schedule Setting" from "Configuration" of the menu bar.
• "Edit Schedule Setting" window is displayed.
(3) Click [Delete].
• The selected group is deleted.
<Note>
• When deleting a group, the projector which has belonged to the relevant group will not belong to any group. Set a
new group to belong again on "Edit Projector Setting" window.

19
7. E-mail setting
When the communication with the projector monitored by the theft detector is disrupted, a warning E-mail can be
sent to the designated address, enabling to serve for early detection of the projector theft.
The E-mail setting can not be set at every projector and every group. The same setting should be set for all
projectors.
7.1. Connection with E-mail server
Connect the E-mail server to the network to which the controller PC and the projector are connected that
"ProjectorView Global+" is operating.
7.2. E-mail setting
Designate the address of the E-mail server and the address of the destination to be sent.
<Note>
• As for the network environment, confirm to the network administrator.
(1) Select "Edit E-mail Setting" from "Configuration" of the menu bar on the main screen.
• "Edit E-mail Setting" window is displayed.
(2) Input the setting item for the network environment, and click [Save].
7.3. Sending test E-mail
After completing the setting of the each item on the E-mail Setting window, a test E-mail can be sent to confirm
whether the E-mail is correctly delivered to the destination. When clicking [Test E-mail] at the upper right on the E-
mail Setting window, the test E-mail is issued. Confirm whether the E-mail is correctly delivered to the destination
address.
<Note>
• The E-mail function will be executed while "ProjectorView Global+" is in operation.
• If the test E-mail is not correctly received, confirm the address of the E-mail server and the destination, and the
connection status of the network. For details, make an inquiry to the network administrator.
• The E-mail may possibly not be delivered depending on the certification function of the E-mail server. For details,
make an inquiry to the network administrator.
• When the communication with the projector monitored by the theft detector is disrupted, a theft check error dialog
is displayed.
However, the projector list isn't updated at the same time because it takes some time to update the list.
Item Description
E-mail Server (SMTP) Input the IP address of the E-mail server (Example: 192.168.7.230), or input the
server name (Example: mail.example.com).
Destination E-mail
Address
Input the IP address of the destination to be sent within 64 one-byte characters.
(Up to 3 places can be designated at the maximum.)

20
8. ProjectorView
ProjectorView is a web-browser based remote control and monitoring tool for network projectors.
If you use the projectors listed in page 30, see ProjectorView in "LAN Control Utility" User Manual included with the
projector.
8.1. Main functions
• It displays the status of network projectors (such as the name of the projector, lamp temperature, lamp hours,
errors and alerts).
• It controls network projectors (such as powering on and off network projectors and switching input or lamp
modes).
• It sends an E-mail notification when an error or warning occurs.
8.2. Starting ProjectorView
(1) Select the projector that you want to operate from the list of projectors on the main screen.
• Start ProjectorView for one projector at a time. You cannot concurrently use ProjectorView for multiple
projectors.
(2) Click [ProjectorView] in the tool bar on the main screen.
• The Web browser launches automatically. The password entry window is then displayed.
<Note>
• You can start ProjectorView by manually typing the projector IP address in your web browser's address bar.
• If you are using a proxy server, do not enable proxy settings when accessing the projector IP address.
• Up to three ProjectorView units can be used to control a single projector.
(3) Enter the password and click [OK]. (The default password is "admin".)
• "ProjectorView" main window is displayed.
<Note>
The connection will turn off in five minutes after the password entry window is displayed. You cannot enter the
password then. If this happens, restart the ProjectorView.
ProjectorView main window (PROJECTOR INFORMATION)
When you click PROJECTOR INFORMATION, the Projector Information window is displayed. To display the
information, enter data in the Setup window.
Click [PROJECTOR
INFORMATION] to display the
window on the left.
Click [REMOTE CONTROL] to
display the main window
(REMOTE CONTROL).
Click [SETUP] to display the Setup
window. (See page 22.)
If there is something wrong with
the projector, the red warning
indicator lights.
Details are displayed in the column
below by pointing the cursor to the
contents of failures.
<Note>
See your projector User Manual for
the information on when you
should replace the lamp.