Mitsubishi GOT1000 Series User manual

This manual confers no industrial property rights or any rights of any other kind,
nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be
the cause of Mitsubishi; opportunity loss or lost profits caused by faults in the
Mitsubishi products; damage, secondary damage, accident compensation
caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
For safe use
This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
•
•
•
HEAD OFFICE
HIMEJI WORKS
: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310,
JAPAN
: 840, CHIYODA CHO, HIMEJI, JAPAN
Side
B
Side
A
Side
BJAPANESE ENGLISH
JY997D23401D
Safety Precaution (Read these precautions before using.)
This manual classify the safety precautions into two categories:
and .
Depending on circumstances, procedures indicated by may also be
linked to serious results.
In any case, it is important to follow the directions for usage.
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury or
physical damage.
MOUNTING
PRECAUTIONS
•Use the conversion adaptor in the environment that satisfies the general
specifications described in GT10 User's Manual.
Never use the product in areas with excessive dust, oily smoke, conductive
dusts, corrosive gas (salt air, Cl2, H2S, SO2or NO2), flammable gas,
vibration or impacts, or exposed to high temperature, condensation, or rain
and wind. Not doing so can cause an electric shock, fire, malfunction or
product damage or deterioration.
STARTUP/MAINTENANCE
PRECAUTIONS
•Do not disassemble or modify the conversion adaptor.
Doing so can cause a failure, malfunction, injury or fire.
•Do not touch the conductive and electronic parts of the conversion adaptor
directly. Doing so can cause a unit malfunction or failure.
•When unplugging the conversion adaptor connected to the unit, do not hold
and pull the cable portion. Doing so can cause the unit or cable to be
damaged or can cause a malfunction due to a cable connection fault.
DISPOSAL PRECAUTIONS
•When disposing of the product, handle it as industrial waste.
TRANSPORTATION
PRECAUTIONS
•Make sure to transport the conversion adaptor and/or relevant unit(s) in the
manner they will not be exposed to the impact exceeding the impact
resistance described in the general specifications of this manual, as they are
precision devices. Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
Related Manuals
When using the conversion adaptor, prepare the following manual as well.
As GT10 User's Manual and GT Designer2 Version2 Basic Operation Data Transfer
Manual are sold separately, inquire at our local distributor for it.
For details of a PLC to be connected, refer to the PLC user’s manual respectively.
: Indispensable manual
For the manuals relevant to GOT1000, refer to the PDF manuals stored in the screen
creation software used. For details about a PLC to be connected, refer to the manuals
of PLCs respectively.
For the FA transparent functionality, refer to the GX Developer VersionOperating
Manual.
Bundled Items
1. Overview
The conversion adaptor convert the GOT's RS-232 interface to USB, thereby enabling
the transparent functionality to transfer and monitor the sequence program, and the
project data transfer between the GT10 main unit and the PC. Use this conversion
adaptor with the GT09-C30USB-5P type USB cable.
2. Part Names and External Dimensions
Manual name Manual Number
(Model Code) Contents
GT10
User’s Manual
JY997D24701
(09R819)
Describes the GT10 hardware-relevant
content such as part names, external
dimensions, mounting, wiring,
specifications, and introduction to
option devices.
GT Designer2 Version2
Basic Operation/
Data Transfer Manual
SH-080529ENG
(1D7M24)
Describes methods of the GT
Designer2 installation operation, basic
operation for drawing and transmitting
data to GOT1000 series
Product GT10-R2TUSB 5S RS-232/USB conversion adaptor
Included items USB driver software (CD-ROM)
User's Manual (this manual)
No. Name Specifications
1) RS-232 Connector MINI-DIN 6 Pins (male) : For connecting GOT
2) USB Connector USB MINI : For connecting USB cable
3) Display LED
(POWER)
Green: Lit when the power is properly supplied
(Lit when connected to the PC with a USB cable)
4) Display LED (SD) Red: Lit while sending data (GOT →PC)
5) Display LED (RD) Red: Lit while receiving data (PC →GOT)
GOT
(RS-232)
POWER SD RD
23
(0.9")
Unit
Weight
: mm (inch)
: Approx.40g
75 (2.95")200 (7.87")40 (1.57")
φ12
3) 2)
1)
4) 5)
24
(0.94")
6
(0.23")
15
(0.59")
3. Specifications
3.1 Operating atmosphere
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of
electroconductive dust particles and must be no direct sunlight. (Same as for saving)
General specifications are the same as the GT10 main unit.
For general specifications, refer to the GT10 main unit manual.
3.2 Performance Specifications
3.3 System Requirements (Communication driver)
3.4 USB cable (sold separately)
4. System Configuration
5. Connecting Procedure
1) Turn the GOT power off.
2) Connect the RS-232 connector of the conversion adaptor to the GOT.
3) Connect the USB MINI-B connector of the USB cable to the conversion adaptor.
4) Connect the USB A connector of the USB cable to the personal computor.
5) Turn the GOT power on.
6) Make sure the display LED (POWER) lamp of the conversion adaptor is lit.
(The display LED (POWER) lamp of conversion adaptor lights when power is
supplied normally by the personal computer.)
6. Driver Installation
Procedure for installing the driver is explained below.
Windows®XP installation follows.
•Windows®98, Windows®98SE, Windows®Millennium Edition, and Windows®
2000, the installation method will vary.
Installation of the driver is canceled during the following process, the installation is
not carried out correctly.
If the installation is canceled, uninstall the driver and install again.
Please refer to Chapter 8 for instructions on uninstalling the driver.
Please install the driver with the following procedure.
1) When the USB cable is connected to the personal computer, the following
screen is displayed. (Installation of the software for USB driver)
Insert the included CD-ROM into the personal computer's CD-ROM drive.
Click [ Next > ].
The installation of the USB driver software will begin.
- If using Windows®98, Windows®98SE, Windows®Millennium Edition, and
Windows®2000, A window to select the location of the installation files.
Please select the CD-ROM drive.
2) The following screen is displayed. (Only in Windows®XP)
Click [ Continue Anyway ].
Level Conversion Bidirectional between RS-232 and USB
Communication
Type
GOT RS-232
PC USB2.0 (For full speed)
Transmission speed 115,200/ 57,600/ 38,400/ 19,200/ 9,600/ 4,800 bps
Connector
shape
To GOT MINI DIN 6Pins (Male)
To USB cable USB MINI-B 5Pins (Receptacle)
Supply
voltage
RS-232 side DC5V ±5% (from GOT)
USB side DC5V ±5% (from PC)
Power
consumption
RS-232 side 200mW (40mA/DC5V)
USB side 275mW (55mA/DC5V)
OS
Microsoft®Windows®98, Windows®98SE
Microsoft®Windows®Millennium Edition (Windows®Me)
Microsoft®Windows®2000
Microsoft®Windows®XP
Software GT Designer2
GX Developer
Product name Model name
USB cable GT09-C30USB-
5P (3m) Mitsubishi Electric System Service Co, LTD
GOT
(RS-232)
POWER SD RD
GT10
Conversion adapter
Communication driver
Installing
Personal computer
USB
port
USB cable for connecting a personal computer
(Mitsubishi Electric System Service Co, LTD)
+
B
Note: This product requires USB Driver Installation for each USB port to be
connected. To use multiple USB ports, connect this product to each port, and
install the driver individually. (Depending on the PC environment, Driver
installation may be done automatically.)
3) The following screen is displayed.
Click [ Finish ].
If using Windows®2000 or Windows®XP, proceed to step 4).
- If Windows®98, Windows®98SE or Windows®Millennium Edition is used,
installation of the USB Serial Port software begins, and ends automatically.
The CD-ROM can be removed from the personal computer at this time.
The installation of the USB driver software is finished.
4) The following screen is displayed.
Click [ Next > ].
The installation of the USB Serial Port software will begin.
- If using Windows®2000, a screen to select the location of the installation files
is displayed.
Please select the CD-ROM drive.
5) The screen of 2) is displayed. (Only in Windows®XP)
Click [ Continue Anyway ].
6) The following screen is displayed.
Click [ Finish ].
The installation of the USB Serial Port software will finish.
The CD-ROM (USB driver software) can be removed from the personal
computer at this time.
7. Installation Confirmation of Driver, Setting Software
7.1 Installation Confirmation of Driver
Procedure for confirming the installation of the driver is described below.
Windows®XP example follows.
•In Windows®XP, click [ Start ] → [ Settings ] →[ Control Panel ] →
[ Peformance and Maintenance ] → [ System ] →[ Hardware ] →[ Device
Manager (D) ] and the window below will be displayed.
Please confirm the COM number to which the USB driver is allocated (COM and
LPT).
•If using Windows®98, Windows®98SE, Windows®Millennium Edition or
Windows®2000
A screen that is equivalent to the one below is displayed by clicking [ My
Computer ] →[ Control Panel ] →[ System ] →[ Device Manager ] in the menu of
the personal computer.
Check following:
- GT10-RS2TUSB-5S is indicated at A).
- GT10-RS2TUSB-5S (COM *) is indicated at B).
* indicates the COM number used in Conversion adapter.
- Install the driver again when is displayed.
Select the programming software COM number as the COM number currently
assigned on the screen above.
7.2 Setting Software
7.2.1 Setting GT Designer2
Click [ Communication ] →[ To/From GOT... ] →[ Communication configuration tab ]
→[ RS232 ].
Select the same COM number as the COM number of the personal computer when the
setting communication port screen appears.
Click [ OK ] .
7.2.2 Setting GX Developer
• Connectiong to Q/QnACPU
1) Click [ Online ] →[ Transfer Setup ] .
2) Double-click [ PLC module ] of PLC side I/F.
3) Check [ via GOT [ direct coupled ] transparent mode ].
4) Double-click [ Serial ] of PC side I/F.
Check [ RS-232 ].
Select the same COM number as the COM number of the personal computer
when the setting COM number screen appears.
Click [ OK ] .
B
A
• Connectiong to FXCPU
1) Click [ Online ] → [ Transfer Setup ] .
2) Double-click [ Serial ] of PC side I/F.
3) Check [ RS-232C ].
Select the same COM number as the COM number of the personal computer
when the setting COM number screen appears.
Click [ OK ].
8. Method for Uninstalling Driver
The procedure for uninstalling the driver is explained below.
A Windows® XP example follows.
Please uninstall the driver by the procedure below.
1) Detach the USB cable from the personal computer.
On the PC display, click [ Start ] →[ Control Panel ] →[ Add or Remove
Programs ] →[GT10-RS2TUSB-5S Drivers]. The window below appears..
- In case of Windows®Me of Windows®98 and Windows®98SE and
Windows®Millennium Edition , Windows®2000
A screen that is equivalent to the one below is displayed by clicking
[ My Computer ] →[ Control Panel ] →[ Add/Remove Programs ] in the menu
of the personal computer.
Click [ Change/Remove ].
2) The following screen is displayed.
Click [ Continue ].
3) The following screen is displayed.
Click [ Finish ].
9. Troubleshooting
If communication cannot be established between the GOT and a PC using
conversion adaptor, confirm the following status by checking display LED in
conversion adaptor.
* When the driver softwares for FX-USB-AW/FX3U-USB-BD and GT10-RS2TUSB-
5S are installed, uninstalling one of these driver softwares may cause the other not
to function properly. When this happens, reinstall the driver software.
* When driver installation is required after already establishing USB communication.
→This product requires USB Driver Installation for each USB port to be
connected. Connect the product to a driver-installed USB port, or install the
driver to the current port.
State of POWER LED Contents
POWER LED is lit.
The DC5V power supply from the personal computer is
normally supplied. In case of no communication, check
the status of SD LED and RD LED.
POWER LED is not lit.
The DC 5V power supply from the personal computer is
not supplied. Check the items below.
• Confirm that the specified cable is used to connect
the personal computer.
• Check that the OS is running on the PC.
The status of SD
LED and RD LED. Contents
SD
Blinking Communicating correctly
Extinguished
• Confirm the personal computer and the GOT are
connected properly with the specified cable.
• Check that the software settings on the PC
are correct.
Refer to the Section7.2 Setting software.
For details on software setting procedures, refer to the
respective software manual. .
RD
Blinking Data receiving
Extinguished
• Confirm that the power is supplied to GOT.
• Confirm the personal computer and the GOT are
connected properly with the specified cable.
• Check that the software settings on the PC are
correct. Refer to the Section7.2 Setting software.
For details on software setting procedures, refer to the
respective software manual. .
RS-232 / USB Conversion adaptor
USER’S MANUAL
This manual describes the part names, external dimensions and specifications
of the product. Before use, read this manual and manuals of relevant products
fully to acquire proficiency in handling and operating the product. Make sure to
learn all the product information, safety information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this manual are
the registered trademarks or trademarks of each company.
Effective Sep 2008
Specifications are subject to change without notice.
©2008 Mitsubishi Electric Corporation
Manual Number JY997D23401D
Date Sep 2008

This manual confers no industrial property rights or any rights of any other kind,
nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be
the cause of Mitsubishi; opportunity loss or lost profits caused by faults in the
Mitsubishi products; damage, secondary damage, accident compensation
caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
For safe use
This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
•
•
•
HEAD OFFICE
HIMEJI WORKS
: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310,
JAPAN
: 840, CHIYODA CHO, HIMEJI, JAPAN
Side
B
Side
A
Side
BJAPANESE ENGLISH
JY997D23401D
Safety Precaution (Read these precautions before using.)
This manual classify the safety precautions into two categories:
and .
Depending on circumstances, procedures indicated by may also be
linked to serious results.
In any case, it is important to follow the directions for usage.
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury or
physical damage.
MOUNTING
PRECAUTIONS
•Use the conversion adaptor in the environment that satisfies the general
specifications described in GT10 User's Manual.
Never use the product in areas with excessive dust, oily smoke, conductive
dusts, corrosive gas (salt air, Cl2, H2S, SO2or NO2), flammable gas,
vibration or impacts, or exposed to high temperature, condensation, or rain
and wind. Not doing so can cause an electric shock, fire, malfunction or
product damage or deterioration.
STARTUP/MAINTENANCE
PRECAUTIONS
•Do not disassemble or modify the conversion adaptor.
Doing so can cause a failure, malfunction, injury or fire.
•Do not touch the conductive and electronic parts of the conversion adaptor
directly. Doing so can cause a unit malfunction or failure.
•When unplugging the conversion adaptor connected to the unit, do not hold
and pull the cable portion. Doing so can cause the unit or cable to be
damaged or can cause a malfunction due to a cable connection fault.
DISPOSAL PRECAUTIONS
•When disposing of the product, handle it as industrial waste.
TRANSPORTATION
PRECAUTIONS
•Make sure to transport the conversion adaptor and/or relevant unit(s) in the
manner they will not be exposed to the impact exceeding the impact
resistance described in the general specifications of this manual, as they are
precision devices. Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
Related Manuals
When using the conversion adaptor, prepare the following manual as well.
As GT10 User's Manual and GT Designer2 Version2 Basic Operation Data Transfer
Manual are sold separately, inquire at our local distributor for it.
For details of a PLC to be connected, refer to the PLC user’s manual respectively.
: Indispensable manual
For the manuals relevant to GOT1000, refer to the PDF manuals stored in the screen
creation software used. For details about a PLC to be connected, refer to the manuals
of PLCs respectively.
For the FA transparent functionality, refer to the GX Developer VersionOperating
Manual.
Bundled Items
1. Overview
The conversion adaptor convert the GOT's RS-232 interface to USB, thereby enabling
the transparent functionality to transfer and monitor the sequence program, and the
project data transfer between the GT10 main unit and the PC. Use this conversion
adaptor with the GT09-C30USB-5P type USB cable.
2. Part Names and External Dimensions
Manual name Manual Number
(Model Code) Contents
GT10
User’s Manual
JY997D24701
(09R819)
Describes the GT10 hardware-relevant
content such as part names, external
dimensions, mounting, wiring,
specifications, and introduction to
option devices.
GT Designer2 Version2
Basic Operation/
Data Transfer Manual
SH-080529ENG
(1D7M24)
Describes methods of the GT
Designer2 installation operation, basic
operation for drawing and transmitting
data to GOT1000 series
Product GT10-R2TUSB 5S RS-232/USB conversion adaptor
Included items USB driver software (CD-ROM)
User's Manual (this manual)
No. Name Specifications
1) RS-232 Connector MINI-DIN 6 Pins (male) : For connecting GOT
2) USB Connector USB MINI : For connecting USB cable
3) Display LED
(POWER)
Green: Lit when the power is properly supplied
(Lit when connected to the PC with a USB cable)
4) Display LED (SD) Red: Lit while sending data (GOT →PC)
5) Display LED (RD) Red: Lit while receiving data (PC →GOT)
GOT
(RS-232)
POWER SD RD
23
(0.9")
Unit
Weight
: mm (inch)
: Approx.40g
75 (2.95")200 (7.87")40 (1.57")
φ12
3) 2)
1)
4) 5)
24
(0.94")
6
(0.23")
15
(0.59")
3. Specifications
3.1 Operating atmosphere
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of
electroconductive dust particles and must be no direct sunlight. (Same as for saving)
General specifications are the same as the GT10 main unit.
For general specifications, refer to the GT10 main unit manual.
3.2 Performance Specifications
3.3 System Requirements (Communication driver)
3.4 USB cable (sold separately)
4. System Configuration
5. Connecting Procedure
1) Turn the GOT power off.
2) Connect the RS-232 connector of the conversion adaptor to the GOT.
3) Connect the USB MINI-B connector of the USB cable to the conversion adaptor.
4) Connect the USB A connector of the USB cable to the personal computor.
5) Turn the GOT power on.
6) Make sure the display LED (POWER) lamp of the conversion adaptor is lit.
(The display LED (POWER) lamp of conversion adaptor lights when power is
supplied normally by the personal computer.)
6. Driver Installation
Procedure for installing the driver is explained below.
Windows®XP installation follows.
•Windows®98, Windows®98SE, Windows®Millennium Edition, and Windows®
2000, the installation method will vary.
Installation of the driver is canceled during the following process, the installation is
not carried out correctly.
If the installation is canceled, uninstall the driver and install again.
Please refer to Chapter 8 for instructions on uninstalling the driver.
Please install the driver with the following procedure.
1) When the USB cable is connected to the personal computer, the following
screen is displayed. (Installation of the software for USB driver)
Insert the included CD-ROM into the personal computer's CD-ROM drive.
Click [ Next > ].
The installation of the USB driver software will begin.
- If using Windows®98, Windows®98SE, Windows®Millennium Edition, and
Windows®2000, A window to select the location of the installation files.
Please select the CD-ROM drive.
2) The following screen is displayed. (Only in Windows®XP)
Click [ Continue Anyway ].
Level Conversion Bidirectional between RS-232 and USB
Communication
Type
GOT RS-232
PC USB2.0 (For full speed)
Transmission speed 115,200/ 57,600/ 38,400/ 19,200/ 9,600/ 4,800 bps
Connector
shape
To GOT MINI DIN 6Pins (Male)
To USB cable USB MINI-B 5Pins (Receptacle)
Supply
voltage
RS-232 side DC5V ±5% (from GOT)
USB side DC5V ±5% (from PC)
Power
consumption
RS-232 side 200mW (40mA/DC5V)
USB side 275mW (55mA/DC5V)
OS
Microsoft®Windows®98, Windows®98SE
Microsoft®Windows®Millennium Edition (Windows®Me)
Microsoft®Windows®2000
Microsoft®Windows®XP
Software GT Designer2
GX Developer
Product name Model name
USB cable GT09-C30USB-
5P (3m) Mitsubishi Electric System Service Co, LTD
GOT
(RS-232)
POWER SD RD
GT10
Conversion adapter
Communication driver
Installing
Personal computer
USB
port
USB cable for connecting a personal computer
(Mitsubishi Electric System Service Co, LTD)
+
B
Note: This product requires USB Driver Installation for each USB port to be
connected. To use multiple USB ports, connect this product to each port, and
install the driver individually. (Depending on the PC environment, Driver
installation may be done automatically.)
3) The following screen is displayed.
Click [ Finish ].
If using Windows®2000 or Windows®XP, proceed to step 4).
- If Windows®98, Windows®98SE or Windows®Millennium Edition is used,
installation of the USB Serial Port software begins, and ends automatically.
The CD-ROM can be removed from the personal computer at this time.
The installation of the USB driver software is finished.
4) The following screen is displayed.
Click [ Next > ].
The installation of the USB Serial Port software will begin.
- If using Windows®2000, a screen to select the location of the installation files
is displayed.
Please select the CD-ROM drive.
5) The screen of 2) is displayed. (Only in Windows®XP)
Click [ Continue Anyway ].
6) The following screen is displayed.
Click [ Finish ].
The installation of the USB Serial Port software will finish.
The CD-ROM (USB driver software) can be removed from the personal
computer at this time.
7. Installation Confirmation of Driver, Setting Software
7.1 Installation Confirmation of Driver
Procedure for confirming the installation of the driver is described below.
Windows®XP example follows.
•In Windows®XP, click [ Start ] → [ Settings ] →[ Control Panel ] →
[ Peformance and Maintenance ] → [ System ] →[ Hardware ] →[ Device
Manager (D) ] and the window below will be displayed.
Please confirm the COM number to which the USB driver is allocated (COM and
LPT).
•If using Windows®98, Windows®98SE, Windows®Millennium Edition or
Windows®2000
A screen that is equivalent to the one below is displayed by clicking [ My
Computer ] →[ Control Panel ] →[ System ] →[ Device Manager ] in the menu of
the personal computer.
Check following:
- GT10-RS2TUSB-5S is indicated at A).
- GT10-RS2TUSB-5S (COM *) is indicated at B).
* indicates the COM number used in Conversion adapter.
- Install the driver again when is displayed.
Select the programming software COM number as the COM number currently
assigned on the screen above.
7.2 Setting Software
7.2.1 Setting GT Designer2
Click [ Communication ] →[ To/From GOT... ] →[ Communication configuration tab ]
→[ RS232 ].
Select the same COM number as the COM number of the personal computer when the
setting communication port screen appears.
Click [ OK ] .
7.2.2 Setting GX Developer
• Connectiong to Q/QnACPU
1) Click [ Online ] →[ Transfer Setup ] .
2) Double-click [ PLC module ] of PLC side I/F.
3) Check [ via GOT [ direct coupled ] transparent mode ].
4) Double-click [ Serial ] of PC side I/F.
Check [ RS-232 ].
Select the same COM number as the COM number of the personal computer
when the setting COM number screen appears.
Click [ OK ] .
B
A
• Connectiong to FXCPU
1) Click [ Online ] → [ Transfer Setup ] .
2) Double-click [ Serial ] of PC side I/F.
3) Check [ RS-232C ].
Select the same COM number as the COM number of the personal computer
when the setting COM number screen appears.
Click [ OK ].
8. Method for Uninstalling Driver
The procedure for uninstalling the driver is explained below.
A Windows® XP example follows.
Please uninstall the driver by the procedure below.
1) Detach the USB cable from the personal computer.
On the PC display, click [ Start ] →[ Control Panel ] →[ Add or Remove
Programs ] →[GT10-RS2TUSB-5S Drivers]. The window below appears..
- In case of Windows®Me of Windows®98 and Windows®98SE and
Windows®Millennium Edition , Windows®2000
A screen that is equivalent to the one below is displayed by clicking
[ My Computer ] →[ Control Panel ] →[ Add/Remove Programs ] in the menu
of the personal computer.
Click [ Change/Remove ].
2) The following screen is displayed.
Click [ Continue ].
3) The following screen is displayed.
Click [ Finish ].
9. Troubleshooting
If communication cannot be established between the GOT and a PC using
conversion adaptor, confirm the following status by checking display LED in
conversion adaptor.
* When the driver softwares for FX-USB-AW/FX3U-USB-BD and GT10-RS2TUSB-
5S are installed, uninstalling one of these driver softwares may cause the other not
to function properly. When this happens, reinstall the driver software.
* When driver installation is required after already establishing USB communication.
→This product requires USB Driver Installation for each USB port to be
connected. Connect the product to a driver-installed USB port, or install the
driver to the current port.
State of POWER LED Contents
POWER LED is lit.
The DC5V power supply from the personal computer is
normally supplied. In case of no communication, check
the status of SD LED and RD LED.
POWER LED is not lit.
The DC 5V power supply from the personal computer is
not supplied. Check the items below.
• Confirm that the specified cable is used to connect
the personal computer.
• Check that the OS is running on the PC.
The status of SD
LED and RD LED. Contents
SD
Blinking Communicating correctly
Extinguished
• Confirm the personal computer and the GOT are
connected properly with the specified cable.
• Check that the software settings on the PC
are correct.
Refer to the Section7.2 Setting software.
For details on software setting procedures, refer to the
respective software manual. .
RD
Blinking Data receiving
Extinguished
• Confirm that the power is supplied to GOT.
• Confirm the personal computer and the GOT are
connected properly with the specified cable.
• Check that the software settings on the PC are
correct. Refer to the Section7.2 Setting software.
For details on software setting procedures, refer to the
respective software manual. .
RS-232 / USB Conversion adaptor
USER’S MANUAL
This manual describes the part names, external dimensions and specifications
of the product. Before use, read this manual and manuals of relevant products
fully to acquire proficiency in handling and operating the product. Make sure to
learn all the product information, safety information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this manual are
the registered trademarks or trademarks of each company.
Effective Sep 2008
Specifications are subject to change without notice.
©2008 Mitsubishi Electric Corporation
Manual Number JY997D23401D
Date Sep 2008

This manual confers no industrial property rights or any rights of any other kind,
nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be
the cause of Mitsubishi; opportunity loss or lost profits caused by faults in the
Mitsubishi products; damage, secondary damage, accident compensation
caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
For safe use
This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
•
•
•
HEAD OFFICE
HIMEJI WORKS
: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310,
JAPAN
: 840, CHIYODA CHO, HIMEJI, JAPAN
Side
B
Side
A
Side
BJAPANESE ENGLISH
JY997D23401D
Safety Precaution (Read these precautions before using.)
This manual classify the safety precautions into two categories:
and .
Depending on circumstances, procedures indicated by may also be
linked to serious results.
In any case, it is important to follow the directions for usage.
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury or
physical damage.
MOUNTING
PRECAUTIONS
•Use the conversion adaptor in the environment that satisfies the general
specifications described in GT10 User's Manual.
Never use the product in areas with excessive dust, oily smoke, conductive
dusts, corrosive gas (salt air, Cl2, H2S, SO2or NO2), flammable gas,
vibration or impacts, or exposed to high temperature, condensation, or rain
and wind. Not doing so can cause an electric shock, fire, malfunction or
product damage or deterioration.
STARTUP/MAINTENANCE
PRECAUTIONS
•Do not disassemble or modify the conversion adaptor.
Doing so can cause a failure, malfunction, injury or fire.
•Do not touch the conductive and electronic parts of the conversion adaptor
directly. Doing so can cause a unit malfunction or failure.
•When unplugging the conversion adaptor connected to the unit, do not hold
and pull the cable portion. Doing so can cause the unit or cable to be
damaged or can cause a malfunction due to a cable connection fault.
DISPOSAL PRECAUTIONS
•When disposing of the product, handle it as industrial waste.
TRANSPORTATION
PRECAUTIONS
•Make sure to transport the conversion adaptor and/or relevant unit(s) in the
manner they will not be exposed to the impact exceeding the impact
resistance described in the general specifications of this manual, as they are
precision devices. Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
Related Manuals
When using the conversion adaptor, prepare the following manual as well.
As GT10 User's Manual and GT Designer2 Version2 Basic Operation Data Transfer
Manual are sold separately, inquire at our local distributor for it.
For details of a PLC to be connected, refer to the PLC user’s manual respectively.
: Indispensable manual
For the manuals relevant to GOT1000, refer to the PDF manuals stored in the screen
creation software used. For details about a PLC to be connected, refer to the manuals
of PLCs respectively.
For the FA transparent functionality, refer to the GX Developer VersionOperating
Manual.
Bundled Items
1. Overview
The conversion adaptor convert the GOT's RS-232 interface to USB, thereby enabling
the transparent functionality to transfer and monitor the sequence program, and the
project data transfer between the GT10 main unit and the PC. Use this conversion
adaptor with the GT09-C30USB-5P type USB cable.
2. Part Names and External Dimensions
Manual name Manual Number
(Model Code) Contents
GT10
User’s Manual
JY997D24701
(09R819)
Describes the GT10 hardware-relevant
content such as part names, external
dimensions, mounting, wiring,
specifications, and introduction to
option devices.
GT Designer2 Version2
Basic Operation/
Data Transfer Manual
SH-080529ENG
(1D7M24)
Describes methods of the GT
Designer2 installation operation, basic
operation for drawing and transmitting
data to GOT1000 series
Product GT10-R2TUSB 5S RS-232/USB conversion adaptor
Included items USB driver software (CD-ROM)
User's Manual (this manual)
No. Name Specifications
1) RS-232 Connector MINI-DIN 6 Pins (male) : For connecting GOT
2) USB Connector USB MINI : For connecting USB cable
3) Display LED
(POWER)
Green: Lit when the power is properly supplied
(Lit when connected to the PC with a USB cable)
4) Display LED (SD) Red: Lit while sending data (GOT →PC)
5) Display LED (RD) Red: Lit while receiving data (PC →GOT)
GOT
(RS-232)
POWER SD RD
23
(0.9")
Unit
Weight
: mm (inch)
: Approx.40g
75 (2.95")200 (7.87")40 (1.57")
φ12
3) 2)
1)
4) 5)
24
(0.94")
6
(0.23")
15
(0.59")
3. Specifications
3.1 Operating atmosphere
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of
electroconductive dust particles and must be no direct sunlight. (Same as for saving)
General specifications are the same as the GT10 main unit.
For general specifications, refer to the GT10 main unit manual.
3.2 Performance Specifications
3.3 System Requirements (Communication driver)
3.4 USB cable (sold separately)
4. System Configuration
5. Connecting Procedure
1) Turn the GOT power off.
2) Connect the RS-232 connector of the conversion adaptor to the GOT.
3) Connect the USB MINI-B connector of the USB cable to the conversion adaptor.
4) Connect the USB A connector of the USB cable to the personal computor.
5) Turn the GOT power on.
6) Make sure the display LED (POWER) lamp of the conversion adaptor is lit.
(The display LED (POWER) lamp of conversion adaptor lights when power is
supplied normally by the personal computer.)
6. Driver Installation
Procedure for installing the driver is explained below.
Windows®XP installation follows.
•Windows®98, Windows®98SE, Windows®Millennium Edition, and Windows®
2000, the installation method will vary.
Installation of the driver is canceled during the following process, the installation is
not carried out correctly.
If the installation is canceled, uninstall the driver and install again.
Please refer to Chapter 8 for instructions on uninstalling the driver.
Please install the driver with the following procedure.
1) When the USB cable is connected to the personal computer, the following
screen is displayed. (Installation of the software for USB driver)
Insert the included CD-ROM into the personal computer's CD-ROM drive.
Click [ Next > ].
The installation of the USB driver software will begin.
- If using Windows®98, Windows®98SE, Windows®Millennium Edition, and
Windows®2000, A window to select the location of the installation files.
Please select the CD-ROM drive.
2) The following screen is displayed. (Only in Windows®XP)
Click [ Continue Anyway ].
Level Conversion Bidirectional between RS-232 and USB
Communication
Type
GOT RS-232
PC USB2.0 (For full speed)
Transmission speed 115,200/ 57,600/ 38,400/ 19,200/ 9,600/ 4,800 bps
Connector
shape
To GOT MINI DIN 6Pins (Male)
To USB cable USB MINI-B 5Pins (Receptacle)
Supply
voltage
RS-232 side DC5V ±5% (from GOT)
USB side DC5V ±5% (from PC)
Power
consumption
RS-232 side 200mW (40mA/DC5V)
USB side 275mW (55mA/DC5V)
OS
Microsoft®Windows®98, Windows®98SE
Microsoft®Windows®Millennium Edition (Windows®Me)
Microsoft®Windows®2000
Microsoft®Windows®XP
Software GT Designer2
GX Developer
Product name Model name
USB cable GT09-C30USB-
5P (3m) Mitsubishi Electric System Service Co, LTD
GOT
(RS-232)
POWER SD RD
GT10
Conversion adapter
Communication driver
Installing
Personal computer
USB
port
USB cable for connecting a personal computer
(Mitsubishi Electric System Service Co, LTD)
+
B
Note: This product requires USB Driver Installation for each USB port to be
connected. To use multiple USB ports, connect this product to each port, and
install the driver individually. (Depending on the PC environment, Driver
installation may be done automatically.)
3) The following screen is displayed.
Click [ Finish ].
If using Windows®2000 or Windows®XP, proceed to step 4).
- If Windows®98, Windows®98SE or Windows®Millennium Edition is used,
installation of the USB Serial Port software begins, and ends automatically.
The CD-ROM can be removed from the personal computer at this time.
The installation of the USB driver software is finished.
4) The following screen is displayed.
Click [ Next > ].
The installation of the USB Serial Port software will begin.
- If using Windows®2000, a screen to select the location of the installation files
is displayed.
Please select the CD-ROM drive.
5) The screen of 2) is displayed. (Only in Windows®XP)
Click [ Continue Anyway ].
6) The following screen is displayed.
Click [ Finish ].
The installation of the USB Serial Port software will finish.
The CD-ROM (USB driver software) can be removed from the personal
computer at this time.
7. Installation Confirmation of Driver, Setting Software
7.1 Installation Confirmation of Driver
Procedure for confirming the installation of the driver is described below.
Windows®XP example follows.
•In Windows®XP, click [ Start ] → [ Settings ] →[ Control Panel ] →
[ Peformance and Maintenance ] → [ System ] →[ Hardware ] →[ Device
Manager (D) ] and the window below will be displayed.
Please confirm the COM number to which the USB driver is allocated (COM and
LPT).
•If using Windows®98, Windows®98SE, Windows®Millennium Edition or
Windows®2000
A screen that is equivalent to the one below is displayed by clicking [ My
Computer ] →[ Control Panel ] →[ System ] →[ Device Manager ] in the menu of
the personal computer.
Check following:
- GT10-RS2TUSB-5S is indicated at A).
- GT10-RS2TUSB-5S (COM *) is indicated at B).
* indicates the COM number used in Conversion adapter.
- Install the driver again when is displayed.
Select the programming software COM number as the COM number currently
assigned on the screen above.
7.2 Setting Software
7.2.1 Setting GT Designer2
Click [ Communication ] →[ To/From GOT... ] →[ Communication configuration tab ]
→[ RS232 ].
Select the same COM number as the COM number of the personal computer when the
setting communication port screen appears.
Click [ OK ] .
7.2.2 Setting GX Developer
• Connectiong to Q/QnACPU
1) Click [ Online ] →[ Transfer Setup ] .
2) Double-click [ PLC module ] of PLC side I/F.
3) Check [ via GOT [ direct coupled ] transparent mode ].
4) Double-click [ Serial ] of PC side I/F.
Check [ RS-232 ].
Select the same COM number as the COM number of the personal computer
when the setting COM number screen appears.
Click [ OK ] .
B
A
• Connectiong to FXCPU
1) Click [ Online ] → [ Transfer Setup ] .
2) Double-click [ Serial ] of PC side I/F.
3) Check [ RS-232C ].
Select the same COM number as the COM number of the personal computer
when the setting COM number screen appears.
Click [ OK ].
8. Method for Uninstalling Driver
The procedure for uninstalling the driver is explained below.
A Windows® XP example follows.
Please uninstall the driver by the procedure below.
1) Detach the USB cable from the personal computer.
On the PC display, click [ Start ] →[ Control Panel ] →[ Add or Remove
Programs ] →[GT10-RS2TUSB-5S Drivers]. The window below appears..
- In case of Windows®Me of Windows®98 and Windows®98SE and
Windows®Millennium Edition , Windows®2000
A screen that is equivalent to the one below is displayed by clicking
[ My Computer ] →[ Control Panel ] →[ Add/Remove Programs ] in the menu
of the personal computer.
Click [ Change/Remove ].
2) The following screen is displayed.
Click [ Continue ].
3) The following screen is displayed.
Click [ Finish ].
9. Troubleshooting
If communication cannot be established between the GOT and a PC using
conversion adaptor, confirm the following status by checking display LED in
conversion adaptor.
* When the driver softwares for FX-USB-AW/FX3U-USB-BD and GT10-RS2TUSB-
5S are installed, uninstalling one of these driver softwares may cause the other not
to function properly. When this happens, reinstall the driver software.
* When driver installation is required after already establishing USB communication.
→This product requires USB Driver Installation for each USB port to be
connected. Connect the product to a driver-installed USB port, or install the
driver to the current port.
State of POWER LED Contents
POWER LED is lit.
The DC5V power supply from the personal computer is
normally supplied. In case of no communication, check
the status of SD LED and RD LED.
POWER LED is not lit.
The DC 5V power supply from the personal computer is
not supplied. Check the items below.
• Confirm that the specified cable is used to connect
the personal computer.
• Check that the OS is running on the PC.
The status of SD
LED and RD LED. Contents
SD
Blinking Communicating correctly
Extinguished
• Confirm the personal computer and the GOT are
connected properly with the specified cable.
• Check that the software settings on the PC
are correct.
Refer to the Section7.2 Setting software.
For details on software setting procedures, refer to the
respective software manual. .
RD
Blinking Data receiving
Extinguished
• Confirm that the power is supplied to GOT.
• Confirm the personal computer and the GOT are
connected properly with the specified cable.
• Check that the software settings on the PC are
correct. Refer to the Section7.2 Setting software.
For details on software setting procedures, refer to the
respective software manual. .
RS-232 / USB Conversion adaptor
USER’S MANUAL
This manual describes the part names, external dimensions and specifications
of the product. Before use, read this manual and manuals of relevant products
fully to acquire proficiency in handling and operating the product. Make sure to
learn all the product information, safety information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this manual are
the registered trademarks or trademarks of each company.
Effective Sep 2008
Specifications are subject to change without notice.
©2008 Mitsubishi Electric Corporation
Manual Number JY997D23401D
Date Sep 2008