Mixx Audio NekFit Sports User manual

User manual
Product Specication
Power Output: 2.5W
Speaker: 51mm
Frequency Response: 100-20,000 Hz
SNR: >89dB
Size: 110mm x 120mm x 95mm
Charging Time: 4 hours
Playing Time: 6.5 hours
Warning
- This speaker contains a lithium battery. It must be used and charged correctly
- Improper use of this speaker may cause the battery to catch re or explode resulting in
serious or fatal injury
- The battery shall not be exposed to excessive heat such as sunshine, re or suchlike
Caution
- Do not disassemble or modify the speaker
- Do not plave the speaker in direct sunlight, near res, stoves or other high temperatures
- Do not expose the speaker to water, salt water or allow the speaker to get wet
- If you dispose of the speaker, remember it contains a lithium battery and recycle
accordingly
Correct disposal of this product
This marking indicates that this product should not be disposed of with
other household wastes throught the EU.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of material resources.
To return your used devices, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for environmentally
safe recycling.
For Support, please contactMixx Audio
via the website at www.mixx-audio.com
or email support at: [e-mail]
3
Mixx S3 User Manual v1.indd 1-5 30/06/2016 23:03
Listening to Music
1. Check if the Bluetooth Status LED is ashing (ready to pair) or continuously
lit (paired and connected to a phone / music player). To enter pairing mode
simultaneously press and hold the ‘Up’ and ‘Down’ buttons.
2. To pair your phone with the Mixx S3, go to your bluetooth settings and
search for ‘Mixx S3’ then pair with the speaker (you may need to consult
your phone / music players instruction manual for specic pairing
instructions). Once pairing has completed, the Bluetooth Status LED will
be lit continuously
3. Select music to play on your phone. Adjust the volume on your phone
to maximum, then use the ‘UP’/’Down’ buttons on the rear panel of the
speaker to adjust the volume to the desired listening level.
4. To listen to music via the AUX in socket, use a 3.5mm audio cable (not
included) to connect the speaker to your music source. The Bluetooth
Status LED will illuminate GREEN to indicate it is in AUX In mode, and
the Auxilliary input will automatically be selected for audio playback.
Answering Calls
Should you receive a phone call whilst using the Mixx S3 with
Bluetooth, you can answer it and talk hands free using the
built in microphone on the front of the Mixx S3. Answer the
call from the screen on your phone and select ‘Mixx S3’ as the
speaker for the call.
Note: The background noise may increase when the battery
charge level is low. Some audio devices such as laptops
may generate increased noise at higher volumes.
Charging the S3
When the Mixx S3 displays ‘LO’ on the clock this indicates that it
is time to charge the internal battery. Use the supplied USB cable
and power adapter to charge the battery from the nearest
convenient wall outlet. The Charge Status LED will illuminate Orange
whilst charging, and Green when fully charged.
User manual
Product Specication
Power Output: 2.5W
Speaker: 51mm
Frequency Response: 100-20,000 Hz
SNR: >89dB
Size: 110mm x 120mm x 95mm
Charging Time: 4 hours
Playing Time: 6.5 hours
Warning
- This speaker contains a lithium battery. It must be used and charged correctly
- Improper use of this speaker may cause the battery to catch re or explode resulting in
serious or fatal injury
- The battery shall not be exposed to excessive heat such as sunshine, re or suchlike
Caution
- Do not disassemble or modify the speaker
- Do not plave the speaker in direct sunlight, near res, stoves or other high temperatures
- Do not expose the speaker to water, salt water or allow the speaker to get wet
- If you dispose of the speaker, remember it contains a lithium battery and recycle
accordingly
Correct disposal of this product
This marking indicates that this product should not be disposed of with
other household wastes throught the EU.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of material resources.
To return your used devices, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for environmentally
safe recycling.
For Support, please contactMixx Audio
via the website at www.mixx-audio.com
or email support at: [e-mail]
3
Mixx S3 User Manual v1.indd 1-5 30/06/2016 23:03
Listening to Music
1. Check if the Bluetooth Status LED is ashing (ready to pair) or continuously
lit (paired and connected to a phone / music player). To enter pairing mode
simultaneously press and hold the ‘Up’ and ‘Down’ buttons.
2. To pair your phone with the Mixx S3, go to your bluetooth settings and
search for ‘Mixx S3’ then pair with the speaker (you may need to consult
your phone / music players instruction manual for specic pairing
instructions). Once pairing has completed, the Bluetooth Status LED will
be lit continuously
3. Select music to play on your phone. Adjust the volume on your phone
to maximum, then use the ‘UP’/’Down’ buttons on the rear panel of the
speaker to adjust the volume to the desired listening level.
4. To listen to music via the AUX in socket, use a 3.5mm audio cable (not
included) to connect the speaker to your music source. The Bluetooth
Status LED will illuminate GREEN to indicate it is in AUX In mode, and
the Auxilliary input will automatically be selected for audio playback.
Answering Calls
Should you receive a phone call whilst using the Mixx S3 with
Bluetooth, you can answer it and talk hands free using the
built in microphone on the front of the Mixx S3. Answer the
call from the screen on your phone and select ‘Mixx S3’ as the
speaker for the call.
Note: The background noise may increase when the battery
charge level is low. Some audio devices such as laptops
may generate increased noise at higher volumes.
Charging the S3
When the Mixx S3 displays ‘LO’ on the clock this indicates that it
is time to charge the internal battery. Use the supplied USB cable
and power adapter to charge the battery from the nearest
convenient wall outlet. The Charge Status LED will illuminate Orange
whilst charging, and Green when fully charged.
User manual
Product Specication
Power Output: 2.5W
Speaker: 51mm
Frequency Response: 100-20,000 Hz
SNR: >89dB
Size: 110mm x 120mm x 95mm
Charging Time: 4 hours
Playing Time: 6.5 hours
Warning
- This speaker contains a lithium battery. It must be used and charged correctly
- Improper use of this speaker may cause the battery to catch re or explode resulting in
serious or fatal injury
- The battery shall not be exposed to excessive heat such as sunshine, re or suchlike
Caution
- Do not disassemble or modify the speaker
- Do not plave the speaker in direct sunlight, near res, stoves or other high temperatures
- Do not expose the speaker to water, salt water or allow the speaker to get wet
- If you dispose of the speaker, remember it contains a lithium battery and recycle
accordingly
Correct disposal of this product
This marking indicates that this product should not be disposed of with
other household wastes throught the EU.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of material resources.
To return your used devices, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for environmentally
safe recycling.
For Support, please contactMixx Audio
via the website at www.mixx-audio.com
or email support at: [e-mail]
3
Mixx S3 User Manual v1.indd 1-5 30/06/2016 23:03
Listening to Music
1. Check if the Bluetooth Status LED is ashing (ready to pair) or continuously
lit (paired and connected to a phone / music player). To enter pairing mode
simultaneously press and hold the ‘Up’ and ‘Down’ buttons.
2. To pair your phone with the Mixx S3, go to your bluetooth settings and
search for ‘Mixx S3’ then pair with the speaker (you may need to consult
your phone / music players instruction manual for specic pairing
instructions). Once pairing has completed, the Bluetooth Status LED will
be lit continuously
3. Select music to play on your phone. Adjust the volume on your phone
to maximum, then use the ‘UP’/’Down’ buttons on the rear panel of the
speaker to adjust the volume to the desired listening level.
4. To listen to music via the AUX in socket, use a 3.5mm audio cable (not
included) to connect the speaker to your music source. The Bluetooth
Status LED will illuminate GREEN to indicate it is in AUX In mode, and
the Auxilliary input will automatically be selected for audio playback.
Answering Calls
Should you receive a phone call whilst using the Mixx S3 with
Bluetooth, you can answer it and talk hands free using the
built in microphone on the front of the Mixx S3. Answer the
call from the screen on your phone and select ‘Mixx S3’ as the
speaker for the call.
Note: The background noise may increase when the battery
charge level is low. Some audio devices such as laptops
may generate increased noise at higher volumes.
Charging the S3
When the Mixx S3 displays ‘LO’ on the clock this indicates that it
is time to charge the internal battery. Use the supplied USB cable
and power adapter to charge the battery from the nearest
convenient wall outlet. The Charge Status LED will illuminate Orange
whilst charging, and Green when fully charged.
User manual
Product Specication
Power Output: 2.5W
Speaker: 51mm
Frequency Response: 100-20,000 Hz
SNR: >89dB
Size: 110mm x 120mm x 95mm
Charging Time: 4 hours
Playing Time: 6.5 hours
Warning
- This speaker contains a lithium battery. It must be used and charged correctly
- Improper use of this speaker may cause the battery to catch re or explode resulting in
serious or fatal injury
- The battery shall not be exposed to excessive heat such as sunshine, re or suchlike
Caution
- Do not disassemble or modify the speaker
- Do not plave the speaker in direct sunlight, near res, stoves or other high temperatures
- Do not expose the speaker to water, salt water or allow the speaker to get wet
- If you dispose of the speaker, remember it contains a lithium battery and recycle
accordingly
Correct disposal of this product
This marking indicates that this product should not be disposed of with
other household wastes throught the EU.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of material resources.
To return your used devices, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for environmentally
safe recycling.
For Support, please contactMixx Audio
via the website at www.mixx-audio.com
or email support at: [e-mail]
3
Mixx S3 User Manual v1.indd 1-5 30/06/2016 23:03
Listening to Music
1. Check if the Bluetooth Status LED is ashing (ready to pair) or continuously
lit (paired and connected to a phone / music player). To enter pairing mode
simultaneously press and hold the ‘Up’ and ‘Down’ buttons.
2. To pair your phone with the Mixx S3, go to your bluetooth settings and
search for ‘Mixx S3’ then pair with the speaker (you may need to consult
your phone / music players instruction manual for specic pairing
instructions). Once pairing has completed, the Bluetooth Status LED will
be lit continuously
3. Select music to play on your phone. Adjust the volume on your phone
to maximum, then use the ‘UP’/’Down’ buttons on the rear panel of the
speaker to adjust the volume to the desired listening level.
4. To listen to music via the AUX in socket, use a 3.5mm audio cable (not
included) to connect the speaker to your music source. The Bluetooth
Status LED will illuminate GREEN to indicate it is in AUX In mode, and
the Auxilliary input will automatically be selected for audio playback.
Answering Calls
Should you receive a phone call whilst using the Mixx S3 with
Bluetooth, you can answer it and talk hands free using the
built in microphone on the front of the Mixx S3. Answer the
call from the screen on your phone and select ‘Mixx S3’ as the
speaker for the call.
Note: The background noise may increase when the battery
charge level is low. Some audio devices such as laptops
may generate increased noise at higher volumes.
Charging the S3
When the Mixx S3 displays ‘LO’ on the clock this indicates that it
is time to charge the internal battery. Use the supplied USB cable
and power adapter to charge the battery from the nearest
convenient wall outlet. The Charge Status LED will illuminate Orange
whilst charging, and Green when fully charged.
User manual
Product Specication
Power Output: 2.5W
Speaker: 51mm
Frequency Response: 100-20,000 Hz
SNR: >89dB
Size: 110mm x 120mm x 95mm
Charging Time: 4 hours
Playing Time: 6.5 hours
Warning
- This speaker contains a lithium battery. It must be used and charged correctly
- Improper use of this speaker may cause the battery to catch re or explode resulting in
serious or fatal injury
- The battery shall not be exposed to excessive heat such as sunshine, re or suchlike
Caution
- Do not disassemble or modify the speaker
- Do not plave the speaker in direct sunlight, near res, stoves or other high temperatures
- Do not expose the speaker to water, salt water or allow the speaker to get wet
- If you dispose of the speaker, remember it contains a lithium battery and recycle
accordingly
Correct disposal of this product
This marking indicates that this product should not be disposed of with
other household wastes throught the EU.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of material resources.
To return your used devices, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for environmentally
safe recycling.
For Support, please contactMixx Audio
via the website at www.mixx-audio.com
or email support at: [e-mail]
3
Mixx S3 User Manual v1.indd 1-5 30/06/2016 23:03
Listening to Music
1. Check if the Bluetooth Status LED is ashing (ready to pair) or continuously
lit (paired and connected to a phone / music player). To enter pairing mode
simultaneously press and hold the ‘Up’ and ‘Down’ buttons.
2. To pair your phone with the Mixx S3, go to your bluetooth settings and
search for ‘Mixx S3’ then pair with the speaker (you may need to consult
your phone / music players instruction manual for specic pairing
instructions). Once pairing has completed, the Bluetooth Status LED will
be lit continuously
3. Select music to play on your phone. Adjust the volume on your phone
to maximum, then use the ‘UP’/’Down’ buttons on the rear panel of the
speaker to adjust the volume to the desired listening level.
4. To listen to music via the AUX in socket, use a 3.5mm audio cable (not
included) to connect the speaker to your music source. The Bluetooth
Status LED will illuminate GREEN to indicate it is in AUX In mode, and
the Auxilliary input will automatically be selected for audio playback.
Answering Calls
Should you receive a phone call whilst using the Mixx S3 with
Bluetooth, you can answer it and talk hands free using the
built in microphone on the front of the Mixx S3. Answer the
call from the screen on your phone and select ‘Mixx S3’ as the
speaker for the call.
Note: The background noise may increase when the battery
charge level is low. Some audio devices such as laptops
may generate increased noise at higher volumes.
Charging the S3
When the Mixx S3 displays ‘LO’ on the clock this indicates that it
is time to charge the internal battery. Use the supplied USB cable
and power adapter to charge the battery from the nearest
convenient wall outlet. The Charge Status LED will illuminate Orange
whilst charging, and Green when fully charged.
NekFit Sports

Important safety notices
Please read this instruction manual and keep it in a safe place for future
reference.
1. In order to avoid damage to your hearing please adjust the volume level
to a comfortable setting - do not listen to loud music for long periods of
time
2. Be aware of the situation around you and remove your earphones when
hearing is required to keep you safe
3. Do not use the earphones to listen to music, make or receive calls whilst
driving or operating machinery
4. Store this product and it’s accessories away from children
5. This product is not water resistant and should be kept clean and dry
6. Use only attachments or accessories as specified by the manufacturer
7. CAUTION: This product contains a lithium battery. Incorrect disposal of
this battery may result in explosion
8. The recommended operating temperature range for this product is 5 - 40
degrees Celsius
Box Contents
Mixx earphones
User Manual
USB Charging Cable
3 sizes of ear cushion (Medium installed on earphones)
Additional ear cushions
(Large and Small)
Charging the earphones
1. Plug the micro USB cable into the Micro USB charging port under the
cover on the front of the right hand earphone (5). Plug the USB cable into
a suitable USB socket on your computer or on a USB wall charger
2. A red light will illuminate to show that the battery is charging
3. When charging is complete, the red light will turn blue
Charging time is approximately 1 to 2 hours
Pairing and connecting
1. With the earphones turned off, press and hold the Multi Function button,
keeping the button pressed until the earphones enter pairing mode
(alternately flashing red and blue light) - note: if the earphones are already
turned on, you must turn them off before entering paring mode
2. On your Bluetooth enabled source device, switch on Bluetooth and
search for the Mixx Nekfit Sports earphones
3. Select the earphones to pair with them. The indicator light will blink blue
to indicate that the earphones are connected to your bluetooth source
Note: if your Bluetooth source asks for a passcode to connect to the
earphones, enter ‘0000’
Turning on / off the earphones
1. Press and hold the Multi Function button for 3 seconds to turn on the
earphones and automatically re-connect with the last used Bluetooth
source device. The status light will blink blue to indicate the earphones are
turned on
2. To turn off the earphones, press and hold the Multi Function button for 4
seconds. The status light will flash red four times and then turn off,
indicating that the earphones are now powered off
Listening to Music
1. Connect your bluetooth source device to the earphones (see Pairing and
connecting)
2. Select the music you wish to listen to and press Play
3. Control the music from your source device, or from the remote on the
earphones. The Multi Function button may be pressed once to play/pause
music, or to accept and end an incoming call. Press and hold the Multi
Function button to reject an incoming call, and double press the Multi
Function Button to redial the last number in your call log.
4. Press the volume Up or Down button once to increase or decrease the
volume. Press and hold the Up or Down button to skip tracks.
Note: the volume on your source device and the earphones may operate
independently. For optimal sound quality, set the volume level to maximum
on your source device, and then decrease the volume to the desired
listening level on the earphones.
Specifications
Bluetooth Version: 4.1
Bluetooth Range: 10m (free space)
Charge input: DC 5V/100mA
Charge time: 2 hours
Battery Life: Upto 5 hours (genre of music and volume level dependent)
Frequency Response: 20Hz-16KHz
Power Output: 5mW per channel (10mW total)
Customer Support is available at www.mixx-audio.com or by emailing
[email protected]
©2015 Bayan Audio Ltd.
MADE IN CHINA
NekFit Sports
② ③ ⑤① ④
(1) Volume Up / Previous
(2) Volume Down / Next
(3) Multi Function Button
(4) Indicator Light (rear
side)
(5) Charging Port

Important safety notices
Please read this instruction manual and keep it in a safe place for future
reference.
1. In order to avoid damage to your hearing please adjust the volume level
to a comfortable setting - do not listen to loud music for long periods of
time
2. Be aware of the situation around you and remove your earphones when
hearing is required to keep you safe
3. Do not use the earphones to listen to music, make or receive calls whilst
driving or operating machinery
4. Store this product and it’s accessories away from children
5. This product is not water resistant and should be kept clean and dry
6. Use only attachments or accessories as specified by the manufacturer
7. CAUTION: This product contains a lithium battery. Incorrect disposal of
this battery may result in explosion
8. The recommended operating temperature range for this product is 5 - 40
degrees Celsius
Box Contents
Mixx earphones
User Manual
USB Charging Cable
3 sizes of ear cushion (Medium installed on earphones)
Additional ear cushions
(Large and Small)
Charging the earphones
1. Plug the micro USB cable into the Micro USB charging port under the
cover on the front of the right hand earphone (5). Plug the USB cable into
a suitable USB socket on your computer or on a USB wall charger
2. A red light will illuminate to show that the battery is charging
3. When charging is complete, the red light will turn blue
Charging time is approximately 1 to 2 hours
Pairing and connecting
1. With the earphones turned off, press and hold the Multi Function button,
keeping the button pressed until the earphones enter pairing mode
(alternately flashing red and blue light) - note: if the earphones are already
turned on, you must turn them off before entering paring mode
2. On your Bluetooth enabled source device, switch on Bluetooth and
search for the Mixx Nekfit Sports earphones
3. Select the earphones to pair with them. The indicator light will blink blue
to indicate that the earphones are connected to your bluetooth source
Note: if your Bluetooth source asks for a passcode to connect to the
earphones, enter ‘0000’
Turning on / off the earphones
1. Press and hold the Multi Function button for 3 seconds to turn on the
earphones and automatically re-connect with the last used Bluetooth
source device. The status light will blink blue to indicate the earphones are
turned on
2. To turn off the earphones, press and hold the Multi Function button for 4
seconds. The status light will flash red four times and then turn off,
indicating that the earphones are now powered off
Listening to Music
1. Connect your bluetooth source device to the earphones (see Pairing and
connecting)
2. Select the music you wish to listen to and press Play
3. Control the music from your source device, or from the remote on the
earphones. The Multi Function button may be pressed once to play/pause
music, or to accept and end an incoming call. Press and hold the Multi
Function button to reject an incoming call, and double press the Multi
Function Button to redial the last number in your call log.
4. Press the volume Up or Down button once to increase or decrease the
volume. Press and hold the Up or Down button to skip tracks.
Note: the volume on your source device and the earphones may operate
independently. For optimal sound quality, set the volume level to maximum
on your source device, and then decrease the volume to the desired
listening level on the earphones.
Specifications
Bluetooth Version: 4.1
Bluetooth Range: 10m (free space)
Charge input: DC 5V/100mA
Charge time: 2 hours
Battery Life: Upto 5 hours (genre of music and volume level dependent)
Frequency Response: 20Hz-16KHz
Power Output: 5mW per channel (10mW total)
Customer Support is available at www.mixx-audio.com or by emailing
[email protected]
©2015 Bayan Audio Ltd.
MADE IN CHINA
NekFit Sports
② ③ ⑤① ④
(1) Volume Up / Previous
(2) Volume Down / Next
(3) Multi Function Button
(4) Indicator Light (rear
side)
(5) Charging Port

Important safety notices
Please read this instruction manual and keep it in a safe place for future
reference.
1. In order to avoid damage to your hearing please adjust the volume level
to a comfortable setting - do not listen to loud music for long periods of
time
2. Be aware of the situation around you and remove your earphones when
hearing is required to keep you safe
3. Do not use the earphones to listen to music, make or receive calls whilst
driving or operating machinery
4. Store this product and it’s accessories away from children
5. This product is not water resistant and should be kept clean and dry
6. Use only attachments or accessories as specified by the manufacturer
7. CAUTION: This product contains a lithium battery. Incorrect disposal of
this battery may result in explosion
8. The recommended operating temperature range for this product is 5 - 40
degrees Celsius
Box Contents
Mixx earphones
User Manual
USB Charging Cable
3 sizes of ear cushion (Medium installed on earphones)
Additional ear cushions
(Large and Small)
Charging the earphones
1. Plug the micro USB cable into the Micro USB charging port under the
cover on the front of the right hand earphone (5). Plug the USB cable into
a suitable USB socket on your computer or on a USB wall charger
2. A red light will illuminate to show that the battery is charging
3. When charging is complete, the red light will turn blue
Charging time is approximately 1 to 2 hours
Pairing and connecting
1. With the earphones turned off, press and hold the Multi Function button,
keeping the button pressed until the earphones enter pairing mode
(alternately flashing red and blue light) - note: if the earphones are already
turned on, you must turn them off before entering paring mode
2. On your Bluetooth enabled source device, switch on Bluetooth and
search for the Mixx Nekfit Sports earphones
3. Select the earphones to pair with them. The indicator light will blink blue
to indicate that the earphones are connected to your bluetooth source
Note: if your Bluetooth source asks for a passcode to connect to the
earphones, enter ‘0000’
Turning on / off the earphones
1. Press and hold the Multi Function button for 3 seconds to turn on the
earphones and automatically re-connect with the last used Bluetooth
source device. The status light will blink blue to indicate the earphones are
turned on
2. To turn off the earphones, press and hold the Multi Function button for 4
seconds. The status light will flash red four times and then turn off,
indicating that the earphones are now powered off
Listening to Music
1. Connect your bluetooth source device to the earphones (see Pairing and
connecting)
2. Select the music you wish to listen to and press Play
3. Control the music from your source device, or from the remote on the
earphones. The Multi Function button may be pressed once to play/pause
music, or to accept and end an incoming call. Press and hold the Multi
Function button to reject an incoming call, and double press the Multi
Function Button to redial the last number in your call log.
4. Press the volume Up or Down button once to increase or decrease the
volume. Press and hold the Up or Down button to skip tracks.
Note: the volume on your source device and the earphones may operate
independently. For optimal sound quality, set the volume level to maximum
on your source device, and then decrease the volume to the desired
listening level on the earphones.
Specifications
Bluetooth Version: 4.1
Bluetooth Range: 10m (free space)
Charge input: DC 5V/100mA
Charge time: 2 hours
Battery Life: Upto 5 hours (genre of music and volume level dependent)
Frequency Response: 20Hz-16KHz
Power Output: 5mW per channel (10mW total)
Customer Support is available at www.mixx-audio.com or by emailing
[email protected]
©2015 Bayan Audio Ltd.
MADE IN CHINA
NekFit Sports
② ③ ⑤① ④
(1) Volume Up / Previous
(2) Volume Down / Next
(3) Multi Function Button
(4) Indicator Light (rear
side)
(5) Charging Port

Important safety notices
Please read this instruction manual and keep it in a safe place for future
reference.
1. In order to avoid damage to your hearing please adjust the volume level
to a comfortable setting - do not listen to loud music for long periods of
time
2. Be aware of the situation around you and remove your earphones when
hearing is required to keep you safe
3. Do not use the earphones to listen to music, make or receive calls whilst
driving or operating machinery
4. Store this product and it’s accessories away from children
5. This product is not water resistant and should be kept clean and dry
6. Use only attachments or accessories as specified by the manufacturer
7. CAUTION: This product contains a lithium battery. Incorrect disposal of
this battery may result in explosion
8. The recommended operating temperature range for this product is 5 - 40
degrees Celsius
Box Contents
Mixx earphones
User Manual
USB Charging Cable
3 sizes of ear cushion (Medium installed on earphones)
Additional ear cushions
(Large and Small)
Charging the earphones
1. Plug the micro USB cable into the Micro USB charging port under the
cover on the front of the right hand earphone (5). Plug the USB cable into
a suitable USB socket on your computer or on a USB wall charger
2. A red light will illuminate to show that the battery is charging
3. When charging is complete, the red light will turn blue
Charging time is approximately 1 to 2 hours
Pairing and connecting
1. With the earphones turned off, press and hold the Multi Function button,
keeping the button pressed until the earphones enter pairing mode
(alternately flashing red and blue light) - note: if the earphones are already
turned on, you must turn them off before entering paring mode
2. On your Bluetooth enabled source device, switch on Bluetooth and
search for the Mixx Nekfit Sports earphones
3. Select the earphones to pair with them. The indicator light will blink blue
to indicate that the earphones are connected to your bluetooth source
Note: if your Bluetooth source asks for a passcode to connect to the
earphones, enter ‘0000’
Turning on / off the earphones
1. Press and hold the Multi Function button for 3 seconds to turn on the
earphones and automatically re-connect with the last used Bluetooth
source device. The status light will blink blue to indicate the earphones are
turned on
2. To turn off the earphones, press and hold the Multi Function button for 4
seconds. The status light will flash red four times and then turn off,
indicating that the earphones are now powered off
Listening to Music
1. Connect your bluetooth source device to the earphones (see Pairing and
connecting)
2. Select the music you wish to listen to and press Play
3. Control the music from your source device, or from the remote on the
earphones. The Multi Function button may be pressed once to play/pause
music, or to accept and end an incoming call. Press and hold the Multi
Function button to reject an incoming call, and double press the Multi
Function Button to redial the last number in your call log.
4. Press the volume Up or Down button once to increase or decrease the
volume. Press and hold the Up or Down button to skip tracks.
Note: the volume on your source device and the earphones may operate
independently. For optimal sound quality, set the volume level to maximum
on your source device, and then decrease the volume to the desired
listening level on the earphones.
Specifications
Bluetooth Version: 4.1
Bluetooth Range: 10m (free space)
Charge input: DC 5V/100mA
Charge time: 2 hours
Battery Life: Upto 5 hours (genre of music and volume level dependent)
Frequency Response: 20Hz-16KHz
Power Output: 5mW per channel (10mW total)
Customer Support is available at www.mixx-audio.com or by emailing
[email protected]
©2015 Bayan Audio Ltd.
MADE IN CHINA
NekFit Sports
② ③ ⑤① ④
(1) Volume Up / Previous
(2) Volume Down / Next
(3) Multi Function Button
(4) Indicator Light (rear
side)
(5) Charging Port