Mobilogix ATD310S User manual

www.mobilogix.com
Mobilogix
ATD310S
Theory of operation:
This is a Wireless Headlight Controller (WHC) with multi-functional device including Cellular, Bluetooth, and
NFC communications interfaces.
The device will remain in a sleep mode while in a stationary position. The device can wake up from either of
the following scenarios.
In scenario 1, the device will wake up and go into a “Stolen Mode”, meaning the device has been moved
without authorized consent from the home server. In this mode the tracker will begin broadcasting location
and sensor information to home server, so the correct actions can be taken to retrieve the stolen device.
In scenario 2, the device obtains authorized consent to be moved and goes into a “Trip” mode. In this mode
the device logs and broadcasts sensor and location information so the user’s trip can later be analyzed, after
the user has deactivated the tracker.
Via the LTE CAT1 network or BLE, the device will go back into a sleep mode to conserve power.
The device will draw the majority of its power from the trackers host asset, which is a much larger supply.
However, there will be a smaller onboard Li-Po battery attached to the tracker, just in case the host’s supply
runs out. There is no physical on/off switch on this device, but there is a button that will wake up the device
from sleep mode. Once it is connected to a supply it will begin to run, unless, a BLE or cellular command
gives the tracker a shutdown command.

Mobilogix
ATD310S
5500 Trabuco Road, Suite 150, Irvine, CA 92620
Tel: [phone]
Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc.
Other registered trademarks thatappear on this brochure are the property of the respective owners
© 2019 Mobilogix, Inc.
Module Interface

Mobilogix
ATD310S
5500 Trabuco Road, Suite 150, Irvine, CA 92620
Tel: [phone]
Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc.
Other registered trademarks that appear on this brochure are the property of the respective owners
© 2019 Mobilogix, Inc.
Module Assembly Detail:
Battery Holder
Back panel of the device

Mobilogix
ATD310S
5500 Trabuco Road, Suite 150, Irvine, CA 92620
Tel: [phone]
Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc.
Other registered trademarks that appear on this brochure are the property of the respective owners
© 2019 Mobilogix, Inc.
Complete assembled
front side of the device.
Used 6 of the same
screws as used for front
cover to secure the
enclosure
Internal battery
Connectors for the
main source
Complete assembled
back side of the
device.
Used 6 of the same
screws as used for PCB
to secure the enclosure
Battery
connection

Mobilogix
ATD310S
5500 Trabuco Road, Suite 150, Irvine, CA 92620
Tel: [phone]
Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc.
Other registered trademarks that appear on this brochure are the property of the respective owners
© 2019 Mobilogix, Inc.
FCC Interference Statement (Part 15.105 (b))
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Part 15 Clause 15.21
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
FCC Part 15.19(a) [interference compliance statement], unless the following statement is already provided
on the device label
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Mobilogix
ATD310S
5500 Trabuco Road, Suite 150, Irvine, CA 92620
Tel: [phone]
Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc.
Other registered trademarks that appear on this brochure are the property of the respective owners
© 2019 Mobilogix, Inc.
ISED RSS-Gen Notice
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
FCC RF Exposure Guidance Statement
In order to comply with FCC/ISED RF Exposure requirements, this device must be installed to provide at
least 20 cm separation from the human body at all times.
ISED RF Exposure Guidance Statement
In order to comply with FCC/ISED RF Exposure requirements, this device must be installed to provide at
least 20 cm separation from the human body at all times.
Afin de se conformer aux exigences d'exposition RF FCC / ISED, cet appareil doit être installé pour fournir
au moins 20 cm de séparation du corps humain en tout temps.

Mobilogix
ATD310S
5500 Trabuco Road, Suite 150, Irvine, CA 92620
Tel: [phone]
Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc.
Other registered trademarks that appear on this brochure are the property of the respective owners
© 2019 Mobilogix, Inc.
Key Hardware Components and Specifications
Hardware Components and Specifications
Component/Spec
Description
Quectel EG91-NA modem
• Qualcomm MDM 9207 chipset
• LTE CAT1
• 3GPP Rel. 11
• FOTA
• Embedded GPS/GNSS
Antennas
Embedded Cellular/GNSS/Bluetooth
Operating Frequency Band
(RF)
WCDMA850: 824-849MHz (TX), 869-894MHz (RX)
WCDMA1900: 1850-1910MHz (TX), 1930-1990MHz (RX)
WCDMA2100: 1920-1980MHz (TX), 2110-2170MHz (RX)
LTE BAND 2:1850-1910MHz (TX); 1930-1990MHz (RX)
LTE BAND 4: 1710-1755MHz (TX); 2110-2155MHz (RX)
LTE BAND 5: 824-849MHz (TX); 869-894MHz (RX)
LTE BAND 12: 699-716MHz (TX); 729-746MHz (RX)
LTE BAND 13: 777-787MHz (TX); 746-756MHz (RX)
BT: 2402-2480MHz (TX&RX)
GPS:1575.42MHz (RX)
Modulation mode
WCDMA: Uplink: BPSK; Downlink: QPSK/16QAM/ 64QAM
LTE: QPSK, 16QAM
Bluetooth: GFSK, π/4-DQPSK, 8DPSK
GPS: BPSK
Max. of Transmit power
WCDMA850/900/1900/2100: 24+1/-3dBm
LTE: Band 1/2/3/4/5/7/8/28/40: 23±2.7dBm
BLE: 3.68dBm
Maximum of Antenna’s Gain
WCDMA850: 1.42dBi
WCDMA1900: 1.42dBi
WCDMA2100: 1.42dBi
LTE B2: 1.42dBi
LTE B4: 1.42dBi
LTE B5: 1.42dBi
LTE B12: 1.42dBi
LTE B13: 1.42dBi
Bluetooth:2.13dBi
GPS:0.1 dBi
SIM card slot
3FF Verizon SIM
Power ON/OFF
Powered by Lithium Polymer battery
Battery
Rechargeable Lithium Polymer
• 3.7V
• 2000mAh
Charging
Internal battery will be charged by host power supply
Operating temperature
-20°C to +65°C
Dimensions
143.9 x 69.3 x 15mm
Certifications
FCC/IC/Verizon