Mobilogix ATD500S User manual

www.mobilogix.com
Mobilogix
ATD500S
User Guide
How to turn the BAT on
•If the battery is not dead, the BAT device will always be on and transmitting according to current firmware
intervals.
Current firmware summary V2.0.0.B406
•The current firmware takes a reading of all the sensors and then makes a cellular broadcast to the fusion
platform once every 12 hours which reports Sensor and location data.
•If you choose to set the Vibration Detection alarm on the fusion platform. Then the device will switch to a 5-
minute reporting mode. every time the BAT is moved. It will stay in this mode if the device is not moved for
another 5 minutes and then switch back to the 12 -hour mode.
•When the Mirco-B USB is plugged in will trigger than BG96 to wake up and flash LED indicators. While the
USB is plugged in the device will not report correctly. Plugging the USB should only be used to charge device
or for the user to debug or change BG96 settings Via AT commands. See page 8 for Quectel drivers.
Charging the BAT- To get a full charge look at the color of the power LED and charge accordingly
Note: These numbers are based on a 500ma source
•If the power LED is green when plugged in, then charge the device for 2 hours and 15 minutes.
•If the power LED is yellow when plugged in, then charge the device for 3 hours.
•If the power LED is red when plugged in, then charge the device for 3 hours and 45 minutes.
Vibration Detection
alarm turned ON
through the Fusion
Platform
LEDs flashing and
BG96 on when a
powered USB is
plugged into the BAT

Mobilogix
ATD500S
5500 Trabuco Road, Suite 150, Irvine, CA 92620
Tel: [phone]
Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc.
Other registered trademarks that appear on this brochure are the property of the respective owners
© 2017 Mobilogix, Inc.
LED Indicators
Data LED:
Slow, short blinks………… Trying to register
on network
Slow, Long blinks…………..Registered and
idle
Fast blinks……………………..Data transfer in
progress
Power LED:
Cycles through red, yellow, green upon startup
After startup it will blink 1 of 3 colors which represents
approximate battery life
Green……………………….40%-100%
Yellow………………………20%-40%
Red…………………………..Below 20%
GNSS LED:
Blinking……………………Acquiring
location
Solid…………………………Location
acquired

Mobilogix
ATD500S
5500 Trabuco Road, Suite 150, Irvine, CA 92620
Tel: [phone]
Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc.
Other registered trademarks that appear on this brochure are the property of the respective owners
© 2017 Mobilogix, Inc.
Device Assembly
1.Place clear plastic
lens in enclosure hole.
5.Place back on.
4.Place double sided
tape facing up.
3.Place battery down
as shown.
2.Place PCB with sim card holder facing
up. And USB in enclosure opening.

Mobilogix
ATD500S
5500 Trabuco Road, Suite 150, Irvine, CA 92620
Tel: [phone]
Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc.
Other registered trademarks that appear on this brochure are the property of the respective owners
© 2017 Mobilogix, Inc.
Programming Fixture
Device programming Applications
Atmel Studio, used to
program the SAMD20.
QPST, used to program
the BG96.
ESPFlashtool, used to
program the Esp8285.
Simplicity Studio, used to
program the BGM13P.

Mobilogix
ATD500S
5500 Trabuco Road, Suite 150, Irvine, CA 92620
Tel: [phone]
Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc.
Other registered trademarks that appear on this brochure are the property of the respective owners
© 2017 Mobilogix, Inc.
FCC Interference Statement (Part 15.105 (b))
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. Consult the dealer or an experienced radio/TV technician for help.
FCC Part 15 Clause 15.21
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
FCC Part 15.19(a) [interference compliance statement], unless the following statement is already
provided on the device label
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Mobilogix
ATD500S
5500 Trabuco Road, Suite 150, Irvine, CA 92620
Tel: [phone]
Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc.
Other registered trademarks that appear on this brochure are the property of the respective owners
© 2017 Mobilogix, Inc.
ISED RSS-Gen Notice
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1) l’appareil ne doit pas produire de brouillage;
2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’encompromettre le fonctionnement.
FCC RF Exposure Guidance Statement
In order to comply with FCC/ISED RF Exposure requirements, this device must be
installed to provide at least 20 cm separation from the human body at all times.
ISED RF Exposure Guidance Statement
In order to comply with FCC/ISED RF Exposure requirements, this device must be
installed to provide at least 20 cm separation from the human body at all times.
Afin de se conformer aux exigences d'exposition RF FCC / ISED, cet appareil doit être
installé pour fournir au moins 20 cm de séparation du corps humain en tout temps.

Mobilogix
ATD500S
5500 Trabuco Road, Suite 150, Irvine, CA 92620
Tel: [phone]
Mobilogix, the logo and the M design are trademarks of Mobilogix, Inc.
Other registered trademarks that appear on this brochure are the property of the respective owners
© 2017 Mobilogix, Inc.
Key Hardware Components and Specifications
Hardware Components and Specifications
Component/Spec
Description
Quectel BG96-G modem
• Qualcomm chipset
• LTE CAT M1
• 3GPP Rel. 11
• FOTA
• Embedded GPS/GNSS
Antennas
Embedded Cellular/GNSS/Bluetooth/WiFi receiver only
SIM card slot
3FF Verizon SIM
Power ON/OFF
Powered by Lithium Polymer battery
Battery
Rechargeable Lithium Polymer
• 3.7V
• 1700mAh
Charging
Internal battery will be charged through AC plague in or
5volt USB.
Operating temperature
-20°C to +85°C
Dimensions
121.50 x 58 x 16.72mm
Certifications
FCC/IC/Verizon