Module Electronic CHS-06.01 User manual

HEATING ACTUATOR
CHS-06.01
PASSPORT
МГРЛ-27.12.1931-005.02 ПС
page 1
BASIC INFORMATION
The heating actuator is designed to control water heating systems with thermoelectric valves with a supply
voltage of 24V DC.
• 6 independent outputs 24V DC
• Ability to connect up to 3 valves per output
• LED indication of output status
• Valve NO / NC operation mode selection
• Function of protection of valves against «sticking»
• Short circuit and overload protection
• Saving settings during a KNX power failure
• Power supply via KNX bus
• Valves powered by external 24V DC power supply
• Waterproof housing IP 64
Module Electronic LLC
module-electronic.ru, [email protected]
phone: [phone]

Device model
CHS-06.01
Outputs (control channels)
Number of outputs
6
Output type
MOSFET
Rated current per output
1A/24V DC
Number of connected valves to the output
up to 3 pcs.
Short circuit protection
Yes
Overload protection
Yes
Cross-section of the connected wire to the screw
terminals
0,5-4mm²
KNX interface
Specification
TP-256
Available application soware
ETS 5
KNX connector
4-wire EIB connector (PUSH WIRE spring clips) for standard
cable TP1 0,8мм Ø
Power supply
via KNX bus
Consumption on the KNX bus (29V DC)
< 5mA
< 150mA
Valve power
External power supply 24V DC
Operation temperature
0°C .. + 45°C
Operation humidity
5 .. 95% (no condensation)
Degree of protection
IP 64, clean environment
Mounting type
Wall mounting
Dimensions
145 х 71,5 х 55mm
Weight
235g
page 2
SPECIFICATIONS

GENERAL VIEW
4
5
6 - KNX connector
- Programming button
- Programming LED
- Input 24В DC
- Outputs 24В DC
- Output status indicator LED
- External power indicator LED
- Cable glands
1
2
3
4
5
6
1
7
2
3
7
8
before entering the cable Make a puncture
in the center of the pressure seal membrane with an awl
1212
11
10
9
8
7
6
5
4
3
Valve 1
М
Valve 2
М
Valve 3
М
Valve 5
М
Valve 4
М
Valve 6
М
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6
+V1+ V1-
DC 24V
+
-
KNX
_+++++ _____
8
130mm
Ø 5mm (for screw М4)
Mounting Hole Size
40mm
PASSPORT
МГРЛ-27.12.1931-005.02 ПС
CHS-06.01
page 3
Connect no more than 3 valves per channel!
WIRING DIAGRAMS
KNX bus
External
power supply

SAFETY INSTRUCTIONS
ATTENTION! Installation and connection of the device to the mains must only be carried out by
qualified personnel! Be sure to turn off the power before installing or removing the device! Even when
the device is turned off, the output terminals can be live! Do not connect to the outputs a load that
exceeds the recommended values! The design of the device meets the requirements of electrical
safety according to GOST 12.2.007.0-75.
SETTING INSTRUCTIONS
The device is set up in accordance with the instruction manual. (The full manual and application program can be
downloaded at https://module-electronic.ru/documents or by scanning the QR code at the bottom of the
document).
TRANSPORTATION, STORAGE AND DISPOSAL
The conditions for the transportation of devices must comply with conditions 5 of GOST 15150-69.
Storage of devices in packaging at the warehouses of the manufacturer and consumer must comply with storage
conditions 1 in accordance with GOST 15150-69. Aer transportation or storage at low temperatures, it is
necessary to withstand the device at room temperature for at least 2 hours before turning it on. Do not dispose
of the device with household waste.
WARRANTY
Warranty period - 12 months from the date of sale to the consumer. The manufacturer is not liable and does not
indemnify for damage caused by the fault of the consumer in case of non-compliance with the conditions of
transportation, storage, installation and operation, as well as in case of violation of the seal when trying to repair
the device yourself.
All the necessary information on the warranty can be obtained by the consumer by calling Module Electronics or
on the website: www.module-electronic.ru.
Serial number
page 4
Made in Russia
Name, address of the trading organization
Date of sale
Seller Signature
seller's stamp
module-electronic.ru
User Manual