Modus Furniture International PARAGON User manual

A. E. I.
F. J.
G.
H.
HEADBOARD LEFT SIDERAIL
RIGHT SIDERAIL
STORAGES
CENTER SLAT
STORAGE FEETS
LONG LEG SUPPORTS
HARDWARE BOX*
1 PC 1 PC
1 PC
2 PCS
1 PC
12 PCS
4 PCS
PARTS AND FITTING PACKAGING DETAIL
BOX #1
BOX #2
BOX #4
BOX #3
K. BED SLATS
14 PCS
UPDATED : MARCH 28TH, 2012
PARAGON STORAGE BED
C-KING SIZE
ASSEMBLY INSTRUCTIONS
K
I
I
J
MODUS
FURNITURE
INTERNATIONAL
MFI
HARDWARE* PACKED IN BOX #2
TOOL REQUIRED :
PHILLIPS HEAD SCREW
DRIVER (NOT PROVIDED)
1
4
2
3
ROUND HEAD
SCREW 15MM
40MM
ALLEN BOLT
WOOD SCREW
8X30MMØ
ALLEN KEY
12
18
8
1
PCS
PCS
PCS
PC
PARAGON STORAGE BED ASSEMBLED
YOUR BOX
MAY CONTAIN
EXTRA HARDWARE
8
PCS
HARDWARE* PACKED IN BOX #1
12 3 4
35MM
ALLEN BOLTS SPRING
WASHER WASHER ALLEN KEY
88 1
PCS PCS PC
FOLLOW THE ILLUSTRATION, PUT THE ALLEN
BOLT IN THE PREDILLED HOLE ARE TURNING
TO UNIFY THE HEADBOARD LEG TO
THE HEADBOARD PANEL
(B/C)
(A)
*FOR STEP 1 USE HARDWARE PACKED
IN BOX #1
STEP 1 :
B
C
A
4
3
2
1
C
A
B.
C.
D.
HEADBOARD LEG - LEFT
HEADBOARD LEG - RIGHT
FOOTBOARD
HARDWARE BOX*
1 PC
1 PC
1 PC
D
BC
A
F
G
H
E

STEP 3 :
FIX THE OTHER END OF LEFT SIDERAIL ( ) TO THE
FOOTBOARD ( ).
E
D
STEP 4 :
FIX RIGHT SIDERAIL ( ) TO THE HEADBOARD ASSY
( ) AND FOOTBOARD ( ).
F
A/B/C D
STEP 5 :
SECURE BOTH SIDERAILS ( ) TO THE HEADBOARD ASSY
( ) AND FOOTBOARD ( ) USING ROUND HEAD
SCREWS ( )
AS SHOWN IN THE ILLUSTRATION.
E,F
A/B/C D
1
STEP 6 :
REMOVE PLASTIC COVER FROM STORAGE FEETS ( )
BOLT.
J
FOLLOW THE ILLUSTRATION TO FIX STORAGE
FEETS ( ) TO STORAGE ( ).J I
FIX LEFT SIDERAIL ( ) TO THE HEADBOARD ASSY
( )
E
A/B/C BY SLIDING IN THE HOOK INSTALLED
AT THE END OF LEFT SIDERAIL ( ) TO THE
HEADBOARD ASSY ( ), AND PUSH DOWN
THE LEFT SIDERAIL ( ) TO SECURE THE
CONNECTION.
E
A/B/C
E
STEP 2 :
A/B/C
E
E
A/B/C
PUSHING
DOWN
UPDATED : MARCH 28TH, 2012
1
1
1
A/B/C
E
A/B/C A/B/C
EE
F
D
D
I
J
I
J
J
J
J
J
J

STEP 11 :
FIX STORAGE ( ) TO RIGHT SIDERAIL ( ) USING
ALLEN BOLTS ( ).
I F
4
TURN LEVELER UNDERNEATH STORAGE FEETS ( )
TO ADJUST THE STORAGE ( ) LEVEL AS SHOWN
ON ILLUSTRATION.
J
I
STEP 8 :
J
STEP 10 :
STEP 9 :
UPDATED : MARCH 28TH, 2012
INSTRUCTIONS FOR ADJUSTING
LEVELERS:
POSITION THE BED IN YOUR ROOM
LOCATE LEVELERS UNDER EACH
CENTER LEG ( ).
TURN COUNTER-CLOCKWISE TO
EXTEND, CLOCKWISE TO CONTRACT.
ADJUST LEVELERS UNTIL EACH LEG
IS APPLYING EQUAL UPWARD
PRESSURE ON THE CENTER SLAT.
H
REMOVE BOX SPRING AND MATTRESS BEFORE
MOVING YOUR BED.
LIFT YOUR BED WHEN MOVING IT.
DRAGGING CAN DAMAGE CENTER SUPPORT.
READJUST LEVELERS AFTER MOVING YOUR BED.
I
I
I
MAINTENANCE INSTRUCTIONS:
ARRANGE CENTER SLAT ( ) SO THAT T-NUTS ARE
FACING THE FLOOR. SLIDE ALLEN BOLTS ( ) FROM
TOP OF CENTER SLAT ( ) INTO THE 2ND, 5TH, 6TH,
AND 9TH PREDRILLED HOLES. FIX LONG LEG
SUPPORT ( ) TO CENTER SLAT ( ) USING ALLEN
BOLTS ( ) AND ALLEN KEY ( ).
G
4
G
H G
4 3
4
K
G
3
K
H
G
4
3
H
G
G
4
3
T-NUT
A/B/C
DF
E
K
E
2
K
FOLLOW THE ILLUSTRATION TO FIX STORAGE ( )
TO LEFT SIDERAIL ( ) USING ALLEN BOLTS ( ).
USE ALLEN KEY ( ) TO TIGHTEN THE BOLTS.
I
E 4
3
STEP 7 :
I
4
3
E
F
A/B/C
D
E
I4
4
4
4
EI
I
A/B/C
F
D
4
4
4
4
FOLLOW THE ILLUSTRATION TO PLACE THE BED SLATS
( ) ON THE BED FRAME.KSPREAD BED SLATS ( ) ON BED
FRAME. FIX 1ST, 7TH, 8TH, AND 14TH BED SLATS TO
BED FRAME USING WOOD SCREWS ( ). USE PILOT
HOLES ON SIDERAILS ( ) AS REFERENCE FOR
CORRECT PLACEMENT.
K
2
E,F
FOLLOW THE ILLUSTRATION TO SPREAD OUT ALL THE BED
SLATS ( ).KSLIDE CENTER SLAT ( ) UNDER BED SLATS ( ).
SLIDE ALLEN BOLTS ( ) FROM TOP OF BED SLATS ( )
THROUGH PRE-DRILLED HOLES ON 1ST, 2ND, 5TH, 10TH,
13TH AND 14TH BED SLATS. TIGHTEN ALLEN BOLTS ( )
WITH ALLEN KEY ( ) TO SECURE BED SLATS ( )
TO CENTER SLAT ( ).
G K
4 K
4
3 K
G