Modus Furniture International TOWNSEND STORAGE BED User manual

TOWNSEND STORAGE BED
FULL/ QUEEN/ E-KING SIZE
ASSEMBLY INSTRUCTIONS
PARTS AND FITTING PACKAGING DETAIL
UPDATED : NOVEMBER 20TH, 2014
BOX #1
A. HEADBOARD 1 PC C. LEFT SIDERAIL 1 PC
D. RIGHT SIDERAIL 1 PC
E. CENTER SLAT 1 PC
BOX #2
B. FOOTBOARD 1 PC
A
B
TOWNSEND STORAGE BED ASSEMBLED HARDWARE PACKED IN BOX #2
TOOL REQUIRED :
PHILLIPS HEAD SCREW
DRIVER (NOT PROVIDED)
YOUR BOX
MAY CONTAIN
EXTRA HARDWARE
1 2
ALLEN BOLT
40MM 26
PCS WOOD SCREW
Ø8X30MM 8 PCS
3
1
PC
ALLEN KEY
H. STORAGE KIT 2 PCS
G. LEG SUPPORT 4 PCS
BOX #3
I. BED SLAT 12 PCS
BOX #4
C
D
E
G
F. STRETCHER 2 PCS H
H
I
HARDWARE BOX *
F
F

UPDATED : NOVEMBER 20TH, 2014
REMOVE DRAWER BOX ASSEMBLY FROM FRAME OF THE STORAGE KIT (H) BY UNLOCKING METAL EXTENSION RAIL.
STEP 1 :
FOLLOW THE ILLUSTRATION TO FIX THE STORAGE KIT
(H) TO THE LEFT SIDERAIL (C) AND THE RIGHT
SIDERAIL (D) USING ALLEN BOLTS (1). USE ALLEN KEY
(3) TO TIGHTEN THE BLOTS.
STEP 2 : STEP 3 :
STEP 4 :
REPEAT THE SAME WAY FIX THE RIGHT SIDERAIL (D)
TO THE HEADBOARD (A)
STEP 5 :
A
C
D
FIX ONE OF THE LEFT SIDERAILS (C) TO THE
HEADBOARD (A) BY SLIDING IN THE HOOK
INSTALLED AT THE END OF THE LEFT SIDERAIL (C)
TO THE HEADBOARD (A), AND PUSH DOWN THE LEFT
SIDERAIL (C) TO SECURE THE CONNECTION.
PUSHING
DOWN
LEFT RIGHT
A
C
D
C
H
H
H
H
H
H
C
A
CH
3
3
1
1
1
1
1
11
11
1
1
1
1
1
*FIX THE OTHER END OF THE LEFT SIDERAIL (C) AND
THE RIGHT SIDERAIL (D) TO FOOTBOARD (B).
*FIX THE STRETCHER (F) TO THE STORAGE KIT (H)
USING ALLEN BOLT (1) AND ALLEN KEY (3).
*TURN LEVELER UNDERNEATH STORAGE LEG TO
ADJUST THE STORAGE KIT (H) LEVEL AS SHOWN ON
ILLUSTRATION.
A
B
D
C
F
3
H
1
1
1
F
H
HF
H

UPDATED : NOVEMBER 20TH, 2014
STEP 6 :
POSITION THE BED IN YOUR ROOM.
LOCATE LEVELERS UNDER EACH
LEG SUPPORT.
TURN COUNTER-CLOCKWISE TO
EXTEND, CLOCKWISE TO CONTRACT.
ADJUST LEVELERS UNTIL EACH LEG
SUPPORT IS APPLYING EQUAL UPWARD
PRESSURE ON THE CENTER SLAT.
INSTRUCTIONS FOR ADJUSTING
LEVELERS : MAINTENANCE INSTRUCTIONS :
REMOVE BOX SPRING AND MATTRESS
BEFORE MOVING YOUR BED.
LIFT YOUR BED WHEN MOVING IT.
DRAGGING CAN DAMAGE
CENTER SUPPORT.
READJUST LEVELERS AFTER MOVING
YOUR BED.
ARRANGE CENTER SLAT (E) SO THAT T-NUTS ARE
FACING THE FLOOR. SLIDE ALLEN BOLTS (1) FROM
TOP OF CENTER SLAT (E) IN TO THE 2ND, 4TH, 7TH,
AND 9TH PREDRILLED HOLES.
FIX LEG SUPPORT (G) TO CENTER SLAT (E) USING
ALLEN BOLTS (1) AND ALLEN KEY (3).
STEP 7 :
FOLLOW THE ILLUSTRATION TO SPREAD OUT
ALL THE BED SLATS (I). SLIDE CENTER SLAT (E)
UNDER BED SLATS (I). SLIDE ALLEN BOLTS (1)
FROM TOP OF BED SLATS (I)
THROUGH PRE-DRILLED HOLES ON 1ST, 2ND, 5TH,
8TH, 11TH AND 12TH BED SLATS.
TIGHTEN ALLEN BOLTS (1) WITH ALLEN KEY (3)
TO SECURE BED SLATS (I) TO CENTER SLAT (E).
STEP 8 : FOLLOW THE ILLUSTRATION TO PLACE THE BED SLATS
(I) ON THE BED FRAME. SPREAD BED SLATS (I) ON BED
FRAME. FIX 1ST, 6TH, 7TH, AND 12TH BED SLATS TO
BED FRAME USING WOOD SCREWS (2). USE PILOT
HOLES ON SIDERAILS (C,D) AS REFERENCE FOR
CORRECT PLACEMENT.
STEP 9 :
G
E
1
1
1
1
T-NUT
1
3
E
E
G
1
3
I
E
1
I
3
A
BD
C
I
I
C,D
2
INSERT DRAWER BOX ASSEMBLY TO FULL BODY
BED ASSEMBLY TO COMPLETE INSTALLATION.
A
B