modway EEI-2784 User manual

Page 1 of 4
Thank you for purchasing the DESK！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 45 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
A Long Bolt M6x75mm x4
B
G Allen Wrench M4 x1
D
Components:
1 Desk Top x1 2 Rail x2
4 Leg Ⅱ x2
3 Leg Ⅰ x2
Medium Bolt M6x65mm x2
Short Bolt M6x20mm x1
1
6 2
3
6 Metal Support Rail x2
4
6
3
4
5
5
5 End Panel x2
C Medium Bolt M6x55mm x4
E Spring Washer M6 x11
F Flat Washer M6 x11
DESK

Page 2 of 4
STEP 1:
STEP 2:
Put Desk Top (1) upside down on a carpeted or padded surface.
Place 2 pieces of Rail (2) to Desk Top (1) as shown.
Insert 4 pieces of Long Bolt (A) with 4 pieces of Spring Washer (E) and 4 pieces of Flat Washer (F) into the pre-drilled holes
on Desk Top (1) through the pre-drilled holes on Rails (2).
Use Allen Wrench (G) to tighten Long Bolts (A) clockwise until secure.
Hardware & Tools required
Hardware & Tools required
Ax4 Ex4 Fx4 Gx1
1
2
E
A
Place 1 piece of Leg I (3), 1 piece of Leg II (4) , and End Panels (5) to the assembled Desk Top (1) and Rails (2) as shown.
Insert 2 pieces of Medium Bolt (C) with 2 pieces of Spring Washer (E) and 2 pieces of Flat Washer (F) into the pre-drilled holes
on the end of Rail (2) through the pre-drilled holes on End panels (5).
Use Allen Wrench (G) to tighten Medium Bolts (C). Do not fully tighten Medium Bolts (C) at this step.
4
1
5
2
F
A
E
F
E
F
E
F
A
A
G
Cx2 Ex2 Fx2 Gx1
2
2
3
5
G
C
E
F
C
E
F
DESK

Page 3 of 4
STEP 3:
STEP 4:
Hardware & Tools required
Hardware & Tools required
Cx2 Ex2 Fx2 Gx1
Place 1 piece of Leg I (3), 1 piece of Leg II (4) , and End Panels (5) to the assembled Desk Top (1) and Rails (2) as shown.
Insert 2 pieces of Medium Bolt (B) with 2 pieces of Spring Washer (E) and 2 pieces of Flat Washer (F) into the pre-drilled holes
on the end of Metal Support Rail (6) through the pre-drilled holes on Legs (3&4).
Insert 1 piece of Short Bolt (D) with 1 piece of Spring Washer (E) and 1 piece of Flat Washer (F) into the pre-drilled holes on
Desk Top (1) through the pre-drilled holes on Metal Support Rails (6) as shown.
Use Allen Wrench (G) to tighten all Medium Bolts (B&C), Long Bolts (A), and Short Bolt (D) clockwise until secure.
5
Bx2 Dx1 Fx3 Gx1 Ex3
Place the remaining 1 piece of Leg I (3), 1 piece of Leg II (4) , and End Panels (5) to the assembled Desk Top (1) , Rails (2),
Leg I (3), and Leg II (4) as shown.
Insert 2 pieces of Medium Bolt (C) with 2 pieces of Spring Washer (E) and 2 pieces of Flat Washer (F) into the pre-drilled holes
on the end of Rail (2) through the pre-drilled holes on End panels (5).
Use Allen Wrench (G) to tighten Medium Bolts (C). Do not fully tighten Medium Bolts (C) at this step.
1
2
2
4
4
3
3
E C
F
G
C
E
F
5
2
2
1
4
4
3
3
6
6 B
E
F
G
D
F
E
G
B
E
F
DESK

Page 4 of 4
STEP 5:
Carefully turn over the assembled desk.
Assembly is complete. Your desk is ready to be used now!
DESK