modway EEI-3901 User manual

EEI-3901 GAMING CHAIR
Customer Service 609-256-9000︱www.modway.com Page 1of 5
Thank you for purchasing the MODWAY GAMING CHAIR!
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the Gaming chair, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Hardware:
Components:
Bolt M8x20mm x3
1. Back x1 2. Seat x1 3. Left Armrest x1 4. Right Armrest x1 5. Chassis x1
A.
Allen Wrench x1
6. Cylinder Column x1 7. Base x1 8. Castor x5 9. Plastic Cover
x1
C.
Flat Washer x11D.
Bolt M6x20mm x4
B.
Spring Washer x7
F.
E.
Bolt M6x25mm x8
10. Connection Plate x1 11. Pillow x1 12. Black Dust Cover x1

EEI-3901 GAMING CHAIR
Customer Service 609-256-9000︱www.modway.com Page 2of 5
STEP 1:
1. Attach the Connection Plate (10) to the Back (1) by using 4 pieces of Bolts (C) and 4 pieces of
Flat Washers (D) and 4 pieces of Spring Washers (E) as shown.
2. Use Allen Wrench (F) to tighten all Bolts (C) clockwise as shown.
STEP 2:
1. Attach the Left Armrest (3) to the Seat (2) by using 2 pieces of Bolts (C) and 2 pieces of
Flat Washers (D) as shown.
2. Repeat the same steps for the Right Armrest (4).
3. Use Allen Wrench (F) to tighten all Bolts (C) clockwise as shown.

EEI-3901 GAMING CHAIR
Customer Service 609-256-9000︱www.modway.com
Page 3of 5
STEP 3:
1. Attach the Chassis (5) to the Seat (2) by using 4 pieces of Bolts (B) as shown.
2. Use Allen Wrench (F) to tighten all Bolts (B) clockwise as shown.
STEP 4:
1. Attach the Connection Plate (10) to the the Chassis (5) by using 3 pieces of Bolts (A) and 3 pieces of
Flat Washers (D) and 3 pieces of Spring Washers (E) as shown.
2. Use Allen Wrench (F) to tighten all Bolts (A) clockwise as shown.

EEI-3901 GAMING CHAIR
Customer Service 609-256-9000︱www.modway.com
Page 4of 5
STEP 5:
1. Please put Base (7) on a carpeted or padded surface.
2. Insert 1 piece of Castor (8) into the Base (7) as shown by hand.
3. Repeat the same steps for the remaining 4 pieces of Castors (7).
4. Carefully turn over the assembled Base (7) and Insert the Cylinder Column (6) as shown.
5. Insert the Black Dust Cover (12) to the Cylinder Column (6) as shown.
STEP 6:
1. Put the Pillow (11) between the Seat (2) and the Back (3) as shown.
2. Insert the Chassis (5) into the Cylinder Column (6) as shown.

EEI-3901 GAMING CHAIR
Customer Service 609-256-9000︱www.modway.com
Page 5of 5
STEP 7:
Insert the Plastic cover (9) to the Back (1) as shown.
Your Gaming chair is ready to be used now!
Attention:
When you use the handle to
adjust the height to be lower,
please move away your feet
from the base at the same time.