modway MOD-6148 User manual

Customer Service 609-256-9000︱www.modway.com
Page 1of 6
MOD-6148/ 6149/ 6150/ 6151/ 6152/ 6153/ 6154/ 6155/ 6156/ 6157/ 6158/
6159/ 6160/6161/ 6162/ 6163/6164/ 6165/ 6166/6167 HEADBOARD
Thank you for purchasing the MODWAY HEADBOARD!
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the headboard, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6.Please keep all the fitting out of reach of children.
Hardware:
Components:
1. Headboard x1 2. Low post x2
(Style may vary)
Allen Wrench x1
Bolt M6x15mm x4
C.
A.
Arc Washer M6 x4
B.

Customer Service 609-256-9000︱www.modway.com
Page 2of 6
MOD-6148/ 6149/ 6150/ 6151/ 6152/ 6153/ 6154/ 6155/ 6156/ 6157/ 6158/
6159/ 6160/6161/ 6162/ 6163/6164/ 6165/ 6166/6167 HEADBOARD
STEP 1:
Note: Extra hardware were provided for attaching the headboard to your Bed Frame (use is optional).
Note: there are seven heights for your choice, please assemble at your desired height.
1. Insert Low Post (2) into the Headboard (1) as shown.
2. Attach by using Arc Washer (B) and Bolt (A) from the holes on the back of Low Post (2) and Headboard (1).
3. Use Allen Wrench (C) to tighten all Bolts (A) clockwise until secure at this step.
STEP 2:
Carefully turn up the assembled Headboard (1) by two adults.
Assembly is completed. The headboard is ready to use now!
NOTE: Hardware may loosen over time. Periodically check that all connections are tight.

Customer Service 609-256-9000︱www.modway.com
Page 3of 6
MOD-6148/ 6149/ 6150/ 6151/ 6152/ 6153/ 6154/ 6155/ 6156/ 6157/ 6158/
6159/ 6160/6161/ 6162/ 6163/6164/ 6165/ 6166/6167 HEADBOARD
ASSEMBLY INSTRUCTIONS
OPTION 1
Option 1 Hardware:
Components:
Bolt M6x45mm x4
A.
Bolt M6x65mm x4
B.
Flat Washer M6 x8
C.
Spring Washer M6 x4
D.
Nut M6 x4
E.
Allen Wrench x1
F.
G.
Spanner Wrench x1
1. Headboard x1 2. Bed frame x1

Customer Service 609-256-9000︱www.modway.com
Page 4of 6
MOD-6148/ 6149/ 6150/ 6151/ 6152/ 6153/ 6154/ 6155/ 6156/ 6157/ 6158/
6159/ 6160/6161/ 6162/ 6163/6164/ 6165/ 6166/6167 HEADBOARD
STEP 1:
1. Line up the Bed Frame (2) board’s pre-drilled holes to match those of the Headboard (1).
2. Secure the Headboard (1) to the Bed Frame (2) by using 2 pieces of Bolts (B) for the thicker
Bed Frame (2), and 2 pieces of Bolts (A) for the thinner Bed Frame (2).
3. Before inserting each bolt, place 1 piece of Spring Washer (D) and Flat Washer (C) on each bolt. Then
fit 1 piece of Flat Washer (C) and Nut (E) on the bolt as it protrudes through the Bed Frame (2) and the
Headboard (1) as shown.
4. Repeat the same procedure for each bolt and each side of the Bed Frame (2).
5. Use Allen Wrench (F) and Spanner Wrench (G) to tighten all Bolts (A or B) and Nut (E)
clockwise as shown.
STEP 2:
Carefully position the assembled bed to the desired location by four adults.
Assembly is completed. The bed is ready to use now!
NOTE: Hardware may loosen over time. Periodically check that all connections are tight.

Customer Service 609-256-9000︱www.modway.com
Page 5of 6
MOD-6148/ 6149/ 6150/ 6151/ 6152/ 6153/ 6154/ 6155/ 6156/ 6157/ 6158/
6159/ 6160/6161/ 6162/ 6163/6164/ 6165/ 6166/6167 HEADBOARD
ASSEMBLY INSTRUCTIONS
OPTION 2
Note: This is assembly instruction for Headboard connect to MODWAY Bed Frame.
Option 2 Hardware:
Components:
Bolt M6x45mm x4
A.
Bolt M6x65mm x4
B.
Flat Washer M6 x4
C.
Spring Washer M6 x4
D.
Allen Wrench x1
E.
1. Headboard x1 2. Bed frame x1

Customer Service 609-256-9000︱www.modway.com
Page 6of 6
MOD-6148/ 6149/ 6150/ 6151/ 6152/ 6153/ 6154/ 6155/ 6156/ 6157/ 6158/
6159/ 6160/6161/ 6162/ 6163/6164/ 6165/ 6166/6167 HEADBOARD
STEP 1:
1. Line up the Headboard (1) board’s pre-drilled holes to match those of the Bed Frame (2).
2. Secure the Headboard (1) to the Bed Frame (2) by using 2 pieces of Bolts (B) for the thicker
Bed Frame (2), and 2 pieces of Bolts (A) for the thinner Bed Frame (2).
3. Attach the Headboard (1) to the Bed Frame (2) by using 2 pieces of Bolts (B) with 2 pieces of Spring
Washers (D) and 2 pieces of Flat Washers (C) for the thicker Bed Frame (2) as shown.
4. Repeat the same procedure for each bolt and each side of the Bed Frame (2).
5. Use Allen Wrench (E) to tighten all Bolts (A or B) clockwise as shown.
STEP 2:
Carefully position the assembled bed to the desired location by four adults.
Assembly is completed. The bed is ready to use now!
NOTE: Hardware may loosen over time. Periodically check that all connections are tight.