modway MOD-6801 User manual

2
3
4
6
E
I
C
G
F
J
2
6801 QUEEN BED
20
16
8
32
5
padded area, in the room that it is intended for. Approximately assembly time:45 minutes.
Metal Connector
www.modway.com

U
to the bottom edge of
Use 8 pieces of Metal Connectors (K).
Allen Wrench (G).
Bolts (C)
Bolts (C)
Headboard (P1)
as shown .
Bolts (B)
Place upside down on a carpeted or padded.
E
G
G
G
kB E
EC
C
6801 QUEEN BED
2 pieces of
Secure by using
5
Headbaord (P1)
Connect two half of Headbaord (P1) by using
Flat Washer (E) and 8 pieces of
Allen Wrench (G) to tighten Bolts (B) clockwise until secure.
Place 1 piece of
UU Flat Washer (E) and 8 pieces of
Tighten by using
Please turn over the headboard by 2 people carefully.
as shown .
k
B
E
G
www.modway.com
Use 8 pieces of to connect from the back of assembled
Black Board (P8) Black Board (P8)
Headbaord (P1).
BOTTOM
TOP

Insert 8 pieces
Use 8 pieces of
Spring Washer (F)/ /
Bolts (A)
Bolts (A) Bolts (A).
GAEF
A
A
6801 QUEEN BED
8 8 8
Flat Washer (E)
and the bottom holes on the Footboard (P3) and Headbooard (P1) .
Leaving 0.3-0.4 inch space of the thread of Bolts (A) as shown for inserting the notch of Side Rail (P2).
Insert the notch of Side Rail (P2) into the space left on the Bolts (A).
5
E
77
E
G
AA
Attach Legs (P6) into Headbaord (P1) and Footboard (P3) as shown.
Secure by using Flat Washer (E) and
Allen Wrench (G) to tighten tightly.
into /
www.modway.com
P6
P6
P6
P6
P6
P1
P3
GAEF
8 8 8
F
F
G
E
E
A
A

Use
2 pieces of
Support Legs (P5) .
Attach 1 piece of
D
H
D
G
G
BGDH
GA
6801 QUEEN BED
Tighten all with after all assembled.
5
Support Legs (P5) to Center Rail (P4) by using Bolts (B) and Nuts (D)
as shown.
Allen Wrench (G) and Open Wrench (H) to tighten Bolts (B) and Nuts (D) until secure.
Repeat the same step for the remaining 3 pieces of
Attach one end of assembled Center Rail (P4) Headbaord (P1),
to
Use Allen Wrench (G) tofix Bolts (A) clockwise until secure.
Bolts (A&B&C) Allen Wrench (G)
2 pieces of
www.modway.com
P5
P5
P5 P5
P4
and secure by using 2 pieces of Bolts (A) .
Repeat the same steps for Footboard (P3) and Center Rail (P4).

into the holes on
Center Plastic Cover (I)
P7
P7
I
J
J
6801 QUEEN BED
5
Insert 2 pieces of Slat (P7) into 2 pieces of End Plastic Covers (J) and 1 piece of
as shown.
Then insert the assembled Center Plastic Cover (I) Center Rail (P4) ,
and the assembledEnd Plastic Cover (J) into the holes on Side Rail (P2) as shown.
Repeat the same steps for the remaining 24 pieces of Slats (P7) .
Step 7:
Assembly is complete. Your bed is ready to be enjoyed now !
www.modway.com