modway EEI–2803 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI–2803/2804 BAR TABLE
Hardware:
Component:
A Double-End Bolt x 4
1
Thank you for purchasing the MODWAY BAR TABLE!
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the bar table, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
C Flat Washer 1/4” x 16
4
3
Table Glass x1 2 Table Top x1 3 Table Leg x4
1
2
B Long Bolt 1/4”x35mm x 8
E Allen Wrench 1/4” x 1
4 Stretcher x1
3 3
3
D 1/4” x 16
F Wrench 1/4” x 1
G Plastic Cover x 4
Nut
Before you start, here are some helpful advice:

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
BAR TABLE
STEP 1:
STEP 2:
Please put Table Top (2) upside down on a carpeted or padded area.
Secure 4 pieces of Double-End Bolt (A) into the bottom of Table Top (2) as shown.
Put 4 pieces of Table Leg (3) to Table Top (2) through the assembled Double-End Bolt (A) as shown.
Ax4 Hardware & Tool required
2
A
A
A
A
2
3
3
3
3
EEI–2803/2804

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
BAR TABLE
STEP 3:
STEP 4:
Place Stretcher (4) to the assembled Table Top (2), and Table Legs (3) as shown.
Insert 8 pieces of Bolt (B) with 8 pieces of Flat Washer (C) into the holes on Table Leg (3) through the holes on Stretcher (4).
Use Allen Wrench (E) to tighten Bolts (B) clockwise until secure.
Secure 4 pieces of Nut (D) to the end of assembled Double-End Bolt (A) as shown.
Use Wrench (F) to tighten Nuts (D) clockwise until secure.
Bx8 Cx8 Ex1 Hardware & Tool required
Hardware & Tool required
Dx4 Fx1
2
2
3
D
3
3
3
3
4
4
3 C
B
E
D
D
D
F
D
F
3
3
3
3
4
EEI–2803/2804

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
BAR TABLE
STEP 5:
STEP 6:
Insert 4 pieces of Plastic Cover (G) into the assembled Table Leg (3) as shown.
Carefully turn over the assembled bar table.
Put Table Glass (1) to the Table Top (2) as shown.
Gx4 Hardware & Tool required
3
Assembly is complete. Your bar table is ready to be used now!
3
2
3
3
4
G
G
G
G
1
2
3
3
3
3
4
EEI–2803/2804