MoistMaster E35 BT Operating and maintenance instructions

MoistMaster® E35 BT
Quick Start Guides
The complete installation and operating
instructions can be found at www.moistmaster.fi
Read them and these Quick Start Guides carefully.
Commissioning of the Indoor Moisture Control Unit:
●Connect the sensor cable to the controller.
●Place the controller in the wall socket so that the indicator lights
flash. In this case, the automatic control starts.
●Attach the measuring sensor in the wall at height of about one
meter in a way that the measuring head opening is facing the
room
●Plug the heater into the socket on the controller.
●To test the function, briefly press the button on the controller,
the “ON” light will come on and the heater will start operating
when the button is pressed.
●A minimum temperature of 5 oC can be activated and
deactivated from the controller. Other settings must be
made with MoistMaster BlueTooth- application.
●When the minimum temperature of 5 oC is set, the “≥ 5 oC” indicator light
on the controller lights up.
●If desired, follow the instructions in this manual to install MoistMaster
BlueTooth -application. You can also use the controller without the
application.
Version 01-2022

Moisture Control Unit User Interface Guide
1. Probe for Micro USB connector
2. Power indicator (green LED)
3. Minimum temperature selection indicator (yellow
LED)
4. Sensor fault indicator (red LED)
5. Selection button:
●Power on test (while pushing the button down
the green LED lights up and the electricity is
connected to the heater)
●Minimum temperature ≥ 5 oC activation (push
button for approx. 10 sec, the yellow LED flashes until it lights up
continuously)
●Deactivation of the minimum temperature ≥ 5 oC (push button for approx. 10
sec, the yellow LED will flash until it goes out)
●Use the push button to reset the Bluetooth PIN to the default value of “0000”
(> 20 sec push)
Bluetooth application installation
Android app called "MoistMaster" from app stores (Apple Store, Google play) is
available for download on Android and Apple smartphones. The application can
be used to monitor measured values, select a moisture protection level and
change settings. Instructions for downloading and using the application can be
found on the www.moistmaster.fi website.
Version 01-2022

General safety instructions
To avoid the risk of electric shock, fire or other accidents, always follow the
warnings below when using the humidity control.
●Make sure that the power supply corresponds to the values on the safety
label and technical data of the humidity controller.
●The humidity controller may only be used for its primary purpose
●Keep the humidity controller dry and dust-free.
●Check the condition of the humidity controller control regularly. Do not use it
if it shows damage
●Only authorized personnel may repair the humidity controller. Do not open
the case.
Precautions
●Keep the humidity controller control visible and easy to disconnect.
●Follow carefully the instructions for using the heater to be connected to the
humidity controller.
●The heater to be connected to the socket must be designed for continuous
operation so that it can be switched off with an external switch. Some heaters
with a fan may operate in such a way that after the heating element has been
switched off, the fan will still run to cool the heater. This type of heater must
not be used with MoistMaster® E35 BT -controller.
●The humidity controller only prevents damage and inconvenience caused by
excessively humid indoor conditions. Separately, e.g. roof water leaks,
capillary rise in moisture from the soil, leaks from water fixtures, rainwater
damage and the like.
Version 01-2022

Technical data and restrictions
●Voltage 230VAC, 50Hz.
●Building supply fuse for the humidity
controller max. 16 A
●The humidity controller does not include
fuses or overcurrent protection devices
●Maximum heater power 3500 W (building
supply fuse 16 A)
●Maximum heater power 2200 W (building
supply fuse 10 A)
●Enclosure class IP20. For indoor use only.
●Permissible ambient temperature range -40 oC … + 40 oC .
The humidity controller is disposed of with electronic waste.
MoistMaster® E35 BT is CE approved
MoistMaster® E35 BT -controller and sensor have a two (2) year warranty.
The humidity controller has been developed in Finland.
Version 01-2022